sauermann Si-CD3 Combustible Gas Leak Detector User Guide
- June 17, 2024
- sauermann
Table of Contents
- Gas/Refrigerant leak detectors
- Operating temperature, protection of the instruments and information
- Si-CD3 Keys
- Si-RD3 Keys
- Turn on the instruments
- Adjust the sensitivity (Si-RD3)
- Perform manual autozero (Si-RD3 only)
- Hold the measurement (Si-CD3 only)
- Display minimum and maximum values (Si-CD3 only)
- Select the measuring unit (Si-CD3 only)
- Batteries replacement
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GAS/REFRIGERANT LEAK
DETECTORS
Si-CD3 / Si-RD3
Quick Start Guide
Distributed by:
Valuetesters.com
sales@valuetesters.com
Tel: 602-795-8292
Fax: 602-795-4624
Gas/Refrigerant leak detectors
These portable instruments are used to measure and detect the following
parameters: refrigerants and combustible gases.
Symbols used
For your safety and in order to avoid any damage of the device, please
follow the procedure described in this document and read carefully the notes
preceded by the following symbol:
The following symbol will also be used in this document, please read carefully
the information notes indicated after this symbol:
Operating temperature, protection of the instruments and information
about storage
Conditions of use (°C/%RH/m): from 0 to +50 °C. In non-condensing conditions.
From 0 to 2000 m.
Protection: IP54
Storage temperature: from -20 to +80 °C.
If the instrument is stored outside the operating temperature (for example in
a van, a warehouse…), please wait for 10 minutes in its operating temperature
before start using it.
Si-CD3 Keys
| KEY | FUNCTION |
|---|---|
| ON-OFF/Esc. Turn the instrument on/off and allow to back to previous |
selection.
| OK key. Confirm selection
| Select key. Navigate throught the menu
| HOLD/min/max key. Hold value, and display minimum and maximum values
| Backlight key. Activate/Deactivate the backlight
Si-RD3 Keys
| KEY | FUNCTION |
|---|---|
| ON-OFF key. Turn the instrument on/off. | |
| Beep key. Enable or disable the audible signal. | |
| Sens key. Set the sensitivity and allow to perform an autozero. |
Turn on the instruments
Switch on the instrument by pressing briefly on “On/Off/Esc” (Si-CD3) or
“On/Off” (Si-RD3).
Si-CD3: when it turns on, the device emits a beep then performs a pre-
heating phase. This phase lasts 60 seconds. The count of this pre-heating time
displays on screen.
Si-RD3: when it turns on, the pre-heating phase of the sensor begins. This
phase lasts 60 seconds. During this phase, all the visualisation leds of
thresholds light one after the other.
A few second before the end of the pre-heating phase, all the leds blinks at
the same time.
Adjust the sensitivity (Si-RD3)
If the gas concentration is high, press “Sens.” key to set the sensitivity and
like this to get a better identification of the leak source. Please see in the
table below about the three different sensitivities.
Press “Sens.” key to adjust the sensitivity of the device.
| Mode | Indicative measuring range (g/year) | Visual alarm |
|---|---|---|
| Low sensitivity (“L” on the device) | From 0 to 300 g/year | All the LEDs (8) |
for 300 g/year
Normal sensitivity (“M” on the device)| From 0 to 30 g/year| All the LEDs (8)
for 30 g/year
High sensitivity (“H” on the device)| From 0 to 3 g/year| All the LEDs (8) for
3 g/year
Perform manual autozero (Si-RD3 only)
During measurement:
Press at least 3 s key to perform an autozero.
The “Autozero” led lights on.
Hold the measurement (Si-CD3 only)
During measurement, press briefly on “Hold/min/max” to hold measurement:
“Hold” appears on the screen and measurement is fixed.
Briefly press “On-Off/Esc” to exit the Hold function.
Display minimum and maximum values (Si-CD3 only)
When measurement is hold:
Press “Hold/min/max”: maximum value measured since the last questioning is
displayed on the top of the screen and minimum value measured since the last
questioning is displayed on the bottom of the screen.
Press “On-Off/Esc” to return to the measurement display.
Select the measuring unit (Si-CD3 only)
The device is on and displays the measurement.
Press “Select”.
“UNIT” blinks on screen.
Press OK.
The unit currently used blinks on screen.
Press “Select” until the desired unit appears : ppm, %VOL, %LEL.
Press OK to validate the unit selection.
“UNIT” blinks on screen.
Press “On-Off/Esc” to return to the measurement display.
Batteries replacement
The instrument is OFF.
Remove the battery cover at the back.
Replace the 4 alkaline batteries LR03 AAA 1.5 V respecting the polarity.
Put back the battery cover.
To ensure safety, replace batteries with the same type.
Not doing so might lead to explosion. Dispose of used batteries according to
instructions.
Download the full manualhttps://sauermanngroup.com/en-INT/measuring-
instruments/portable-instruments
Sauermann Industrie
ZA Bernard Moulinet
24700 Montpon
France T. +33 (0)5 53 80 85 00
services@sauermanngroup.com
Sauermann NA
140 Fell Court, Ste. 302
Hauppauge, New York 11788
T. (+1) 631-234-7600
F. (+1) 631-234-7605
info.usa@sauermanngroup.com
Sauermann GmbH
Leibnizstraße 6
D – 74211 Leingarten
T. +49 (0)7131/399990
F. +49 (0)7131/399992
info.germany@sauermanngroup.com|
Sauermann UK
Units 7-9, Trident Business Park
Amy Johnson Way
Blackpool – FY4 2RP
T. +44 (0) 870 950 6378
F. +44 (0) 870 950 6379
info.uk@sauermanngroup.com
Sauermann Italia srl S.U
Via Golini 61/10
40024 Castel S.Pietro Terme (BO)
T. (+39)-051-6951033
F. (+39)-051-942254
info.italy@sauermanngroup.com
Sauermann Ibérica
C/Albert Einstein 33.
Planta 3. P. I. Santa Margarida II08223
Terrassa(Spain)
T.+34 931 016 975
info.spain@sauermanngroup.com|
Sauermann Australia
1/36 Campbell Avenue, Cromer ,2099,
NSW, Sydney
T. (+612) 8880 4631
sauermannpumps.com.au
Sauermann China
Room 401-6, Building 8, No. 3000 Longdong
Ave. Pudong New District
Shanghai 201203/R.P. China
T. +86-21-61001877
F. +86-21-61001870
info.china@sauermanngroup.com
---|---|---
Customer service portalhttps://sauermann-en.custhelp.com
Valuetesters.com
sales@valuetesters.com
QSG_HV A CR_Si-CD3-Si-RD3 – 07/10/2022 – Non-contractual document
W e reserve the right to modify the characteristics of our products without
prior notice
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>