DWVO BK205 Portable Basketball Hoop for Outside Owner’s Manual

DWVO BK205 Portable Basketball Hoop for Outside

WARNING
IMPROPER INSTALLATION OR SWINGING ON THE RING MAY CAUSE SERIOUS INJURY OR DEATH

Notice to assemblers

• All the basketball systems, including those used for displays, must be assembled and ballasted according to instructions. Failure to follow instructions could result in serious injury.
• Please read all warnings and cautions before assembly, It is recommended to supervise children as they play with this product. This product is to be assembled by 2 adults only!
• We appreciate your purchasing one of our many fine products. We are assured that you will be very satisfied with your selection.

PART LIST

A

|

Plastic head knob

| 1|

Fix Top Pole(W) On Middle Pole(X)

B

|

Bolt, M8x40MM

|

4

| Connect Rim(L),backboard(K) & Backboard support rod (F)

C

|

Bolt, M8x20MM

| 2| Connect Base(N) & Base brace pole (G)

D1

|

Bolt, M8x65 MM

| 2| Connect Top pole(W),Backboard support rod(F) & Fixed plate(E)

D2

|

Bolt, M8x65 MM

|

3

| Connect Top pole(W),Middle pole (X),Elevating rod(J) & Bottom pole (Y)

D3

|

Bolt, MB x 70 MM

|

1

| Connect Bottom pole(Y) & Base brace pole(G)
E| Fixed plate| 1|
F| Backboard support rod| 1|
G| Base brace pole| 2|
H| Wheel| 2|
I| Wheel Shaft| 1|
J| Elevating rod| 1|
K| Backboard| 1|
L| Rim| 1|
M| Net| 1|
N| Base| 1|
w| Top Pole| 1|
X| Middle Pole| 1|
y| Bottom Pole| 1|

Installation Instructions

Step 1

• Insert the Wheel Shaft (1) into Wheel(H), Base(N), and end of Bottom Pole (Y) as shown.

Attention
The side of the lower pipe welded with nuts must be facing backwards and facing the base.

Step 2

• Fix one end of the Base brace pole (G) on the Bottom Pole (Y) by Bolt (D3) as shown.

Step 3

• Fix the other end of Base brace pole (G) on two sides of Base(N) by 2pcs Bolt (C), as shown.

Step 4

• Connect the Elevating rod(J) & Bottom Pole(Y) as shown, Fix them by 1PC Bolt(D2). Then Connect the Middle Pole(X) & Elevating rod(J). Fix them by 1PC Bolt(D2)

Step 5

• Connect the Rim(L), Backboard(K), and backboard support rod (F), by 4pcs Bolt (B), then connect the Top Pole(W) to the backboard support rod(F) and secure with 2pcs Bolt (D1) and Fixed plate (E).

Step 6

• Insert the Top pole(W) into the Middle pole and fix them by Plasticized height (A) & 1pc Bolt(D2) as shown.
• Adjust the height by changing the bolt (D2) in different holes on the Top pole(W)

Attention

1. The Elevating rod(J) and Bottom pole(Y) can be removed.
2. The height adjustment range is 1.35m ~ 2.6m.

Step 7

• Install Net (M) on Rim (L) as shown.

Step 8

• Fill the Base(S) with water or sand to keep it steady.
• If the product does not need to be moved frequently, we Because when fil freezes below there is ce sids it can damage the base.

Note: however, that the sand can not be poured out after being loaded into the base.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>