Niko PM552-20803 Wireless Measuring Module User Manual
- June 17, 2024
- niko
Table of Contents
**Niko PM552-20803 Wireless Measuring Module User Manual
**
Niko Home Control wireless network
Niko Home Control draadloos netwerk
Follow the network setup advice to guarantee the meshing of the devices before
installing the measuring module.
More information on mesh network principles:
guide.niko.eu
Also respect a minimum distance of 2 m between a Niko Home Control RF device
(including the smart hub) and
another RF transmitters (for example a Wi-Fi device) or devices such as
motors, pumps, electronic LED transformers
Wiring
The wireless measuring module can be submetered as follows:
single-phase, three circuits
three-phase, three circuits
three-phase, 3P + N (400 Vac)
three-phase, 3P (3 x 230 Vac
****This product must be secured with a miniature circuit breaker (MCB) of
max. 16 A in the electrical cabinet. The MCB rating is limited by national
installation rules.
Make sure to always connect the blue (N) and red (L1) wire to the same earth-
leakage circuit breaker because the measuring module is powered by these
wires. The cables comply with the Euroclass reaction to fire classification
Eca
Dimensions
Installation
All cable inserts in the electrical cabinet need to be sealed off. The method to close off the cable entries is defined by national installation
Mind the correct mounting direction.
Onboarding
The device can be onboarded via the Niko Home Control programming software.
By default, the device will be in onboarding mode.
Follow the addressing instructions in the Niko Home Control programming
software.
**Niko Home Control programming software
**
Download: www.niko.eu/article/550-99102 (Windows)
www.niko.eu/article/550-99202 (Mac
If an installation contains multiple measuring modules, ensure that only one module is powered during onboarding to avoid errors
Control
LED behaviour
Green LED flashing 3 time| | The wireless measuring module is reset to its
default factory settings
---|---|---
Red LED flashing| | The wireless measuring module is ready to be added to the
Niko Home Control wireless network
Reset
| S tep | Action | LED/led |
|---|---|---|
| 1 |
press 10 s
| x 3| flashing
2| | | flashing
Online guide
Online handleiding
Consult guide.niko.eu for more information about the installation, onboarding and troubleshooting.
Specifications
Measurement range with the current clamps supplied : ……. 0 W – 14490 W /
0.44 A – 63 A
Circuit breaker :………………………………………………………………………maximum MCB rating16 A*
Maximummeasurement range for the total measuring module:…………………… 3 x
14490 W
Wireless communication:.. …………. 2.4 GHz IEEE 802.15.4 compatible with the
mesh network of
………………………………………………the wireless hub (552-00001)and wireless bridge (550-00640)
Maximum RF range: …………………………………. 10 m (mesh networking support for longer
range)
Input voltage: ………………………………………………………………………………………………….230 Vac
Radio frequency power: …………………………………………………………………………………..19.5 dB
Number of current clamps: ………………………………………………………………………….3 (included)
Maximum cable size in clamp: . ………………………………………………………………………..10 mm²
Accuracy: .. ………………..> 100 W: IEC62053-21 class 2 (R), class 2 (L), 10 W
< … < 100 W: 5 %
Connection:… …………………………………………………………….three-phase: 3P+N (400 Vac), 50 Hz
……………………………………………………………………………….. three-phase: 3P (3 x 230 Vac), 50 Hz
……………………………………………………………………..single-phase: three circuits of 230 Vac, 50 Hz
Length of the connector cable at each current clamp: …………………………………………. 90
cm
Dimensions: …………………………………………………………………………….86(L) x 86(W) x 37(H) mm
Ambient temperature: ……………………………………………………………………………………0 – 40°C
Protection degree : ………………………………………………………………………………………………. IP20
The cables comply with the Euroclass reaction to fire classification Eca.
The MCB rating is limited by national installation rules.
ZNot suitable for measuring direct current components
Measuring data for informative purposes only, not valid for invoicing
Warnings regarding installation
The installation of products that will permanently be part of the electrical installation and which include dangerous voltages, should be carried out by a qualified installer and in accordance with the applicable regulations. This user manual must be presented to the user. It should be included in the electrical installation file and it should be passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services
CE marking
This product complies with all of the relevant European guidelines and
regulations. For radio equipment Niko llc declares that the radio equipment in
this manual conforms with the 2014/53/EU directive. The full text of the EU
declaration of conformity is available at www.niko.eu
under the product reference, if applicable
Support & contact
+32 3 778 90 80 support@niko.eu
Niko prepares its manuals with the greatest care and strives to make them as
complete, correct and up to date as possible. Nevertheless, some deficiencies
may subsist. Niko cannot be held responsible for this, other than within the
legal limits. Please inform us of any deficiencies in the manuals by
contacting Niko customer services at support@niko.eu
References
- Confluence Mobile - Niko Guide
- Niko - home automation, switches, socket outlets and detector
- Niko Home Control II programming software for Windows
- Niko Home Control II programming software for Mac
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>