COMOMY J92939 4 Baby Gate with Adjustable Cat Door User Guide

COMOMY J92939 4 Baby Gate with Adjustable Cat Door

SAFETY WARNING

• Keep small parts out of the reach of children and pets! This safety gate must not be fitted across windows or other similar openings.
• Do not cut off the belt before installation is completed!
• Adult assembly is required. Exercise care when unpacking and assembling products.
• To prevent serious injury, make sure the gate is securely installed.
• Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using it.
• Always install and use all required parts as directed.
• Use only when the locking/latching mechanism is securely engaged.
• The position of the safety barrier about the stairs may hurt your child’s safety. Never use at the top of stairs without hardware mounting.
• Intended for use with children aged 6 to 24 months.
• Never use to keep children away from pools.
• Stop using it when a child can climb over or dislodge the gate.
• Always close and lock the gate behind you.
• This product will not necessarily prevent all accidents. Never leave children unattended.
• Please be aware of weak or drywall and paint, we do not recommend installation on these surfaces to avoid property damage and maintain safety.

PRODUCT & PARTS

• A. Gate Door x 1
• B. Extension X2
• C. Tension Bolt x4
• D. Wall Cup x4
• E. Screw x4
• F. Dry Wall Anchor x4
• G. Cable Zip Tie x1
• H. Y Tension Bolt x2

WARNING:
This package contains small parts and sharp points in an unassembled state. Keep out of reach of children. Adult assembly is required.

SPECIAL REMINDER BEFORE INSTALLATION

Installation method Optional for Pressure Mounted and Hardware Mounted, Two installation methods, you can choose any one.

Notice: Screw in mounting cups when using the gate on stairs.

USE of the Y-shape tension bolt.

1. If there are round pillars on your stairs, please USE the Y-shape tension bolt.
2. Install with Y shape tension bolt when placed on a column or the install place diameter is less than 1.2″.

Bottom of stairs
If the gate is used at the bottom of the stairs to prevent the child from climbing up the stairs, it must be placed on the lowest stairs.

Top of stairs
If the gate is used at the top of the stairs to prevent the child from falling down the stairs, it must be placed on any stair below the level of the top stair.

PRESSURE MOUNTED INSTALLATION

STEP 1

Measure the width of the opening where you intend to install the gate.
Please refer to the following diagrams to determine the correct installation configuration.

STEP 2

Insert 4 bolts into 4 corners of the gate/extension.

STEP 3

• Rotate both of the bottom Tension Bolt by hand as shown in the figure.
• Note: Make sure the bottom of the gate frame remains completely flat on the floor.
• Next: Rotate both of the top Tension bolts by hand as shown in the figure.

STEP 4

0.07in(The best gap is 0.078in ≈ 2mm)

If the door is too tight or not tight enough, you can continue to twist the nut and adjust the door gap to 0.07in.

STEP 5

Opening Method:
Pull the button to the right, then lift the gate panel UP to open.

Cut off the belt and test the gate:

• Push the gate to check stability.
• Open and close the walk-through gate.

HARDWARE MOUNTED INSTALLATION

STEP 1

Pre-assemble the gate, and locate four points for hole drilling. Hold the wall cup in position and mark the center with a pencil. Then remove the gate.

STEP 2

According to your markings, drill holes in the corresponding locations, then insert the wall anchors and fix the wall cups with nails.

STEP 3

Place the gate in the right position for fixed adjustment, and then cut the belt.

STEP 4

When the door is opened to 180 degrees or less, it will start the automatic closing function.

TROUBLESHOOTING

• A: The gates are too tight, or not tight enough.
  Solution:
  Please adjust the door clearance to 0.07in.

• B: The gate is not properly aligned with the door frame.
  Solution:
  Adjust the gate by loosening all tension bolts and repositioning the gate. Make sure the gate is properly aligned with the door frame/door opening. Then re-tighten the tension bolts.

• C: How to make sure the gate has been completely installed correctly
  Solution:
  Please refer to the following illustration, check through the top view and side view of the gate, and install it as required by the correct illustration.

• D: If you need to remove the gate or reinstall it elsewhere in the future.
  Solution:
  Before removing, tie the gate with a cable zip tie to make sure the gate is locked. Next, loosen the 4 bolts in the direction shown in Troubleshooting and remove the gate.
  Note: You must tie the gate with a tie before removing it. Otherwise, you may need the assistance of others to help you install it again.

OPERATION FOR ADJUSTABLE SMALL GATE

The small pet door is 7.5 x 7 inches. You can adjust its size for your pet to go through appropriately.

Operation Methods

1. UNLOCK: Twist the knob to “ “, then the small gate can be moved up and down.
2. LOCK: Twist the knob to “ “, the small gate can be locked and fixed.

WARNING

• READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THE GATE.
• DO NOT CUT OFF THE BELT BEFORE INSTALLATION IS COMPLETED.
• KEEP INSTRUCTIONS FOR FUTURE USE.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>