COMOMY 29.5-46 Baby Gate for Stairs User Manual
- June 16, 2024
- COMOMY
Table of Contents
SAFETY GATE
29.5-46 Baby Gate for Stairs
WARNING
- READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
- DO NOT CUT OFF THE BELT BEFORE INSTALLATION IS COMPLETED.
- KEEP INSTRUCTIONS FOR FUTURE USE.
- Keep small parts out of the reach of children and pets!This safety gate must not be fitted across windows or other similar openings.
- Do not cut off the belt before installation is completed!
- Adult assembly is required.Exercise care when unpacking and assembling product.
- To prevent serious injury, make sure the gate is securely installed.
- Improper installation could result in the gate becoming unstable or dislodged from the doorway.Always make sure the extension is securely attached to the gate before using.
- Always install and use all required parts as directed.
- Use only when the locking/latching mechanism is securely engageo.
- The position of the safety barrier in relation to the stairs may have an adverse effect on your child’s safety. Never use at the top of stairs without hardware mounting.
- Intended for use with children aged 6 to 24 months.
- Never use to keep children away from pools.
- Stop using when a child can climb over or dislodge the gate.
- Always close and lock the gate behind you.
- This product will not necessarily prevent all accidents. Neverleave children unattended.
- Please be aware of weak or drywall and paint, we do not recommend installation on these surfaces to avoid property damage and maintain safety.
PRODUCT & PARTS
A. Gate Door x 1
B. Extension x
C. Y-Shape Tension Bolt x2
D. Tension Bolt x 4
E. Wall Cup x4
F. Screw x4
G. Dry Wall Anchor x 4
H. Wrench x 1
I. Cable Zip Tie x1
WARNING: This package contains small parts and sharp points in
anunassembled state. Keep out of reach of children.
Adult assembly required.
SPECIAL REMINDER BEFORE INSTALLATION
Installation method Optional for Pressure Mounted and Hardware Mounted, Two installation methods, you can choose any one
Notice: Screw in mounting cups when using gate on stairs.
**** USE of the Y-shape tension bolt
- If there’s round pillars on your stairs, please USE the Y-shape tention bolt.
- Install with Y shape tention bolt when placed on a column or the install place diameter is less than 1.2″.
METHOD A : PRESSURE MOUNTED INSTALLATION
Measure the width of the opening where you intend to install the gate.
Flease refer to the following diagrams to determine the correct installation
configuration.
Rotate both of the bottom Tension Bolt as shown in the figure.
Note: Make sure the bottom of the gate frame remains completely flat on the
floor.
Next. Rotate both of the top Tension Bolt as shown in the figure.
Gate is fully pressurized and locked when the indicator turns green.
When the gate is not securely locked, the indicator light shows red.
Note: Be sure to re-check the indicator regularly and retighten the bolts
if you see any red when gate is closed.
Opening Method:
Pull the button to the right, then lift the gate panel UP to open.
Cut off the belt and test the gate:
- Push the gate to check stability.
- 0pen and close the walk through gate.
METHOD B: HARDWARE MOUNTED INSTALLATION
Pre-assemble the gate, and locate four points for hole drilling.
Hold the wall cup in position and mark the center with a pencil. Then remove
the gate.
According to your markings, drill holes in the corresponding locations, then insert the wall anchors and fix the wall cups with nails.
Place the gate in the right position for fixed adjustment, and then cut the belt.
When the door is opened to 180 degrees or less, it will start the automatic closing function.
TROUBLE SHOOTING
A: The gate are too tight, or not tight enough.
Solution: Please adjust the door clearance to 0.07in.
B: Gate is not properly aligned onto the door frame. Solution: Adjust the gate by loosening all tension bolts and reposition gate. Make sure the gate is properly aligned onto the door frame/door opening. Then re-tighten tension bolts .
C: How to make sure the gate has been completely installed correctly Solution: Please refer to the following illustration, check through the top view and side view of the gate, and install it as required by the correct illustration
D: If you need to remove the gate or reinstall it elsewhere in the future.
Solution: Before removing, tie the gate with cable zip tie to make sure the
gate is locked. Next, loosen the 4 bolts in the direction shown in Trouble
shooting and remove the gate.
Note: You must tie the gate with a tie before removing it. Otherwise, you
may need the assistance of others to help you install it again.