BIOGENIS OptonicaLED Hydrogen Water Bottle User Manual

BIOGENIS OptonicaLED Hydrogen Water Bottle

Specifications

• Product Name: HYDROGEN WATER BOTTLE
• Power Adapter: 5V/2A

Product Information

The HYDROGEN WATER BOTTLE consists of the following components:

• Cover
• User Manual
• Body
• Base Switch
• Base

FAQ

• Q: Can I use carbonated beverages with the HYDROGEN WATER BOTTLE?
• A: No, using carbonated beverages is forbidden due to the risk of explosion from high internal pressure.

PRODUCT STRUCTURE

NOTICE

1. Please use a power adapter of 5V/ 2A, do not use the unmatched power adapter, to avoid product damage or potential safety hazards.
2. Please stay away from heat and fire.
3. To avoid damage to the product, please fo not fisassemble or repair it.
4. To avoid mechanical failure due to water penetration, please fo not wash or immerse in water directly.
5. Machine electrolysis and after electrolysis, do not lay flat or upside down.
6. The product can not be soaked in water, please wipe it dry promptly if poured water on the body accidentally, to avoid damage to the product.
7. Using carbonated beverages to generate high concentrations hydrogen water is forbidden, because internal pressure is too high, and there is an explosion risk.
8. Using high-concentration minerals water is forbidden, which may lead to the proton membrane channel is blocked, affecting the effect of hydrogen production.
9. Using tea water is forbidden, it may generate tea-scale minerals or other substances.
10. Applicable water and temperature: pure water, and warm water at 5ºC-60ºC.
11. Hydrogen generated by this product is mostly soluble in water, but it is recommended to tighten the cover when making hydrogen. Hydrogen dissolved in water will gradually escape over time, therefore, it is recommended to drink within 30 minutes after hydrogen is generated. To ensure the high concentration of hydrogen water, it is recommended to generate again when place for more than 30 minutes.
12. If it will not be used for a long time, please add the proper amount of purified water into the cup, keep the membrane electrode moist, and clean it with clean water before using it again.
13. Since the proton membrane needs to be stored in a humid environment, it is normal to have a water mist.
14. After completion of electrolysis, please unscrew the bottle cover to relieve pressure to prevent water leakage at the bottom of the bottle under high pressure.
15. Do not electrolyze without water in the bottle.
16. There is a moisturizing plug inside the bottle. When using the bottle for the first time, unscrew the bottle body and the base, take out the moisturizing plug from the base, and screw the bottle body and base back to use.
17. Do not exceed the maximum water level when adding water to the bottle.

USAGE METHODS AND PROCEDURES

For first-time use, clean the bottle and then pour purified water below 60ºC into the cup, soak for 10 minutes, electrolysis 1-2 times and then use.

Start-up
Double click the ” ”power/ mode button, and “di” will be heard for the start- up of the machine. Power left and working time will be shown on the screen.

Double click

Choosing working time
Mode of 5min
When the screen displays 5min and if the “ ” power/ mode button is not tapped within 2s, the LED in the cup will light up, and the screen displays the dynamic dot matrix flashes, which indicates that the electrolysis is in progress.

Mode of min
When the screen displays 5min tap the “ ” power/ mode button again to switch to the working mode for 10 min.

Switching of time display/ PPB display
During operation, tap the “ ” power/ mode button to switch between the time display and the PPB display.

Completion
At the end of electrolysis, the hydrogen water bottle makes a “di” and then enters into the status of the shutdown.

Shutdown after start-up
If you need to terminate the work or turn off the power supply during startup, please tap the “ ” power/ mode button for about 2 seconds.
The power will be turned off automatically when the screen goes out.

Low battery
Double click the “ ” power/ mode button, “di” is heard to start the machine, and the screen will show the power left. When the power on the screen shows 1 bar, it means the product is low in power, reminding the user to charge the product in time.

Double click

The product is completely powerless
Double click the “ ” power/ mode button, “di” is heard to start the machine, and the screen will show the power left. When the lightning icon appears on the screen, it means that the product is completely out of power and the product cannot work.

Double click

Product charging
Please use a 5V/2A charger to charge the product. When charging, the battery symbol on the screen will increase one by one, and cycle back and forth. When the battery symbol on the screen shows that the battery symbol is full and no longer jumps, it means that the product is fully charged.

PRODUCT TECHNICAL INDICATORS

interface

Product Size| Φ60×230| The diameter is 60 and the height is 230.
Hydrogen content in 5min| 1600PPB|
Hydrogen content in 10min| 3000PPB|
Working times in 5 Min. upon full-charge| About 15 times|
Working times in 10 Min. upon full-charge| About 8 times|

PACKAGE INCLUDING

MAINTENANCE

1. Wipe the product appearance with a wet soft cloth, and remove the foreign matter inside the water bottle and on the electrode.
2. If the product will not be used for a long time, please add a small amount of purified water into the bottle to keep the proton membrane in a moist state.
3. After each work, unscrew the bottle cover to relieve the pressure of the bottle.

COMMON TROUBLESHOOTING

If there are any anomalies during the use of the product, please check the following possible causes and correct them. If it still exists, please contact the dealer or company.

There are no bubbles or small amounts of bubbles when the cup is used

for the first time

|

1. Proton membrane is dry or not activated.

2. Add purified water, soak for 10 minutes, and electrolyze for several times to see if the amount of bubbles increases.
Amount of the bubble in the cup during the operation is reduced|

It is a normal phenomenon. The inner pressure of the cup increases as the electrolysis progresses so that the amount of bubbles will be reduced accordingly.

Water seepage at the bottom of the cup

|

The cup cover has not been unscrewed after electrolyze to relieve the pressure inside the cup. It is recommended to unscrew the cover to relieve pressure after each electrolyze, even if you do not drink the water.

CONTACT

• IMPORTER: Prima Group 2004 LTD, Bulgaria, 1784 Sofia,
• Mladost 1, bl. 144, Ground Floor; Phone: +359 2 988 45 72;

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>