IKEA DISKAD Integrated Dishwasher User Manual

IKEA DISKAD Integrated Dishwasher

Product information

• Fig. 1

Familiarising yourself with your appliance

Appliance

You can find an overview of the parts of your appliance here.

Fig. 2

1| Rating plate| Rating plate with E number and FD number. The data you need for Customer Service.
---|---|---
2| Detergent dispenser| Add detergent to the detergent dispenser.
3| Bottom basket| Bottom basket
4| Dispenser for special salt| Add special salt to the dispenser for special salt.
5| Lower spray arm| The lower spray arm washes the tableware in the bottom basket. If the tableware has not been washed properly, clean the spray arms.
6| Tablet collecting tray| During the wash cycle tablets automatically fall out of the deter- gent dispenser into the tablet collecting tray where they can fully dissolve.
7| Top basket| Top basket
8| Cutlery drawer| Cutlery drawer
9| LED| Interior lighting of the appliance.
10| Cutlery shelf| Cutlery shelf
11| Upper spray arm| The upper spray arm washes the tableware in the top basket. If the tableware has not been washed properly, clean the spray arms.
12| Intake opening| The intake opening is required for the Drying.
13| Blow opening| The blow opening is required for the Drying.
14| Filter system| Filter system
15| Dispenser for rinse aid| Add rinse aid to the dispenser for rinse aid.

Features

You can find an overview of the possible features of your appliance and how to use them here.
These features depend on the model of your appliance.

Adjusting top basket with side levers

To wash large items of tableware in the baskets, adjust the shelf position of the top basket.

• Fig. 3  –  4

Reorganising cutlery drawer

You can fold down the side shelves and front prongs to make more space for longer/wider items of cutlery.

• Fig. 5  –  6

Folding down prongs

If you do not need the folding tines, fold them down.

• **Fig. 7

  ---

****

Before using for the first time

Performing the initial configuration

On initial start-up or after a reset to the factory settings, you will need to make settings.
Requirement: The appliance has been installed and connected.

1. . Add special salt.
2.  Add rinse aid.
3. Switch on the appliance.
4. Setting the water softening system.
5.  Set the amount of rinse aid to be dispensed.
6.  Add detergent.
7. Start the Program  with the highest cleaning temperature without tableware.
   We recommend you clean the appliance without table-ware before using it for the first time to remove any marks from water or other residues.

Tip : You can change these settings and other Basic settings at any time.

Adding special salt

If the special salt refill indicator lights up, add special salt to the dispenser for special salt just before the programme starts.
ATTENTION!

• Detergent may damage the water softening system.
• Only fill the dispenser of the water softening system with special dishwasher salt.
• Special salt can damage the tub due to corrosion.
• To make sure that any special salt that escapes is washed out of the tub, add the special salt to the dispenser for special salt immediately before the programme starts.

Fig. 8  –  13

Adding rinse aid
If the rinse aid refill indicator lights up, top up with rinse aid. Only use rinse aid for domestic dishwashers.

Fig. 14  –  17

****

**

**

Setting water softening system

Set the water hardness on your appliance.
Fig. 18

**

**

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here.

WATER HARDNESS °E| HARDNESS RANGE| MMOL/L| SETTING VALUE
---|---|---|---
0 – 8| Soft| 0 – 1.1| H:00
9 – 10| Soft| 1.2 – 1.4| H:01
11 – 12| Medium| 1.5 – 1.8| H:02
13 – 15| Medium| 1.9 – 2.1| H:03
16 – 20| Medium| 2.2 – 2.9| H:04
21 – 26| Hard| 3.0 – 3.7| H:05
27 – 38| Hard| 3.8 – 5.4| H:06
39 – 62| Hard| 5.5 – 8.9| H:07

Regeneration of the water softening system  overview

In order to ensure fault-free function of the water softening system, the water softening system is regenerated in all programmes before the end of the main rinse cycle.
Here you can find an overview of the maximum additional running time and consumption values during regeneration of the water softening system. You can find the column applicable to your product variant according to its water consumption in the Eco 50° programme.
The consumption values specified are laboratory measurements determined in accordance with the currently applicable standard and using the Eco 50° programme and the factory value of the water hardness is set to 16 – 20°E.
Setting the amount of rinse aid
If there are streaks or water marks on tableware, change the amount of rinse aid.
Note:  A low level adds less rinse aid during the wash cycle, a higher setting adds more rinse aid during the wash cycle.
Fig. 19

**

**

Detergent

Only use detergents that are suitable for dishwashers. Both separate and combined detergents are suitable.
For optimum washing and drying results, use separate detergent, adding special salt and rinse aid separately.
Note: Follow the manufacturer’s instructions for each deter-gent.
If you are using tablets, one is enough. Insert the tablets in a horizontal position.
If you are using powder or liquid detergent, follow the manufacturer’s instructions and quantities for dosage in the de-tergent dispenser.
20 ml – 25 ml detergent is sufficient for normal soiling. If tableware is only lightly soiled, slightly less than the amount of detergent specified is usually sufficient.

Controls

You can use the control panel to configure all functions of your appliance and to obtain information about the operating status.
Fig. 20

**

**

| Starting the programme Terminating the programme
8| Timer programming and setting buttons| Setting timer programming Changing basic settings
9| Door opener| Opening the appliance door
10| Display| The display shows information about the remaining running time or the basic settings. You can change the basic settings via the display and the setting buttons.
11| button| If you press               for approx. 3 seconds, you can open the basic settings.

Programmers

You can find an overview of the programmers that can be selected here.
Start a programme:

Fig. 21

Set the start time for a programme

• Fig. 22

PROGRAMME| 1) PROGRAMME DURATION IN H:MIN

2) ENERGY CONSUMPTION IN KWH

3) WATER CONSUMPTION IN L

| PROGRAMME SEQUENCE| ADDITIONAL FUNCTIONS
---|---|---|---

Intensive 70°

| 1) 2:15 – 2:20

2. 1,250 – 1,300

3. 12 – 15

| Intensive:

●    Pre-rinse

●    Clean 70 °C

●    Intermediate rinse

●    Final rinse 50 °C

●    Dry

| ****

Auto 45-65°

| 1) 1:30 – 2:30

2. 0,800 – 1,300

3. 7 – 18

| Sensor optimized:

●    Optimized by sensors de- pending on the soiling of the washing water.

| ****

Eco 50°

| 1) 3:15

2. 0,849

3. 9,5

| Most economical pro gramme:

●    PreRinse

●    Cleaning 50 °C

●    Intermediate rinse

●    Final rinse 35 °C

●    Drying

| ****

Night Program

| 1) 3:55

2. 0,800

3. 10

| Reduced noise:

●    Pre-rinse

●    Clean 50 °C

●    Intermediate rinse

●    Final rinse 35 °C

●    Dry

| ****

Glass 40°

| 1) 1:30 – 1:40

2. 0,850 – 0,900

3. 11 – 14

| Gentle:

●    Pre-rinse

●    Clean 40 °C

●    Intermediate rinse

●    Final rinse 45 °C

●    Dry

| ****

1 hr Programme

| 1) 1:00

2. 1,400

3. 11

| Time optimized:

●    Clean 65 °C

●    Intermediate rinse

●    Final rinse – °C

●    Dry

| ****

Quick 45°

| 1) 0:29

2. 0,800

3. 10

| Time optimized:

●    Clean 45 °C

●    Intermediate rinse

●    Final rinse 50 °C

| ****

Pre Rinse

| 1) 0:15

2. 0,050

3. 4

| Cold rinse:

●    Pre-rinse

| None

Information for test institutes

Test institutes are provided with information for comparability tests, e.g. according to EN60436.
These are the conditions for conducting the tests, however they are not the results or consumption values.
E-mail enquiries to: dishwasher@test-appliances.com
The product number (E-Nr.) and the production number (FD) are required here. They can be found on the rating plate on the appliance door.

Additional functions

You can find an overview of the additional functions that can be selected here.

Reduce time

| ●    The running time is shortened by 20% to 66% depending on the washing programmed.

●    Energy and water con- assumption are increased.

Half load

| ●    Switch on for small loads.

●    It is recommended that less detergent is added to the detergent dispenser than for a full machine load.

●    The running time is shortened.

●    Energy and water consumption are reduced.

Extra Dry

| ●    For a better drying result the final rinse temperature is increased and the drying phase extended.

●    Especially suitable for drying plastic parts.

●    There is a slight increase in energy consumption and the running time is extended.

Hygiene

| ●    To ensure a higher hygiene status for the appliance and tableware, the temperature is raised and maintained for an extra- long period.

●    Especially suitable for cleaning chopping boards or baby bottles.

●    Continuous use of this function increases the hygiene status.

●    This will increase the running time and energy consumption.

Intensive Zone

| ●    Switch on with mixed loads containing table- ware with different soil- ing levels, e.g. place very soiled pots and pans in the bottom basket and normally soiled tableware in the top basket.

●    The spray pressure in the bottom basket is in- creased and the maximum programmer temperature held longer. This will increase the running time and energy consumption.

Handling problems

If you have a problem with your appliance, refer to the “Troubleshooting” section in the full version of the user manual, which is available on the following pages: www.ikea.com.

Information regarding Open Source Software

Information regarding Open Source Software
This product includes software components that are li-censed by the copyright holders as free software or open source software. The appropriate license texts are printed below.
FreeRTOS
Copyright © 2019 Amazon.com, Inc. or its affiliates. All Rights Reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Soft-ware.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FIT- NESS FOR A PARTICULAR PURPOSE AND NONINFRINGE-MENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Technical specifications

●    Max. 1 MPa (10 bar)

Inlet rate| Min. 10 l/min
Water temperature| Cold water.

Hot water max.: 60 °C

Capacity| 14 place settings

You can find more information about your model online at https://eprel.ec.europa.eu/. This web address is linked to the official EU EPREL product database. Please then follow the instructions on searching for the models. The model identifier is made up of the model name and article number without dots. This information can be found on the label on the right side of the appliance door.
Note: To save energy and water, load the machine with the maximum number of place settings specified.

References

• . Spend less. Smile more.
• Appliances.com
• Hej! Welcome to IKEA Global

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>