SUPERATV Polaris Ranger XP 900 Powered Flip Windshield Instruction Manual
- June 4, 2024
- SUPERATV
Table of Contents
SUPERATV Polaris Ranger XP 900 Powered Flip Windshield
WARNING
- Do not discard packaging until product has been successfully installed.
- Unless noted, do not completely tighten hardware when assembling.
- SuperATV does not recommend keeping Windshield installed while transporting on an open air trailer. Remove or secure with straps.
- This item is not returnable if the protective film has been removed.
- Test fit to the cage to confirm fitment before removing film.
Windshield Cleaning
- Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
- Do not use a windshield wiper blade or install a motorized windshield wiper
- Never use razor blades, scrapers, squeegees, brushes, etc.
- Thoroughly rinse Windshield to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean Windshield with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
- To prevent water spots, use a chamois to blot Windshield dry.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty
provided by SuperATV® and is not recommended. SuperATV’s® products could
interfere with other aftermarket accessories. If user has aftermarket products
on machine, contact
SuperATV® to verify that they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine
and may increase maintenance and part wear. Operating any off-road machine
while, or after, consuming alcohol and/or drugs increases risk of bodily harm
or death. No
warranty or representation is made as to this product’s ability to protect
user from severe injury or death. SuperATV® urges operators and occupants to
wear a helmet and
appropriate riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any
product purchased from SuperATV®. The total liability of seller to user for
all damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the
product that gave rise to the claim. SuperATV® will warranty only parts
provided by SuperATV®. Any damage or problems with OEM housings, bearings,
seals, or other manufacturers’ products will not be covered
by SuperATV®. SuperATV® parts and products are not warrantied if item was not
installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary
depending on town, city, county, state, etc. Use of certain products on public
streets, roads, or highways may be in violation law. The Buyer is solely and
exclusively legally and
personally responsible for any violation of the law by the installation or use
of the product. You must abide by all local, state, and federal laws,
including but not limited to vehicle safety, traffic laws, and ordinances. It
is your responsibility to know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to
hold SuperATV® harmless from any damage resulting from failure to adhere to
such specifications, warnings and/ or instructions. The Buyer is also
responsible to obey all
applicable federal, state, and local laws and ordinances when operating
his/her vehicle while using this product, and the Buyer agrees to hold
SuperATV® harmless from any
violation thereof.
PARTS
- A Windshield
- B Top Frame
- C Right Bracket
- D Lower Frame
- E Clamp x 4
- F Right Female Hinge
- G Left Male Hinge
- H Right Male Hinge
- J Left Female Hinge
- K Left Bracket
- L Actuator Bracket 1
- M Actuator Bracket 2
- N Actuator Bracket 4
- P Actuator Bracket 3
- Q Actuator x 2
INSTALLATION
- Install Bulb Seal to Windshield (A) in location shown.
- Install Gasket across front of Frame in location shown.
- Install Lower Frame (D) to Windshield (A) with hardware shown.
- Install Top Frame (B), along with Right and Left Female Hinges (F-J), to Windshield (A) with hardware shown.
- Install Left Bracket (K) to Windshield (A) with hardware shown.
- Repeat for Right Bracket (C) installation.
- Tighten hardware.
- Place assembly on machine.
- Insert Right Male Hinge (H) into Right Female Hinge (F).
- Secure Right Male Hinge (H) to holes located in Frame with hardware shown.
- Repeat for Left side
- Align Windshield to machine and tighten Hinge hardware completely.
- Windshield should open and close smoothly. See “Hinge Alignment” if binding occurs.
Hinge Alignment
Hinges to be in-line with each other. Loosen hardware and adjust as necessary.
- Install Actuator Brackets (L)(N) to Clamps (E) with hardware shown.
- Secure Actuator (Q) with hardware shown.
- Repeat for passenger side.
- Tighten hardware.
- Secure Clamps (E) to Cage.
- Repeat for passenger side.
- Secure Actuators (Q) to Right Bracket (K) and Left Bracket (C) with hardware shown.
- Tighten all hardware.
Before drilling any holes, check behind area to be drilled for any interference.
Switch Mounting
- User may install Switch in location different than shown.
- Verify that Harnesses will reach Switch before mounting.
- Remove stock Knockout or cut a new location.
- Connect wiring and secure Switch.
Before permanently mounting Switch, SuperATV recommends testing after all components have been installed.
- Secure Wires, from Actuators, to Cage; use provided Wire-Ties.
- Reinstall Cup Holder.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>