Lynx LIJPB Insulated Jacket for LPB Side Burner Instruction Manual

June 17, 2024
LYNX

LIJPB Insulated Jacket for LPB Side Burner

Installation
MANUAL
Lynx LIJPB Insulated Jacket for LPB Side Burner

Insulated Jacket

For Outdoor Products

VIJ5301 LIJ27
VIJ5361 LIJ30
VIJ5421 LIJ36
VIJ5541 LIJ42
VIJSB2 LIJ54
VIJPB LIJSB2
LIJPB

IMPORTANT : Before you build the frame, you must take into consideration the total weight of the liner, grill and any fi nishing materials.
Refer to the cutout dimension table for the proper framing dimensions for the insulation jacket. Determine the entry point for both the gas inlet and electrical connections. Make the 4” square holes for gas and electrical connections (rear or bottom access) based on your requirements.
Note: that the electrical connections are located on the left side and the gas connections are located on the right side.
A Carpenter’s “spirit level” should be used to assure that the framing is level, both front to back and side to side. Note: Never under any circumstance should you install the transformer or run a quick disconnect hose inbetween the grill and the inside of the insulating jacket.
Liner Installation
Position the liner into the frame. No part of the combustible enclosure can protrude above the top surface or in front of the face surface of the liner. Shim the liner if necessary.

Cutout Dimensions

Model A B C D E F
LIJ27 33” (83.8 cm) 5” (12.7 cm) 23 ¾“ (60.3 cm) 4 ½” (11.4 cm) 3” (7.6
cm) 11 5/8” (29.5 cm)
VIJ5301 / LIJ30 36” (91.4 cm) 5” (12.7 cm) 26 ½” (67.3 cm) 4 ½” (11.4 cm)
3” (7.6 cm) 11 5/8” (29.5 cm)
VIJ5361 / LIJ36 42” (106.7 cm) 5” (12.7 cm) 23 ¾” (60.3 cm) 4 ½” (11.4
cm) 3” (7.6 cm) 11 5/8” (29.5 cm)
VIJ5421 / LIJ42 48” (121.9 cm) 5” (12.7 cm) 26 ½” (67.3 cm) 4 ½” (11.4
cm) 3” (7.6 cm) 11 5/8” (29.5 cm)
VIJ5541  / LIJ54 60” (152.4 cm) 5” (12.7 cm) 26 ½” (67.3 cm) 4 ½” (11.4
cm) 3” (7.6 cm) 11 5/8” (29.5 cm)
VIJSB2 / LIJSB2 15 ½” (39.4 cm) 3 ½” (8.9 cm) 26 ½” (67.3 cm) 4 ¾“ (12.1
cm) 3 1/8” (8.0 cm) 11 5/8” (29.5 cm)
VIJPB / LIJPB 26 ¼” (68.0 cm) 5 3/8” (13.7 cm) 23 7/8” (62.7 cm) 4 ¾“
(12.1 cm) 3 1/8” (8.0 cm) 11 5/8” (29.5 cm)

Lynx LIJPB Insulated Jacket for LPB Side Burner -
holes

Grill Installation

Use the proper equipment to support the grill. Place the grill into the liner and engage it over the liner lip across the back and sides. The liner is designed to support the grill without additional fasteners.
If desired any gap remaining between the liner and the combustible enclosure may be filled with a non-combustible sealant or caulk.

WARNING
The regulator to be installed outside the insulating jacket.
It can be positioned anywhere in the gas supply line between the grill and the shutoff valve.
Gas tubing should never be installed within the insulated jacket.

Lynx LIJPB Insulated Jacket for LPB Side Burner -
caulk

After installing grill to the insulated jacket, replace the 2 screws on both side of the grill with the included 1” screws, one screw at a time. This is to straighten out the sides of the insulated jacket and reduce the gap to the cabinet.

Insulated Jacket Dimensions

Lynx LIJPB Insulated Jacket for LPB Side Burner - Insulated Jacket
DimensionsLynx
LIJPB Insulated Jacket for LPB Side Burner - fig1Lynx LIJPB Insulated Jacket for LPB Side Burner -
fig2Lynx LIJPB Insulated Jacket for LPB Side
Burner - fig3Lynx LIJPB Insulated Jacket
for LPB Side Burner - fig4Lynx LIJPB
Insulated Jacket for LPB Side Burner - fig5Lynx LIJPB Insulated Jacket for LPB Side Burner -
fig6

Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
662-455-1200
For product information, call 1-888-(845-4641)
or visit our web site atvikingrange.com
072267-000D EN
(011524)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals