COMOMY SKUK27473 118 Retractable Baby Gates Extra Wide Instruction Manual

COMOMY SKUK27473 118 Retractable Baby Gates Extra Wide

Safety Information

WARNING To prevent serious injury or death,securely install gate or enclosure and use according to manufacturer’s instructions.
WARNING Incorrect installation can be dangerous.
WARNING Danger to older children if climbing over the product.
WARNING Do not use the safety barrier if any components are damaged or missing.
WARNING The safety barrier must not be fitted across windows.
WARNING Never install this product on glass doors.Install this product against reliable doors or walls.
WARNING If the safety barrier is used at the top of the stairs, it should not be positioned below the top level.
WARNING If the safety barrier is used at the bottom of the stairs,it should be positioned at the front of the lowest tread possible.
WARNING This satety barrier is for domestic use only.
WARNING This satetygate has a manual closing system.
WARNING Never leave the child unattended when using this product.
WARNING Children have died or been seriously injured when gates/enclosures are not securely installed.
WARNING Do not put any goods which can be grabbed by children or pets near this product to prevent injury.
WARNING Before using this product,carefully inspect for any loose parts and whether any parts need to be tightened.
WARNING Never use to keep child away from pool.
WARNING This product is intended for use with children from 6 to 24 months or small to medium pets from 4.5kg(10 lbs) up to 18kg (40 lbs).
WARNING Always check that safety barrier is correctly closed.
WARNING Use only with the locking/latching mechanism securely engaged
WARNING Gate must be installed as close to the ground as possible,as per the installation guides.
WARNING Never use with a child able to climb over or dislodge/open the gate or enclosure.
WARNING Regularly check that the safety barrier is properly installed and secure.
WARNING Always install and use as directed using all parts.
Any additional or replacement parts should be obtained from after sales support.
WARNING Barrier must be fitted between rigid surfaces such as plaster board,timber or hard wall.
WARNING This product is a deterrent and not a substitute for adult supervision. Never leave children unattended. Check the gate regularly to ensure safe usage.

What’s in the box

PARTS

• Recommended for use on wood/hard wall

8x
Expansion screw +5 spare

8x
Actual installation screws + 5 spare screws

Do not mount into dry wall without additional support.
This kit set is for dry wall installation.

10x
Drywall expansion screw

10x
Drywall installation screw

3x

Floor adhesive hooks

This gate must only be fixed to a solid and secure surface. If unsure, check with a qualified builder or trades person that the installation you intend is suitable and safe within the chosen location.

TOOLS PREPARATION:

A. Philips head screw driver

B. Pencil

C. Power drill

D. Hammer

PLEASE SELECT THE PROPER ACCESSORIES AND A SUITABLE WALL.

Install on wooden material.

Install on a hard wall.

Install on dry wall .

*Do not mount into dry wall without additional support

Do not install onto dry wood, or glass walls.

MEASUREMENT PREPARATION

Measure the door width to ensure that the gate can be installed normally.

MOUNTINGS

Gate must be installed in a structurally sound opening.Ensure mounting surface(wall,door frame,stair posts.etc) is strong.rigid and has an even surface.
Note: If using gate on stairs.it must be placed either on the top step or on the lowest step at the bottom.
Select the appropriate fixing method from the following list.

WOOD MOUNTING

Drill 5/64″(2mm) pilot holes and use the wood screws provided screwing directly into the wood.

FOR INSTALLATION

Wood Screws

HARD WALL MOUNTING BRICK

Drill 5mm (3/16″) pilot holes, insert anchor and secure with screws.
Can be used on wood walls/concrete walls.

FOR INSTALLATION

Hard /Wood Screws Anchor

DRYING WALL MOUNTING

Drill 9mm/10mm pilot holes, insert anchor and secure with screws

Attention:

1. Do not mount into dry wall without additional support
2. Note that the hole diameter cannot exceed 1 0MM

FOR INSTALLATION
Dry Wall Anchor

DRY WALL ACCESSORIES DESCRIPTION

Suitable for drilling diameter 9110mm Suitable wall thickness 8-15mm

Ideal installation effect

8-15mm wall thickness

INSTALLATION

GATE PLACEMENT

SUITABLE PLACEMENT OF GATE AND CATCH MOUNT

Inside Opening or Doorway

Outside Opening or Doorway

INSTALLATION STEPS

Note:
Thank you very much for purchasing this product. The whole installation process takes about 20 minutes. Please read the installation manual carefully find the corresponding components and select the right location to be installed. Please prepare an electric drill , a mark pen and a screw driver.

The product must be installed on the ground to better realize the separation function .

1. Main body Gate.

2. Install the two Brackets on the Gate.

3. Peel off the Paper of Adhesive tape from the two Brackets .

4. Selec1 the installation location, make sure the bottom of the main body door Gate is on the ground.

4.2 Select the installation location, make sure the bottom of main body door gate is on ground .

If there are baseboard on the wall.
pis slide lower Bracket up to the suitable position until go around the baseboard

5. Take out door gate from the 2 brackets according to the arrow .

6. Mark the holes position of the two brackets and then pull out the two brackets from wall.

7. Drill holes of with an electric drill as the marks.

8. lnsert the expansion glues to all holes

9.  Drill the two Brackets to wall as the holes.

10.  Install Gate to upper Bracket as

11. install Gate to Lower Bracket as the arrow,please make sure install Gate to upper Bracket at first then install Gate to Lower Bracket .

12. Pull the cloth horizontally to the opposite door frame to find the installation position of lower Latches.

13. Hook the lower Latch and mark the holes position of the lower Latch with a pen and make sure the gate is Vertical.

14. Pull the cloth, Let the cloth roll back.

15. Drill holes of with an electric drill as the marks

16. Insert the expansion glues to all holes

17. Drill the lower Latch to wall as the marks

18. Pull the cloth horizontally.Hook the lower latch.

19.  Press & push the button, it shows red to lock the gate.

20. Pull the cloth horizontally to the opposite door frame to find the installation position of upper Latch.

21. Hook the upper Latch and mark the holes position of the upper Latch with a pen and make sure the gate is Vertical.

22. Then Press & Push the button to unlock.

23. Pull the cloth, Let the cloth roll back.

24. Drill holes of with an electric drill as the marks

25. lnsert the expansion glues to all holes

26. Drill the upper Latch to wall as the marks

27. he installation is complete, Enjoy your gate!

28. Enjoy your gate!

ADJUSTABLE LOWER GATE MOUNT

TO REMOVE

Installation STEP FOR GATE FLOOR HOOK

This is an optional accessory: You can install this accessory on the floor, if you think the mesh is loose. If it is to prevent children from passing under the safety gate, please be sure to use this product to protect the safety of children.

Confirm fittings and prepare hole punch towels before installation.

1. Choose a suitable position on the double-layer mesh, below the mesh gate, and use hole punch to cut a small hole of about 0.35 inches.

2. Attach the white ring to the hole you just cut. Make sure the top and the bottom covers of the white ring closed tightly.

3. Put the metal ring over the white ring.

Note: Check that the top and bottom covers are tightly closed.

NO DRILLING INSTALLATION METHOD

4. Wipe the floor clean with a towel. Tear off the film on the surface of the double-sided tape and stick to the round transparent plastic part.
   
   5. Tear off the other film on the surface of the tape and stick to the ground.
   
   6. Done!

INSTALLATION method by drilling holes

4.Mark the four holes in the cloth clip with pen, drill about 4mm holes with an electric drill as the marks .

5. Insert the expansion screw to all holes,drill the four screw to ground as the holes.

6. Done!

OPERATION

HOW TO LOCK THE GATE

Note: When gate is retracting always hold the handle and guide the gate evenly back into its original position. Never let go of handle when gate is retracting.

HOW TO OPEN THE GATE

Note: When gate is retracting always hold the handle and guide the gate evenly back into its original position. Never let go of handle when gate is retracting.

CLEANING INSTRUCTIONS

Simply use a soft damp cloth to wipe gate, dry after cleaning. Do not use chemical or abrasive cleaners.

Thank you very much for choosing our products. Please read instruction manuals carefully before using this retractable safety gate.
Do not use if any part is Broken, Torn or Missing.
Please retain the instruction manual for future reference.

MANUFACTURER
SUI CHENG LIMITED
Address: Room 38, 11/F, Meeco Industrial Building, 53-55 Au Pui Wan Street, Fotan, Shatin, N.T., Hong Kong
Service :comomyofficial@gmail.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>