VEVOR ZD200 Dual Monitor Stand for Desk User Manual
- June 17, 2024
- VEVOR
Table of Contents
VEVOR ZD200 Dual Monitor Stand for Desk
Product Information
Specifications
-
Model: ZD200
-
Safe Loading Weight: Total: 52.9 lbs Max;
Single: 26.4 lbs Max -
VESA: 7575mm, 100100mm
-
Product Size: 470493940mm
-
Net Weight: 4.60 kg
Product Usage Instructions
Safety Instructions
WARNING: Read this material before using this product. Failure to do so can result in serious injury.
Assembly Precautions
-
Assemble only according to the provided instructions.
-
Keep the assembly area clean and well-lit.
-
Avoid assembling when tired or under the influence of
substances. -
Ensure proper assembly for product capabilities.
-
Refer to the Assembly Diagram for part information.
Use Precautions
- Do not exceed the rated weight limits.
- Follow specified mounting instructions to prevent damage or injury.
- Confirm the supporting surface can bear the weight.
- Use provided mounting screws and avoid over-tightening.
- Avoid choking hazards by keeping small items away from children.
- Only use the product indoors to prevent potential failures.
Assembly Instructions
Please follow the assembly steps provided in the manual carefully. Ensure all parts are unwrapped and separated in a clean work area before proceeding with assembly.
FAQ
Q: Where can I find technical support or warranty information?
- A: For technical support or warranty inquiries, please visit our website at www.vevor.com/support or contact CustomerService@vevor.com.
Q: What are the weight limits and VESA standards for this monitor desk mount?
- A: The safe loading weight is a total of 52.9 lbs max, with a single monitor capacity of 26.4 lbs max. The VESA standards supported are 7575mm and 100100mm.
- This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual.
- The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
SAFETY INSTRUCTIONS
WARNING: Read this material before using this product. Failure to do so can result in serious injury.
Assembly precautions
- Assemble only according to these instructions. Improper assembly can create hazards.
- Keep the assembly area clean and well-lit.
- Keep bystanders out of the area during assembly.
- Do not assemble when tired or when under the influence of alcohol, drugs, or medication.
- The product capabilities apply to properly and completely assembled products only.
- For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.
Use precautions
- Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
PRODUCT PARAMETER
| Model | ZD200 |
|---|---|
| Safe Loading Weight | Total:52.9 lbs Max; Single:26.4 lbs Max |
| VESA | 7575mm, 100100mm |
| Product Size | 470493940mm |
| Net Weight | 4.60 kg |
PARTS LIST
ASSEMBLY STEP
Method 1 —–1a
Method 2—–1b
The desktop has a hole for item 2 to go through
Connect With monitor
Use a wrench (G) to screw the screws (A/B) into the four holes at the back of
the monitor to avoid damaging the monitor by over-tightening the screws
.
- When the display is inserted into the quick-release head, make sure the knob is vertical.
- After insertion, rotate the knob 90 degrees to the left.
- Case 1: Monitor/Arm fall (after installing your monitor)
- Press the arm to make it keep it in a horizontal position and then use the Allen Key to adjust the screw on the arm.
- Turn counter-clockwise(“+” direction) to increase gas spring tension till can hold the weight of your monitor.
- Note: You may need to turn the screw by many circles to tighten the arm.
- Case 2: Monitor/Arm pops up (after installing your monitor)
- Press the arm to make it keep it in a horizontal position and then use the Allen Key to adjust the screw on the arm.
- Turn clockwise(*- ” direction) to reduce gas spring tension till can stay in the position needed.
- Note: You may need to turn the screw by many circles to tighten the arm.
Adjust Flexibility
- If you feel the pitching angle is too tight or too loose when adjusting the mount, please adjust the Screw
Cable Management
Adjustable Instruction
- Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
- Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
- Imported to the USA: Sanven Technology Ltd.Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
- EC REP SHUNSHUN GmbH Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten,Grmany
- UK REP Pooledas Group Ltd Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
- Technical Support and E-Warranty Certificate www.vevor.com/support
NEED HELP? CONTACT US!
- Have product questions? Need technical support? Please feel free to contact us: CustomerService@vevor.com
Documents / Resources
|
VEVOR ZD200 Dual Monitor Stand for
Desk
[pdf] User Manual
ZD200 Dual Monitor Stand for Desk, ZD200, Dual Monitor Stand for Desk, Monitor
Stand for Desk, Stand for Desk
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>