ColorKey CKU-5052 Mover Spot 150 Fixture User Manual

: June 17, 2024
: ColorKey

ColorKey CKU-5052 Mover Spot 150 Fixture User Manual

Please read these instructions carefully before use. Operating this fixture according to these instructions is important to avoid any possible damage or accidents caused by misuse.

Introduction

Package Contents

Mover Spot 150
Power Cord
4ft. DMX Cable
Hanging Bracket
Eyebolt
QR Guide

Caution! Opening this unit voids warranty. Contact Color Key for any service requests.
Warning! To avoid electrical shock, be sure to disconnect power before any service or when moving or setting up the fixture.

Service & Support

Your Color Key product includes a 2-year warranty. For technical support or to register your product, please visit https://www.colorkeyled.com/support/

You can also reach us by phone Monday thru Friday, 8:30am –5pm PST at 818-578-4030

Product Overview

Front

Moving Head
Yoke
Carrying Handle
DMX LED Indicator
Error LED Indicator
LCD Display
Menu Guide Buttons

Back

DMX Out
DMX In
Power In
Power Out
Feet for Floor Mounting

Mounting

Orientation
Mover Spot 150 may be mounted in any position; however, make sure there is adequate ventilation around the product.

Rigging

Before deciding on a location, make sure there is easy access to the product for maintenance and programming.
Make sure adequate ventilation is provided around the product.
Make sure that the structure or surface onto which you are mounting the product can support the products weight.
Mount the product securely to a rigging point, weather an elevated platform or a truss.
An eyebolt is included for the use of safety cable when hanging.
When rigging the product onto a truss, use a mounting clamp of the appropriate weight capacity.
When power linking multiple products, mount the products close enough for power linking cable to reach.
The rubber feet also serve as floor supports and allow for surface mounting.
When mounting the product on the floor, make sure that the product and cables are away from people.

Power Linking

Power Linking
Mover Spot 150 provides power linking via the outlet located on the back of the product. Up to 4 Mover Spot 150 units can be power linked.

Powering your product

Always Connect the product to a protected circuit (a circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk of shock or fire.
To eliminate unnecessary wear and improve the life of your Mover Spot 150, completely disconnect the product from power via the breaker or by unplugging it.

Display Operation

Display Operation
MENU: Access the menu/Scroll through menu options
OK: Open/Selects the current menu option
ENTER: Return to previous menu option
UP: Scroll through menu selection or parameter increase
DOWN: Scroll through menu selection or parameter decrease
DMX: Lit when receiving DMX signal
ERR: Lit when error has occurred

Main Level	Programing Level	Values
Settings	******** Mode	Console (DMX)

Gobo and Color Channel Assignments

Gobos & Color Layering
Unleash your creativity with not one, but TWO gobo wheels. The first wheel (Gobo 1) offers 7 static metal gobos, while the second wheel (Gobo 2) features 6 glass gobos that can rotate with independent channel control. Create textures and patterns like never before by layering gobos, colors, and prism effect for a truly one-of-a-kind lighting experience.

Metal Gobos (Gobo 1)

Metal Gobos

Glass Gobos (Gobo 2) – Rotating

Glass Gobos Rotating

Color Selections

DMX Values

15CH DMX values
11 0-127 Glass Gobo Rotation Manual Gobo Indexing120-255FocusFocus 130-127 Prism / Prism RotationNo Prism 140-5 Macro function (Auto Show)No function 150-25 ResetNo function

Channel	Value	Function Description
1	0-255	Dimmer
**** 2	0-10	Strobe
11-255	Strobe from Slow to Fast
3	0-255	Pan
4	0-255	Pan fine tuning
5	0-255	Tilt
6	0-255	Tilt fine tuning
**** 7	**** 0-255	**** Pan/Tilt Speed
8	Color Selection
0-4	Color Selection	Open
5-9	Open + Color 1
10-14	Color 1
15-19	Color 1 + Color 2
20-24	Color 2
25-29	Color 2 + Color 3
30-34	Color 3
35-39	Color 3 + Color4
40-44	Color 4
45-49	Color 4 + Color 5
50-54	Color 5
55-59	Color 5 + Color 6
60-64	Color 6
65-69	Color 6 + Color 7
70-74	Color 7
75-79	Color 7 + open
80-167	**CCW = Counter-Clockwise CCW Color cycling from slow to

Stand Alone Settings

To use your Mover Spot 150 without a DMX Controller, use one of the various standalone modes below.

Please note, we do not recommend using products in standalone mode that are connected to a DMX string and controller. Standalone mode may transmit DMX signals that could interfere with DMX signals from the controller.

Automatic Programs

To run the Mover Spot 150 in Automatic Mode, follow the instructions below:

Press (Menu)
Double press (OK) to select Setting
Double press (OK) to select Run Mode
Use (Up or Down) to select Auto Program 1-4
Press (OK) to make selection
Press (Enter) to return to menu

Sound Active Mode

To run the Mover Spot 150 in sound-active mode, do the following:

Press (Menu)
Double press (OK) to select Setting
Double press (OK) to select Run Mode
Use (Up or Down) to select Sound
Press (OK) to make selection
Press (Enter) to return to menu

Sound Sensitivity

To set the Sound Active sensitivity on the Mover Spot 150, follow the instructions below:

Press (Menu)
Press (OK) 3 times to enter and navigate Setting selections
Use (Up or Down) to select Sens
Press (OK) to make selection
Use (Up or Down) to select Sound Sensitivity, low- high (01-99)
Press (OK) to make selection
Press (Enter) to return to menu

Manual Mode

To operate the Mover Spot 150 manually through the menu, do the following:

Press (Menu)
Press (OK) to enter and navigate selections
Use (Up or Down) to select Test
Press (Ok)
Use (Up or Down) to select from Pan, Tilt, Gobo, Gobo Rotate, Prism, Focus, Dimmer and Strobe and other selections
Press (Ok)
Use (Up) or (Down) to increase or decrease the value of the selected function from 000- 55
Press (OK) to make selection
Press (Enter) to return to menu

Invert Pan

To set Pan orientation on the Mover Spot 150, follow the instructions below:

Press (Menu)
Press (OK) 3 times to enter and navigate Setting selections
Use (Up or Down) to select InvertPan
Press (OK) to make selection
Use (Up or Down) to turn the Pan orientation ON or OFF
Press (OK) to make selection
Press (Enter) to return to menu

Invert Tilt

To set Tilt orientation on the Mover Spot 150, do the following:

Press (Menu)
Press (OK) 3 times to enter and navigate Setting selections
Use (Up or Down) to select Invert Tilt
Press (OK) to make selection
Use (Up or Down) to turn the Tilt orientation ON or OFF
Press (OK) to make selection
Press (Enter) to return to menu

Swap Pan and Tilt

To set swap the Pan and Tilt orientation on the Mover Spot 150, do the following:

Press (Menu)
Press (OK) 3 times to enter and navigate Setting selections
Use (Up or Down) to select Swap Pan Tilt
Press (OK) to make selection
Use (Up or Down) to make the orientation ON or OFF
Press (OK) to make selection
Press (Enter) to return to menu

Screen Reverse

To set the display orientation on the Mover Spot 150, follow the instructions below:

Press (Menu)
Press (OK) to enter and navigate selections
Use (Up or Down) to select Advanced
Double Press (Ok)
Use (Up or Down) to select Screen Rot
Press (Ok) to confirm selection
Press (Enter) to return to menu

Passcode Protected Adjustments

Mover Spot 150 has a passcode protected mode that allows the user to calibrate and adjust several of the products operating parameters.

In order to access this mode, do the following:

Press (Menu)
Press (OK) to enter and navigate selections
Use (Up or Down) to select Offset
Use (Up or Down) to enter Passcode: 1234567
Select OK and Press (OK)

In this mode you can adjust the starting positions of the following:

Parameter: Function
Pan: Pan Motor
Tilt: Tilt Motor
Color: Color Wheel
Metal Gobo: Gobo Wheel
Glass Gobo: Gobo Wheel
Prism: Prism Assembly
Focus: Focus Assembly

To adjust the starting position of one of these parameters, follow the instructions below:

Access the Protected Adjustments
Use (Up) or (Down)) to select Mode
Press (OK)
Use (Up) or (Down) to increase (+127) or decrease (-128) the value of the selected function
Press (OK) to make selection
Press (Enter)

Maintenance

Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light sources life and or mechanical wear. To maintain optimum performance and minimize wear, clean your lighting products regularly after extended use. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency.

To clean the product, follow the instruction below:

Unplug the product from power.
Wait until the product is at room temperature.
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents.
Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or ISO.
Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
Softly drag any dirt or grime to the outside of the transparent surface.
Gently polish the transparent surfaces until they are free of haze and lint.

Troubleshooting

Problems: Solutions

Technical Information

90W white LED
Color wheel with 7 colors plus open
Split colors allow for up to 16 color combinations
Dual gobo wheels: 7 static metal gobos plus open and 6 glass rotating gobos plus open
Color and gobo wheels continuous scroll at variable speeds
0-100% linear dimmer
0-10Hz shutter speed
Beam Angle: 10˚
Pan: 540°/ Tilt: 270°
Motorized focus
Rotating 5 facet prism
DMX 15-channel mode
DMX: 3-pin XLR In/Out
Color LCD screen
Quick release hanging bracket
Power Supply: Power Con In + Out
Power Consumption: 120W
Dimensions: 17″ x 13″ x 12″ (423 x 322 x 297 mm)
Weight: 15 lbs. (6.8 kg)

Please note: As we continue to work towards improving our products and your experience as a user, we recommend that you check our website periodically for updates to user manuals and specifications at www.ColorKeyLED.com or you may contact us directly at info@colorkeyled.com.
Company logo