iPOWER GXS4900RC Remote Control Generator User Guide

iPOWER GXS4900RC Remote Control Generator

Specifications:

• Model : GXS4900RC
• Power Output : [Insert power output]
• Fuel Type: [Insert fuel type]
• Engine Type: [Insert engine type]
• Weight : [Insert weight]

Product Usage Instructions

Unpack Generator:
Remove the generator, accessories, inserts, and literature from the carton. If any item is missing or damaged, contact our productservice department at 855-888-3598.

Install the Wheel Kit:
Follow the instructions provided in the manual to install the wheel kit for easy portability.

Add Lubricant and Fuel:
Ensure you add the recommended lubricant and fuel to the generator. Follow the guidelines provided in the manual for the correct ratios and types of lubricant and fuel.

Adjust Shock-absorbing Seat:
Before operating the generator, adjust the shock-absorbing seat for proper clearance. Loosen the lock nut, adjust the seat to maintain a 3mm gap between the seat and motor bracket, then re-tighten the lock nut.

FAQ

• Can I use the generator indoors?
  No, using the generator indoors can be extremely dangerous as generator exhaust contains carbon monoxide. Always operate the generator outside and far away from any living spaces.

• How do I start the generator?
  To start the generator, follow the instructions to turn the starting dial switch to the correct position. Depending on the model, you may need to use the remote start or recoil start method as outlined in the manual.

Included Items

WARNING
This Quick Reference Guide is not substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and underdstand the operator’s manual before using this product. All pages references to the operator’s manual.

Usage Instructions

Install the wheel kit

• Slide the axle pin(B) through the wheel(C), flat washer(D) and mount point on the frame(E). Secure them with cotter pin(F),then assemble Cap(A) to Wheel(C).
• Attach the support leg(H) to the generator frame with flange bolt(G)(M8X16) and flange lock nut(I)(M8).

Battery Cable Connection
A quick connect battery plug is pre-installed on the battery.Cut the cable tie securing the plugs and push two halves A and B firmly to connect them.

Add Lubricant and Fuel

• Use clean / fresh regular UNLEADED gasoline with a minimum 87 octane.
• Use clean / fresh regular UNLEADED gasoline with a minimum 87 octane.

Adjust Shock-absorbing Seat
Before operating the generator, the shock-absorbing seat (cushion) must be adjusted for proper clearance. Loosen the lock nut and adjust the shock- absorbing seat so there is a 3mm gap between the top of the seat and the bottom of the motor bracket. Re-tighten the lock nut.

Removal of Shipping Support Brackets
Remove the bolt (E) with double open wrench (8mm-10mm) (B). Remove the bolt (F) and nut (C) with double open wrench (13mm-15mm) (A) and double open wrench (8mm-10mm) (B).

CAUTION Failure to remove the support brackets, can result in damage to your generator, possible personal injury and avoid your warranty.

Start Generator
Move generator outside to a flat, level surface, away from doors, windows and vents.
DANGER

• Using a generator indoors can kill you in minutes. Generator exhaust contains carbon monoxide. This is a poison you cannot see or smell.
• never use inside a home or garage, even if doors and windows are open.
• only use outside and far away from windows, doors and vents.
• avoid other generator hazards. Read manual before use.
  WARNING Do not overload generator or electrical cords. Consult operation manual.

1. Add gasoline to the fuel tank.

2. Turn the starting dial switch to the position.

3. Turn the battery switch to the “ON”(l) position.

4. Remote Start
   Turn and hold the REMOTE START switch for 5 seconds until the engine start.
   Electric Start
   Turn and hold the ENGINE START/STOP switch for 5 seconds until the engine start.

Recoil Start

  * Move the choke lever to the “START” position.
  * Pull recoil starter slowly until resistance is felt, then pull rapidly.
  * Move the chock lever to the “RUN” position.

5. Plug in items to be powered, using only grounded extension cords.

Shutdown and Storage

1. Remove any load from the generator.

2.  Push STOP on the remote start key fob for 3second.
   Push and hold the START/STOP button for 3 second.

3. Turn the starting dial switch to the position.

4. Turn off the battery switch to “OFF” position.

If generator is to be stored for longer than 30 days, refer to the operator’s manual for further Instruction.

Questions?
Call 855-888-3598 or email support@a-ipower.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>