Midea MWMWT080CR1A 8,000 BTU Window Air Conditioner With Remote Owner’s Manual
- June 9, 2024
- Midea
Table of Contents
MWMWT080CR1A
WINDOW AIR CONDITIONER
MWMWT080CR1A 8,000 BTU Window Air Conditioner With Remote
Free 3 months extension of the original limited warranty period! Simply text
a picture of your proof of purchase to:
1-844-224-1614
The warranty extension is for the three months immediately following the completion of the product’s original warranty period. Individuals do not need to register the product in order to get all the rights and remedies of registered owners under the original limited warranty.
LIMITED WARRENTY 1 Year
Customer Service : 1-866-646-4332
Our customer service staff is available to help you. For any problem with your
purchase, or to receive further information about this product, please call
our toll-free number.
SAVE THIS MANUAL
Keep this manual and the original sales invoice in a safe, dry place for
future reference.
SAFETY PRECAUTIONS
To prevent injury to the user or other people and property damage, the
instructions shown here must be followed. Incorrect operation due to ignoring
of instructions may cause harm or damage. The level of risk is shown by the
following indications.
WARNING
This symbol indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
This symbol indicates a hazardous situation, which, if not avoided, could
result in minor or moderate injury.
NOTICE
This symbol addresses practices not related to physical injury.
WARNING
-
Be sure the air conditioner has been securely and correctly installed according to the installation instructions in this manual. Save this manual for possible future use in removing or installing this unit.
-
Plug in power cord plug properly.
Otherwise, it may cause electric shock or fire due to excess heat generation. -
Do not modify power cord length or share the outlet with other appliances as it may cause electric shock or fire due to overheating.
-
Always ensure effective grounding.
Incorrect grounding may cause electric shock. -
Unplug the unit if you notice unusual sounds or smells or smoke coming from it. A damaged product may cause fire and electric shock.
-
Ventilate room before operating the air conditioner if there is a gas leakage from another appliance.
-
Do not operate or stop the unit by inserting or pulling out the power cord plug.
-
Do not operate with wet hands or in very humid environments.
It may cause electric shock. -
Do not allow water to come into contact with any electric parts.
It may cause failure or electric shock. -
Do not use the socket if it is loose or damaged.
It may cause fire and electric shock. -
Do not use or keep the power cord close to heating appliances.
It may cause fire and electric shock. -
Do not use any devices or materials for installation that are not recommended in this manual.
WARNING
-
Do not disassemble or modify unit.
It may cause failure and electric shock. -
Do not damage or use an alternate power cord.
It may cause fire and electric shock.
If the power cord is damaged, it must be replaced by the manufacturer or an authorized service center or a similarly qualified person in order to avoid a hazard. -
Do not direct airflow straight into persons to avoid possible health hazard.
-
Do not open the unit during operation.
It may cause electric shock. -
Do not use the power cord near flammable gas or combustibles, such as gasoline, benzene, thinner, etc.
It may cause an explosion or fire. -
Do not let children hang on the air conditioner or bracket.
A serious injury may occur. -
Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug.
Do not remove any prongs from the power cord. -
Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.
-
Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle.
Ensure the receptacle is accessible after the unit installation. -
Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the cabinet and behind the grille.
-
Do not drink the drain water. It may contain mold and bacteria that can lead to death if ingested.
CAUTION
-
When the air filter is to be removed, do not touch the metal parts of the unit. It may cause injury.
-
When the unit needs cleaning, switch off, and turn off the circuit breaker.
Do not clean unit when power is on as it may cause fire, electric shock or injury. -
Do not place obstacles around air inlets or inside of air outlet.
It may cause failure or accident. -
Clean with a soft cloth only. Do not use strong detergents that contain wax or thinners as it may damage the product.
-
Use caution when unpacking and installing. Sharp edges could cause injury.
CAUTION
-
Do not clean the air conditioner with water.
Water may enter the unit and degrade the insulation which could lead to electric shock. -
Do not put a pet or house plant where it will be exposed to direct air flow.
This could injure the pet or harm the plant. -
Hold the plug by the head of the power plug when taking it out.
Otherwise, it may cause electric shock and damage. -
Ensure that the installation is properly secured to prevent the product from potentially falling.
-
Do not place heavy objects on the power cord and ensure that the cord is not compressed.
Otherwise, there is danger of fire or electric shock. -
If water is spilled on the unit, turn off the unit and switch off the circuit breaker.
Isolate supply by taking the power-plug out and contact a qualified service technician. -
Do not use near gas stove or other gas burning appliances, as air flow may affect gas combustion.
-
Do not use for any purpose other than room comfort.
Do not use this air conditioner to preserve precision devices, food, pets, plants, and art objects. It may cause deterioration. -
Turn off the main power switch if the unit is not to be used for an extended time.
-
Always insert the filters securely. Clean filter once every two weeks.
Operation without filters may cause failure.
Operation of Current Device
The power supply cord contains a current measuring device that detects
damage to the power cord. Test your power supply cord as follows:
- Plug in the air conditioner.
- The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out.
- Press the RESET Button. You will notice a click as the button engages.
- The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head.)
NOTICE
The power supply cord with this air conditioner contains a current detection
device designed to reduce the risk of fire.
In the event that the power supply cord is damaged, it can not be repaired. It
must be replaced with a cord from the manufacturer.
NOTICE
- Do not use this device to turn the unit on or off.
- Always make sure the RESET button is pushed in for correct operation.
- The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it can not be reset. Please contact Customer Service.
EXPLANATION OF SYMBOLS DISPLAYED ON THE UNIT
**| WARNING| This symbol shows that this appliance used a flammable
refrigerant. If the refrigerant is leaked and exposed to an
external ignition source, there is a risk of fire.
---|---|---
**| CAUTION| This symbol shows that the operation manual should be
read carefully.
| CAUTION| This symbol shows that a service personnel should be handling
this equipment with reference to the installation
manual.
**| CAUTION**| This symbol shows that information is available such as
the operating manual or installation manual.
WARNING
- Do not try to accelerate the defrosting process or methods of cleaning that are not recommended by the manufacturer.
- The appliance shall be stored in a room without a continuously operating ignition source (for example, open flames or an operating gas appliance) or an ignition source (for example, an operating electric heater) close to the appliance. The appliance shall also be stored in a room without ignition sources.
- Do not pierce or burn.
- Be aware that the refrigerants may not contain an odor.
- Keep ventilation openings clear of obstruction.
- Unit is only to be serviced by a Midea authorized servicer, please call Customer Service at 1-866-646-4332 for support.
- Flammable refrigerant R32 is used within air conditioner. Please follow the instructions carefully to handle, install, clean, and service the air conditioner to avoid damage or hazard. Do not dispose of air conditioner in regular trash. Contact qualified agency for proper disposal.
- No open fire or devices that generate spark/arcing shall be around the air conditioner to avoid causing ignition of the flammable refrigerant used. Please follow the instructions carefully to store or maintain the air conditioner to prevent mechanical damage from occurring.
Caution: Risk of fire/flammable materials
(Required for R32/R290 units only)
IMPORTANTNOTE: Read this manual carefully before installing or operating
your new air conditioning unit. Make sure to save this manual for future
reference.
OPERATING INSTRUCTIONS
Normal Sounds
NOTICE
All the illustrations in this manual are for explanation purpose only. The
actual installation may vary.
Air Conditioner Operation
WARNING
To reduce the risk of fire, electrical shock, or injury to people or property,
read the SAFETY PRECAUTIONS before operating this appliance.
NOTICE
Always wait 3 minutes when turning the unit off and then on again, or when
changing from cool to fan and back to cool. This prevents compressor from
overheating and possible tripping.
TO BEGIN OPERATING THE AIR CONDITIONER, FOLLOW THESE STEPS:
- Set the temperature to the coldest setting.
- Set the control to HIGH COOL.
- Adjust the louver for comfortable air flow (see Air Directional Louvers).
- Once the room feels cool, adjust to the temperature you find most comfortable.
- Make sure that the air flow inside and outside are not obstructed by anything.
- This air conditioner is designed to be operated under the following conditions:
Cooling Operation | Outdoor temp.: 64-109°F/18-43°C |
---|
Indoor temp.: 62-90°F/17-32°C
NOTICE
- The relative humidity of room should be less than 80%. If the unit is used in a condition with a relative humidity over 80%, there will be condensed water on the surface of the unit.
- Performance may be reduced outside of these operating temperatures.
Before you begin, thoroughly familiarize yourself with the control panel as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control panel alone or with the Remote Control.
Air Conditioner Features
Electronic Control Operating Instructions
Before you begin, thoroughly familiarize yourself with the control panel as
shown below and all its functions, then follow the symbol for the functions
you desire. The unit can be controlled by the unit control alone or with the
remote controller.
TO TURN UNIT ON OR OFF:
Press Power button to turn unit on or off.
NOTICE
The unit will automatically initiate the Energy Saver function under Cool,
Dry, Auto (only Auto-Cooling and Auto-Fan) modes.
TO CHANGE TEMPERATURE SETTING:
Press UP/DOWN button to change temperature setting.
NOTICE
Press or hold either ( ) or DOWN ( ) button until the desired temperature is
seen on the display.
This temperature will be automatically maintained anywhere between 62°F (17°C)
and 86°F (30°C). If you want to display the actual room temperature, see To
Operate on Fan Only section.
TO ADJUST FAN SPEEDS:
Press the Fan button to select the Fan Speed in four steps-Auto, Low, Med or
High. Each time the button is pressed, the fan speed mode is changed. On Dry
mode, the fan operates on Low speed automatically.
SLEEP FEATURE:
Press the Sleep button to initiate the sleep mode. In this mode the selected
temperature will increase by 2°F (1°C) 30 minutes after the mode is selected.
The temperature will then increase by another 2°F (1°C) after an additional 30
minutes.
This new temperature will be maintained for 7 hours before it returns to the
originally selected temperature. The Sleep mode program can be canceled at any
time during operation by pressing the Sleep button again.
CHECK FILTER FEATURE:
The Check Filter feature is a reminder to clean the air filter for a more
efficient operation. The light will illuminate after 250 hours of operation.
After cleaning the filter, press the Filter button to reset the Check Filter
function turning the light off.
ECO (ENERGY SAVER) FEATURE:
Press the ECO button to initiate this function. This function is available on
COOL, DRY, AUTO (only AUTO-COOLING and AUTO-FAN) modes. The fan will continue
to run for 3 minutes after the compressor shuts off. The fan then cycles on
for 2 minutes at 10 minute intervals until the room temperature is above the
set temperature, at which time the compressor turns back on and Cooling
resumes.
TO SELECT THE OPERATING MODE:
To choose the operating mode, press the Mode button. Each time you press the
button the unit cycles through the modes, Auto, Cool, Dry, and Fan. The
adjacent indicator light will remain on once the mode is selected.
The unit will automatically initiate the ECO function under Cool, Dry, Auto
(only Auto Cooling and Auto-Fan) modes.
To operate on AUTO mode:
- When you set the air conditioner to AUTO mode, it will automatically select cooling or fan only operation depending on what temperature you have selected and the current room temperature.
- The air conditioner will control room temperature automatically according to temperature you’ve set.
- The fan speed is automatically controlled based on the temperature setting and room temperature and cannot be adjusted.
To operate on Fan Only:
- Use this function when cooling is not desired, such as for room air circulation or to exhaust stale air (On some models, remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer.
- During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode.
- In Fan Only mode, the temperature is not adjusted.
To operate on DRY mode:
- In this mode, the air conditioner will generally function as a dehumidifier. Since the conditioned space is a closed or sealed area, some degree of cooling will occur.
TIMER: AUTO START/STOP FEATURE:
- When the unit is on or off, first press the Timer button. The TIMER ON indicator light illuminates indicating the Auto Start program has initiated.
- When the time of TIMER ON is displayed, press the Timer button again. The TIMER OFF indicator light illuminates. It indicates the Auto Stop program has initiated.
- Press or hold the UP or DOWN button to change the Auto time by 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start.
- The selected time will register in 5 seconds, and the system will automatically revert back to display the previous temperature setting or room temperature when the unit is on. (when the unit is off , there is no display.)
- Turning the unit ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the Auto Start/Stop timed program.
- If setting ON 0.5 and OFF 1 at the same time, the unit will be activated in 0.5 hour, operates for 0.5 hour and then stops.
CONNECT FEATURE:
Press the CONNECT button for 3 seconds to turn off the unit and initiate
Connect mode. To use the Connect feature for the first time, press the connect
button for 3 seconds to turn off the unit and initiate the connect mode.
The display will flash AP every 3 seconds to indicate it is ready to connect
to smart. If the connection is successful within 8 minutes the unit will exit
connect mode automatically and the connect indicator illuminates.
If connection fails within 8 minutes, the unit exits connect mode
automatically.
NOTICE
During the network configuration process, do not try using the remote control
or the controls on the front panel of the air conditioner, as they will be
inoperative. You may use the remote control and front panel buttons again
after the network configuration process is complete (usually 8 10 minutes).
DISPLAYS
DISPLAYS:
Shows the set temperature in “°C” or “°F” and the Auto-timer settings. While
on Fan Only mode, it shows the room temperature.
Error codes:
AS – Room temperature sensor error – Unplug the unit and plug it back in. If
error repeats, call for service.
NOTE: In Fan Only mode, it will display “LO” or “HI.”
ES – Evaporator temperature sensor error – Unplug the unit and plug it back
in. If error repeats, call for service.
NOTICE
If the unit shuts o unexpectedly due to the power outage, it will restart with
the previous function setting automatically when the power resumes.
Additional Information
Now that you understand the operating procedure, here are more features in
your control that you should become familiar with.
- The Cool circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.
- The control can display temperature in Fahrenheit or Celsius. To convert from one to the other, press and hold the UP ( ) or DOWN ( ) Temp/Timer buttons at the same time, for 3 seconds.
FRESH AIR VENT CONTROL (FOR 10000 BTU/H TO 14500 BTU/H)
The Fresh Air Vent allows the air conditioner to:
- Recirculate inside air – Vent Closed (See Fig. A)
- Draw fresh air into the room – Vent Open (See Fig. B)
- Exchange air from the room and draw fresh air into the room – Vent and Exhaust Open (See Fig. C).
AIR DIRECTIONAL LOUVERS
The louvers will allow you to direct the air flow up or down (on some models) and lefts or right throughout the room as needed. Pivot horizontal louvers until the desired up/down direction is obtained. Move the levers from side to side until the desired left/right direction is obtained.
INSTALLATION INSTRUCTIONS
WARNING – Before You Begin
Read these instructions completely and carefully.
- IMPORTANT – Save these instructions.
- IMPORTANT – Observe all governing codes and ordinances.
We recommend that two people install this product.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the Limited
Warranty.
You MUST use all supplied parts and use proper installation procedures as
described in these instructions when installing this air conditioner.
Do not, under any circumstances, cut or remove the third (ground) prong from
the power cord.
Do not change the plug on the power cord of the air conditioner.
Aluminum house wiring may present special problems – consult a qualified
electrician.
When handling the air conditioner, be careful to avoid cuts from sharp metal
edges and aluminum fins on front and rear coils. Please wear cut-resistant
gloves.
NOTICE
Save the carton and these installation instructions for future reference.
The carton is the best way to store the unit when not in use.
Window Requirements
Your air conditioner is designed to install in standard double hung windows
with opening widths of 23” to 36” (584mm to 914mm).
Table 1
H/Model | 8000 BTU/h | 10000~14500 BTU/h |
---|---|---|
14” (356mm) | 15-1/2” (394mm) |
Tools You Will Need
| Phillips Screwdriver
---|---
| Level
Tools You May Use
| Flathead Screwdriver
---|---
| Pencil
| Ruler or tape measure
| Scissors or knife
1. Prepare the Window
Lower sash must open sufficiently to allow a clear vertical opening (see
dimension H in Table 1). Side louvers and the rear of the AC must have clear
air space to allow enough airflow through the condenser for heat removal. The
rear of the unit must be outdoors, not inside a building or garage.
CAUTION
When handling unit, be careful to avoid cuts from sharp metal edges and
aluminum fins on front and rear coils.
2. Prepare the Air Conditioner
Before installing the unit, the top rail must be assembled on the unit.
A: Remove the air conditioner from the carton and place on a flat surface.
B: Remove top rail from the packaging material as shown in Fig. D.
C. Align the hole in the top rail with those in the top of the unit as shown
in Fig. E.
D. Secure the top rail to the unit with the 3/8” Screws as shown in Fig. F.
WARNING
For safety reasons, all four (4) screws MUST be securely fastened.
3. Install Accordion Panels on Air Conditioner
NOTICE
The Top rail and Sliding Panels on each side are offset to provide the proper
pitch to the rear of the unit 5/16” (8mm). This is necessary for proper
condensate management
and drainage. If you are not using the Side Panels for any reason, this pitch
to the rear must be maintained.
Place unit on the floor, a bench or a table. There is a left and right side
accordion panel; be sure to use the proper panel for each side. When
installed, the flange for securing the panel in place to the window sill will
be facing into the room.
A. Hold the side panel in one hand and gently pull back the center to free the
open end. See Fig. 1.
B. Slide the free end “ “ section of the panel directly into the cabinet as
shown in Fig. 2.
Slide the panel down. Be sure to leave enough space to slip the top and bottom
of the frame into the rails on the cabinet.
C. Once the panel has been installed on the side of the cabinet, make sure it
sits securely inside the frame channel by making slight adjustments. Slide the
top and bottom ends of the frame into the top and bottom rails of the cabinet.
Fig. 3.
D. Slide the panel all the way in and repeat on the other side.
NOTICE
If storm window blocks AC, see Fig. 11.
4. Install Air Conditioner
A. While keeping a firm grip on the air conditioner, carefully place the unit
into the window opening so the bottom of the air conditioner frame is against
the window sill (Fig. 5). Carefully close the window behind the top rail of
the unit.
NOTICE
Check that air conditioner is tilted back per dimension H (Fig. 5) (tilted
about 3° to 4° downward to the outside). After proper installation, condensate
should not drain from the overflow drain hole during normal use. Adjust the
slope if otherwise.
B. Extend the side panels out against the window frame (Fig. 6).
5. Secure Air Conditioner
A. Place the frame lock between the frame extensions and the window sill as
shown (Fig. 7A for Wooden windows), (Fig. 7B for Vinyl-Clad windows). Drive
3/4” (19 mm) or 1/2” (12.7 mm) locking screws through the frame lock and into
the sill.
NOTE: To prevent window sill from splitting, drill 1/8” (3 mm) pilot
holes before driving screws.
B1: For wooden windows:
Drive 1/2” (12.7 mm) locking screws through the top rail and into the window
sash (Fig. 8A).
NOTE: To prevent window sill from splitting, drill 1/8” (3mm) pilot holes
before driving screws. Drive 1/2” (12.7mm) locking screws through frame holes
into window sash (Fig. 8B).
B2: For Vinyl-Clad windows:
Drive 1/2” (12.7 mm) locking screws through the top rail and into the window
sash (Fig. 8B).
NOTE: Before driving the screws, drill 5 holes into the window through
the holes of the top rail and side panel frames as shown (Fig. 8B).
C. Secure lower sash in place by attaching the sash lock with the 3/4” (19 mm) or 1/2” (12.7 mm) screw as shown (Fig. 9).
D. Cut Window sash seal foam and insert it in the space between the upper and lower sashes (Fig. 10).
If AC is Blocked by Storm Window
Add wood as shown in Fig. 11, or remove storm window before air conditioner
is installed.
If storm window frame must remain, be sure the drain holes or slots are not
caulked or painted shut. Accumulated rain water or condensation must be
allowed to drain out.
Removing AC From Window
- Turn AC off, and disconnect power cord.
- Remove sash seal from between windows, and unscrew sash lock.
- Remove screws installed through top rail and side panel frames.
- Close (slide) the side panels into the rails.
- Keeping a firm grip on the air conditioner, raise the sash and carefully remove.
- Be careful not to spill any condensate while lifting unit from window. Store parts WITH air conditioner.
CARE AND CLEANING
CAUTION
Clean your air conditioner occasionally to keep it looking new. Be sure to
unplug the unit before cleaning to prevent shock or fire hazards.
Air Filter Cleaning
The air filter should be checked at least once every two weeks to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils and reduce performance.
-
Grasp the filter by the center and pull up and out.
-
Wash the filter using warm water. Rinse filter thoroughly.
-
Gently shake excess water from the filter.
Be sure the filter is thoroughly dry before replacing. -
Instead of washing, you may also vacuum the filter clean rather than washing.
NOTICE
Never use hot water over 104°F (40°C) to clean the air filter. Never attempt
to operate the unit without the air filter.
Cabinet Cleaning
-
Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry.
-
Never use harsh cleansers, wax or polish on the cabinet front.
-
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner. -
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter, remove it
carefully from the window according to the installation instructions. Cover it
with plastic or return it to the
original carton.
TROUBLESHOOTING TIPS
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not the result of defective workmanship or materials in this appliance.
Problem | Solution |
---|
Air conditioner does not start.
button.| Wall plug disconnected. Push plug firmly into wall outlet.
Circuit breaker tripped. Reset circuit breaker.
Check if the light on the plug is on. If it is off, press the RESET
Power is OFF. Turn power ON.
Unit turned off and then on quickly. Turn unit off and wait 3 minutes before
restarting.
Air from unit does not feel cold enough.| Room temperature below 62°F (17°C).
Cooling may not occur until room temperature rises above 62°F (17°C).
Temperature sensor behind the air filter is touching the cold coil. Try to
move it so it does not contact the cold coil.
Reset to a lower temperature.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen
for compressor to restart when set in the COOL mode.
Check for potential obstructions blocking the outdoor intake/ exhaust. Clear
any obstructions.
Air conditioner cooling, but room is too warm- ice forming on cooling coil
behind air filter.| Outdoor temperature below 64°F (18°C). To defrost the
coil, set to FAN ONLY mode.
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To
defrost, set to FAN ONLY mode.
Thermostat set too cold for night-time cooling. To defrost the coil, set to
FAN ONLY mode. Then, set temperature to a higher setting.
Air conditioner cooling, but room is too warm- NO ice forming on cooling coil
behind air filter.| Dirty or restricted air filter. Clean filter. Refer to
Care and Cleaning section. To defrost, set to FAN ONLY mode.
Temperature is set too high, set temperature to a lower setting.
Air directional louvers positioned improperly. Position louvers for better air
distribution.
Front of unit is blocked by drapes, blinds, furniture, etc. – restricts air
distribution. Clear obstruction in front of unit.
Any open doors, windows, or registers may allow cold air to escape. Close any
doors, windows, or registers.
The room may be too warm. Allow additional time to remove “stored heat” from
walls, ceiling, floor and furniture.
Air conditioner turns on and off rapidly.| Dirty air filter- air restricted.
Clean air filter.
Outside temperature extremely hot. Set FAN speed to a higher setting to bring
air past cooling coils more frequently.
Check for potential obstructions blocking the outdoor intake/ exhaust. Clear
any obstructions.
Problem| Solution
---|---
Noise when unit is cooling.| Air movement sound. This is normal. If too loud,
set to a slower FAN setting.
Window vibration – poor installation. Refer to installation instructions or
check with installer.
Water dripping INSIDE when unit is cooling.| Improper installation. Tilt air
conditioner slightly to the outside to allow water drainage.
Refer to installation instructions – check with installer.
Water dripping OUTSIDE when unit is cooling.| Unit removing large quantity of
moisture from humid room. This is normal during excessively humid days.
Remote sensing deactivating prematurely (some models).| Remote control not
located within range. Place remote control within 26.2 feet & 180°, radius of
the front of the unit, and pointed in the general direction of the air
conditioner unit.
Remote control signal obstructed. Remove obstruction.
Room too cold.| Temperature setting too low. Increase temperature setting.
Noise when unit starts.| A “da-da” sound may occur for thirty seconds when the
unit is turned on due to the compressor starting. It is normal.
Unit will not connect to WiFi or App does not work (some models).| For
additional support and troubleshooting tips, visit the “Help” tab within the
MSmart Home app.
REMOTE CONTROL AND APP INSTRUCTIONS
Handling the Remote Control
Location of the remote control
Use the remote controller within a distance of 26.2 ft (8 meters) from the air
conditioner, pointing it towards the receiver. Reception is confirmed by a
beep.
CAUTION
- The air conditioner will not operate if curtains, doors or other materials block the signals from the remote control to the unit.
- Prevent any liquid from spilling onto the remote control. Do not expose the remote control to direct sunlight or heat.
- If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function properly. Use curtains to prevent the sunlight from falling on the receiver.
- If other electrical appliances react to the remote control, either move these appliances or consult your local dealer.
NOTICE
- Button design is based on typical model and may vary slightly from the actual one you purchased.
- All the functions described are accomplished by the unit. If the unit is without a feature, the unit will not respond if the corresponding button on the remote is pressed.
- When there are significant differences between features or operation implied by the remote control illustration and the actual functions described in the USER’S MANUAL, the descriptions in the USER’S MANUAL shall prevail.
Remote Controller Specifications
Rated Voltage | 3.0V (Dry batteries R03/LR03x2) |
---|---|
Environment | 23°F ~ 140°F (5°C ~ 60°C) |
Function Buttons
Remote Screen Indicators
Information are displayed when the remote controller is power up.
Mode display
AUTO
COOL
FAN
DRY
| Displayed when data transmitted.
---|---
| Appears when the remote is enabled and can send a signal to the unit. If you
would like to turn the remote off without affecting the unit, point the remote
away from the unit and press the ON/OFF button. To turn the remote on, point
the remote away from the unit and press the ON/OFF button. The unit will not
receive commands from the remote if this indicator is not illuminated.
ON| Displayed when TIMER ON time is set.
OFF| Displayed when TIMER OFF time is set.
| Shows set temperature or room temperature, or time under TIMER setting.
| Indicated all the current settings are locked.
| Displayed when Comfort Sense feature is activated (some units).
| Displayed when SLEEP feature is activated.
Fan speed indication
HIGH | High speed |
---|---|
MED | Medium speed |
LOW | Low speed |
NO display | Auto fan speed |
NOTICE
All indicators shown in the figure are for the purpose of clear presentation.
But during the actual operation, only the relative function signs are shown on
the display window.
How to Use the Buttons
TIMER OPERATION
Press the TIMER button to initiate the Auto-start and Auto-stop setting
program of the unit.
To set the Auto-start/stop time.
- Press the TIMER button. When the TIMER ON indicator is displayed on the LED window of the air conditioner, it indicates the Auto Start setting program is initiated. When the TIMER OFF indicator is displayed on the LED window of the air conditioner, it indicates the Auto Stop setting program is initiated.
- Press or hold the TEMP UP ( )/DOWN ( ) to change the Auto time. The control will count down the time remaining until start/stop.
- The selected time will register in 5 seconds and the air conditioner will automatically revert back to display the previous temperature setting.
- Turning the unit ON or OFF at any time will cancel the Auto Start/stop function.
NOTICE
To cancel the TIMER setting, push the TIMER button and press or hold the TEMP
UP ( )/DOWN ( ) until 0 hour is displayed on the LCD window of the air
conditioner.
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
AUTO STOP >AUTO START
(On > Stop > Start operation)
This feature is useful when you want to stop the air conditioner after you go
to bed, and start it again in the morning when you wake up or when you return
home.
Example:
To stop the air conditioner 2 hours after setting and start it again 10 hours
after setting.
- Press the TIMER button until the TIMER OFF indicator is displayed on the LED display of the air conditioner.
- Use the TEMP UP ( )/DOWN ( ) button to display “2.0” on the LED display of the air conditioner.
- Press the TIMER button again to display the TIMER OFF on the LED display of the unit.
- Use the TEMP UP ( )/DOWN ( ) button to display “10” on the LED display of the unit.
- Wait for 5 seconds until the previous display appears in LED window.
AUTO START > AUTO STOP
(Off > Start > Stop operation)
This feature is useful when you want to start the air conditioner before you
wake up and stop it after you leave the house.
Example:
To start the air conditioner 5 hours after setting, and stop it 8 hours after
setting.
- Press the TIMER button until the TIMER ON indicator is displayed on the LED display of the air conditioner.
- Use the TEMP UP UP ( )/DOWN ( ) button to display “5.0” on the LED display of the air conditioner.
- Press the TIMER button again to display the TIMER OFF on the LED display of the unit.
- Use the TEMP UP UP ( )/DOWN ( ) button to display “8.0” on the LED display of the unit.
- Wait for 5 seconds until the previous display appears in LED window.
NOTES
- Button design is based on a typical model and may slightly vary from the actual one you purchased.
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
– Changes or modifications not approved by the party responsible for compliance
could void users authority to operate the equipment.
Battery Warning:
Do not mix old and new batteries and Do not mix alkaline, standard (carbon-
zinc) or rechargeable (ni-cad, ni-mh, etc.) batteries
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: Midea brand, RG51G(1)/CEFU1
Responsible Party Canada Contact Information
Midea America (Canada) Corp.
Unit 2 – 215 Shields Court
Markham, ON, Canada L3R 8V2
Telephone number or internet contact information:
Midea.ca
FCC Compliance Statement ( products subject to Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
DECLARATION OF CONFORMITY
We hereby declare that this AC is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
SPECIFICATION OF WIRELESS MODULE
Model: US-SK105 | Dimensions: 41 x 24 x 5 (mm) |
---|---|
Antenna Type: Printed PCB Antenna | Operation Temperature: 0°C ~ 45°C / 32°F ~ |
113°F
Frequency: 2400-2483.5MHz| Operation Humidity: 10% ~ 85%
Maximum Transmitted Power: <20dBm| Power Input: DC 5V/300 mA
PRECAUTIONS
- Supports operating systems: iOS 10+ or Android 5+.
- In the event of a OS update, there may be a delay between the update of the OS and a related software update during which your OS may or may not be supported until a new version is released. Your specific mobile phone or problems in your network may prevent the system from working and Midea will not be responsible for any problems that could be caused by incompatibility or network issues.
- This Smart AC only supports WPA-PSK/WPA2-PSK (recommended) encryption.
- To ensure proper scanning of the QR code, your smart phone must have at least a 5-megapixel camera.
- Due to unstable network connectivity, requests may time out. If this happens, re-run the network configuration.
- Due to unstable network connectivity, commands may time out. If this happens, the smartphone app and the actual product may display conflicting information. The information displayed on the actual product is always the most accurate available. Refresh the app to re-sync.
NOTICE
Midea will not be responsible for any problems that could be caused by
incompatibility or network issues, your wireless router and mobile phone.
SYSTEM OVERVIEW
Devices required to use the Smart AC:
- Smart Phone with compatible iOS or Android system.
- Wireless Router
- Smart Air Conditioner
DOWNLOAD AND INSTALL THE APP
https://mapp.appsmb.com/appstatic/download.html
Download the app & activate product
Scan to download app.
- You can also go to the Google Play or App Store and search for MSmart Home.
NOTICE
All the images in this manual are for reference only, your product and app may
look slightly different. The actual product and app instructions have to be
considered.
CREATE YOUR ACCOUNT
- Make sure your smartphone is connected to your wireless router and your wireless router has a working 2.4 GHz internet connection.
- It is recommended to activate your account immediately to be able to recover your password by email.
- Press Login.
- Select Sign Up.
- Select Sign Up.
- Enter the verification code that was sent to your email address.
NOTICE
- Make sure your smartphone is able to connect to the wireless network which will be used.
- Make sure also that the device is not connecting to other networks in range.
ADDITIONAL APP AND SMART HOME FUNCTIONS
For additional instructions regarding the features of the app and Smart Home
skill capabilities, scan the QR code below.
Declaration of conformity
CONTAINS FCC ID: 2ADQOMDNA21
CONTAINS IC : 12575A-MDNA21
This device complies with Part 15 of the FCC Rules and Industry Canada’s
licence exempt RSSs.
Operation is subject to the following two conditions:
- This device may not cause interference;and
- This device must acceptany interference,including interference that may cause undesired operation of the device.
Only operate the device in accordance with the instructions supplied. Changes
or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8 inches) during normal operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Hereby, we declare that this AC is in compliance with the essential
requirements and other relevant provisions of RE Directive 2014/53/EU. A copy
of the full DoC is attached.
NOTE:
All the illustrations in the manual are for explanation purpose only. Your
unit may be slightly different. The actual shape shall prevail.
WARRANTY
Air Conditioner Limited Warranty
Your product is protected by this Limited Warranty:
Warranty service must be obtained from Midea Consumer Services or an
authorized Midea servicer.
Warranty
- One year full warranty from original purchase date.
Midea, through its authorized servicers will:
- Pay all costs for reparing or replacing parts of this appliance which prove to be defective in materials or workmanship.
Consumer will be responsible for:
- Diagnostics, removal, transportation and reinstallation cost required because of service.
- Costs of service calls that are a result of items listed under NORMAL RESPONSABILITIES OF THE CONSUMER**
Midea replacement parts shall be used and will be warranted only for the
original warranty.
NORMAL RESPONSABILITIES OF THE CONSUMER**
This warranty applies only to products in ordinary household use, and the
consumer is responsible for the items listed below:
- Proper use of the appliance in acordance with instructions provided with the product.
- Routine maintenance and cleaning necessary to keep the good working condition.
- Proper installation by an authorized service professional in accordance with instructions provided with the appliance and in accordance with all local plumbing, electrical and/or gas codes.
- Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loosen connections or defects in house wiring.
- Expenses for making the appliance accessible for servicing.
- Damages to finish after installation.
EXCLUSIONS
This warranty does not cover the following:
- Failure caused by damage to the unit while in your possesion (other than damage caused by defect or malfunction), by its improper installation, or by unreasonable use of the unit, including without limitation, failure to provide reasonable and necessary maintenance or to follow the written installation and Operating Instructions.
- Damages caused by services performed by persons other than those authorized by Midea customer service; or external causes such as abuse, misuse, inadequate power supply or acts of God.
- If the unit is put to commercial, business, rental, or other use or application other than for consumer use, we make no warranties, express or implied, including but not limited to, any implied warranty of merchantability or fitness for use or purpose.
- Products without original serial numbers or products that have serial numbers which have been altered or cannot be readily determined.
NOTICE: Some states do not allow the exclusions or limitation of
incidental or consequential damages. So this limitation or exclusion may not
apply to you.
IF YOU NEED SERVICE
Keep your bill of sale, delivery slip, or some other appropriate payment
Record.
The date on the bill establishes the warranty period, should service be
required.
If service is performed, its your best interest to obtain and keep all
receipts.
This written warranty gives you specific legal rights. You may also have other
rights that vary from state to state. Service under this warranty must be
obtained by following these steps, in order:
- Contact Midea Consumer Services or an authorized Midea services at 1 866 646 4332.
- If there is a question as to where to obtain service, contact our consumer relations Department.
Make yourself at home
Documents / Resources
|
Midea MWMWT080CR1A 8,000 BTU Window Air Conditioner With
Remote
[pdf] Owner's Manual
MWMWT080CR1A 8 000 BTU Window Air Conditioner With Remote, MWMWT080CR1A, 8 000
BTU Window Air Conditioner With Remote, Air Conditioner With Remote, With
Remote
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>