CORBETT 417-04-VPB Selene Four Light Wall Sconce Instruction Manual
- June 13, 2024
- CORBETT
Table of Contents
CORBETT 417-04-VPB Selene Four Light Wall Sconce
Product Information
Part Name | Part Number |
---|---|
Mounting Plate (A) | Not specified |
Mounting Screws (B) | Not specified |
Ground Screw (C) | Not specified |
Wire Nut (D) | Not specified |
Bulb (I) | Not specified |
Alabaster A | Not specified |
Alabaster B | Not specified |
Alabaster C | Not specified |
Alabaster D | Not specified |
Product Usage Instructions
- Start by mounting the Mounting Plate (A) using the provided Mounting Screws (B).
- Secure the fixture to the wall using Wall Anchors (F).
- Connect the Ground Screw (C) to ensure proper grounding. Never connect the ground wire to the hot wire to avoid serious injury or death.
- Use a Wire Nut (D) to securely connect the wires. Ensure there are no exposed wires or strands that could cause a dangerous short circuit.
- Never reverse hot and neutral wires as it could result in serious injury or death.
- Assemble the Fixture (H) onto the Mounting Plate (A) using the Set Screws.
- Install the recommended 8-watt Type B Lamp (I) into the Socket. Do not exceed the recommended wattage.
- Attach the Alabaster A, B, C, or D components (K, L, M, N) as needed using the Nut (J).
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.
- THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.
WASH HANDS AFTER USE
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND.
- INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
Parts
PART(S) | REPLACEMENT PART NAME | NUMBER |
---|---|---|
A,B,C,D,E,F,G | HARDWARE KIT | HDW-417-04 |
J | BALL NUT | NUT-417-04 |
K | ALABASTER A | ALA-417-04-A |
L | ALABASTER B | ALA-417-04-B |
M | ALABASTER C | ALA-417-04-C |
N | ALABASTER D | ALA-417-04-D |
FIXTURE INSTALLATION
- Determine the location for the lamp. Using the MOUNTING PLATE (A) as a template, mark the location of the holes for the WALL ANCHORS (F)
- Drill the appropriate size holes for the WALL ANCHORS (F). (the holes should be slightly smaller than the size of the anchors.) Install the wall anchors to the hole.
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard junction box. The junction box must be securely mounted to the structure of the building. Screw in the WOOD SCREW (G) to the anchors.
- Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE! FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting I” below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
- Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
- Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) and secure with the SET SCREWS (E).
- Screw the BULB (I) up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR 8 WATT TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE!
- Attach the ALABASTER A, B, C, D (K,L,M,N) to the FIXTURE ASSEMBLY (H) and secure with the BALL NUT (J).
- Restore power to the outlet at the breaker or fuse box.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>