A-iPOWER PWE2002 Electric Pressure Washer Owner’s Manual

A-iPOWER PWE2002 Electric Pressure Washer

Product Information

Specifications:

• Model Number: PWE2002
• Water Compatibility: Cold water only
• Intended Use: Outdoor, Household
• Additional Items: Nozzle Selection Included, Turbo Nozzle, Open End Wrench, Nozzle Cleaning Tool, Allen Wrench

Product Usage Instructions

Assembly:

1. Insert the axle through the frame, wheels, and flat washer. Use the open-end wrench to tighten the nut securely and push the wheel caps into position.
2. Use the Allen wrench to hold the internal bolt inside the power cord holder. Remove the nut and screw the internal bolt into the handle tube threaded hole. Tighten securely.
3. Slide the handle onto the frame until it contacts buttons.
4. Install the gun holder to the handle by tightening the knob nut manually.
5. Install the pressure hose hanger to the back of the storage panel.

Operation:

6. Insert the water supply hose into the water inlet. Thread the collar on the inlet onto the garden hose. Tighten securely. Ensure a minimum flow rate of three gallons per minute at 20 PSI.
7. Pull the collar on the high-pressure hose back and push the hose fitting into the threaded outlet on the pressure washer. Screw the collar onto the outlet and tighten securely.
8. Pull the collar on the spray gun hose back and push the hose fitting into the threaded outlet on the spray gun. Screw the collar onto the outlet and tighten securely.
9. Attach a nozzle to the wand by pulling back the quick connect collar and pushing the nozzle onto the end of the wand. Ensure the quick connect collar locks the nozzle in place.
10. Connect to the water supply and turn on.

Frequently Asked Questions

• Q: Can this pressure washer be used with hot water?
  • A: No, this pressure washer is designed for cold water use only.
• Q: What should I do if I encounter a leak in one of the connections?
  • A: Check that all connections are securely tightened. If a leak persists, turn off the pressure washer and fix the connection before resuming use.
• Q: Can I use this pressure washer indoors?
  • A: No, this pressure washer is intended for outdoor use only.

“`

PWE2002 REV_00

10 11 13
14
18 19
21 22
23

PWE2002

Nozzle Selection Included

0°,

and Turbo

Owner’s Manual
Quick Start Guide
Open End Wrench, Nozzle Cleaning Tool and Allen Wrench

For cold water only. Outdoor use only. Household use only.
Caution If connection is made to a potable water system, the system should be
protected against backflow.

Caution If connected to circuit protected by fuses, use time delay fuse marked “D”

Risk of Explosion DO NOT spray flammable liquids.

DO NOT discharge stream at persons.

9
WARNING
Risk of electrocution 1. Inspect cord before using. Do not use lf cord ls damaged. 2. Keep all connections dry and off the ground. 3. Do not touch plug with wet hands. 4. Double insulated – when servicing use only ldentent parts. 5. This product is provided with a ground fault circuit interrupter built into the power cord plug. If
replacement of the plug or cord ls needed, use only ldentical replacement parts. 6. Do not spray elecrical apparatus and wiring. 7. Read instruction manual before using. Do not remove this tag.

10

A

G B

C

L

H

M

N K I

D E
J F
T

OP

Q

A – Handle B – Nozzles C – Storage Panel D – Water Inlet E – Water Outlet

R

S

F – Detergent Tank G – Trigger H – Spray Gun/Wand I – Push Botton J – Wheel

K – Power Cord L – Hose Hanger M – High Pressure Hose N – Power Cord Holder O – Open End Wrench

P – Nozzle Cleaning Tool Q – Allen Wrench R – Owner’s Manual S – Quick Start Guide T – Turbo Nozzle

11

1. Insert axle through frame, wheels and flat washer, then use open end wrench to tighten nut securely. Finally push wheel caps in position. See Figure A.

4. Install gun holder to the handle by tightening knob nut manually. See Figure D.

Wheel Cap

Axle

Open End Wrench

Wheel

Nut Flat Washer

2. Use allen wrench to hold internal bolt inside power cord holder, and remove nut 1. Then use allen wrench to screw internal bolt into handle tube threaded hole, and tighten it securely. See Figure B.

Power Cord Holder

Gun Holder Knob Nut
5. Install pressure hose hanger to back of storage panel. See Figure E.
Figure E Hose Hanger

3. Slide the handle onto the frame until it contacts buttons. See Figure C.
Handle

6. Insert water supply hose into water inlet. Thread collar on inlet onto garden hose. Tighten securely. See Figure F. Water source must be able to provide a minimum of three gallons of clean, cold water per minute at 20PSI. Only use a 5/8″ inner diameter, or larger hose that is rated to meet this capacity.
F
Water Inlet Collar

Frame

Water Supply Hose (Garden Hose)

12

7. Pull collar on the high pressure hose back and push hose fitting into threaded outlet on pressure washer. Screw collar onto outlet and tighten securely. See Figure G.
Figure G

10. Attach nozzle to wand by pulling back quick connect collar and pushing nozzle onto end of the wand. Make sure quick connect collar locks the nozzle in place. See Figure J.
Figure J

Collar

High Pressure Hose
8. Pull collar on spray gun hose back and push hose fitting into threaded outlet on spray gun. Screw collar onto outlet and tighten securely. See Figure H.
Figure H
Gun

11. Connect to water supply & turn on. See Figure K.
See Figure K

Inlet Coupler

Collar Spray Gun Hose

9. Push the wand into spray gun and turn to tighten. Do not over tighten. See Figure I.
Figure I

12. Unlock trigger, then pull trigger to release pressure. See Figure L.
See Figure L

13

14
On the top of the product is the MAIN ON / OFF push button switch (See Figure I). This switch works in conjunction with the AUTO ON / OFF switch built into the product. The AUTO switch turns on and off when the trigger of the gun is squeezed and / or released. Because of this, the system can have pressure, even when the motor is not running. Always use caution around the pressure washer.
Push

15

Soap Turbo Nozzle

SOAP
Turbo Nozzle
0° Nozzle – Red: This nozzle delivers a pinpoint stream of pressurized water and is extremely powerful. Use it for the toughest cleaning jobs, although It covers only a small area. This nozzle should only be directed at surfaces that can withstand intense high pressure such as metal or concrete. Do not use this nozzle to clean wood or soft surfaces. Soap Nozzle: This nozzle is used to apply special chemicals and cleaning solutions. This nozzle produces the weakest pressure stream of the nozzles.

Turbo Nozzle: High-speed rotation generates strong pressurized jet water with an angle of 15 °. The turbocharger nozzle can save 50% of energy, 30% of water, 50% of cleaning agent, and increase 50% of work efficiency, which is extremely economical.

NOTICE:

1. Not all models come with all nozzles described in this section. Use only theinformation

pertaining to the nozzles supplied with your product.

2. If the nozzle tip is found blocked by debris, use the nozzle cleaning tool to poke it

several times until the water flows out normally.

Nozzle Cleaning Tool

16

17

push

Push

to off position.

18

19

20

6
5
4 11 39 45
46 1 44
2 3

C US

1875W

ELEGRP 125VAC 60HZ

15A

35 34

33

32

38

14 24

37

10

7 8 9 24

21

31

30

29

28 27

1.000
12 13

42 41 40 26 25
18
24

14 15

20 21

19 23

16

22

17

43

Parts List

NO. Part Number Description

Qty.

1 20048-00172-00 High pressure hose

1

2 20091-00038-01 Spray gun

1

3 20092-00026-00 Spray wand

1

4 20196-04929-00 Harness

1

5 33013-00331-00 Upper shell

1

6 31026-00265-00 ON/OFF push button switch

1

7 70009-00860-00 Water inlet union nut

1

8 20100-00588-00 Motor pump

1

9 30117-00014-00 Phillips pan head tapping screw 8

10 33013-00334-00 Pump head clip

2

11 33171-00038-00 Baffle

1

12 20131-00027-00 Detergent tank cap

1

13 20130-00501-00 Detergent tank

1

14 30114-00014-01 Hexagon socket head bolt

7

15 34030-00207-00 Shock absorbing pad

1

16 34028-00003-00 Siphon

0.5

17 34024-00004-00 Metal harness clip

1

18 20090-01459-00 Frame

1

19 30114-00016-01 Hexagon socket head bolt

6

20 30136-00117-00 Flat washer

2

21 30150-00070-00 Circlip for shaft

2

22 20134-00179-00 Wheels

2

23 34031-00094-00 Axel

1

24 30136-00027-00 Flat washer

8

25 30117-00010-00 Phillips pan head tapping screw 6

26 34024-00093-00 V-shaped clip

2

27 20184-00039-00 Power cord holder

2

28 34035-00068-00 Spray gun holder

1

29 20135-00347-00 Handle tube

1

30 33015-00145-00 Foam grip

1

31 33624-00036-00 Hose hanger

1

32 34036-00104-00 0° nozzle

1

33 34036-00129-00 25° nozzle

1

34 34036-00130-00 40° nozzle

1

35 34036-00131-00 Soap nozzle

1

36 33275-00047-00 Nozzle grommet

4

37 33089-00286-00 Storage panel

2

38 33013-00377-00 Power cord fixing clip

2

NO. Part Number

Description

39 33013-00332-00 Base plate

40 70009-00920-00 Plastic rib

41 70009-00921-00 Plastic rib

42 70009-00922-00 Plastic rib

43 34024-00062-00 Clamp

44 34036-00127-00 Turbo nozzle

45 30136-00126-00 Flat washer

46 30125-00027-00 Nut

22
Qty. 1 1 1 1 2 1 1 1

23

24

25

Made in Vietnam

Made in Vietnam
32082-06484-00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>