Lynx VIJ5301 Insulated Jacket For Outdoor Products Instruction Manual

Installation
MANUAL
Insulated Jacket
For Outdoor Products

VIJ5301
VIJ5361
VIJ5421
VIJ5541
VIJSB2
VIJPB| LIJ27
LIJ30
LIJ36
LIJ42
LIJ54
LIJSB2
LIJPB
---|---

VIJ5301 Insulated Jacket For Outdoor Products

IMPORTANT: Before you build the frame, you must take into consideration the total weight of the liner, grill and any finishing materials.
Refer to the cutout dimension table for the proper framing dimensions for the insulation jacket. Determine the entry point for both the gas inlet and electrical connections. Make the 4” square holes for gas and electrical connections (rear or bottom access) based on your requirements.
Note: that the electrical connections are located on the left side and the gas connections are located on the right side.
A Carpenter’s “spirit level” should be used to assure that the framing is level, both front to back and side to side.
Note: Never under any circumstance should you install the transformer or run a quick disconnect hose in-between the grill and the inside of the insulating jacket.

Liner Installation

Position the liner into the frame. No part of the combustible enclosure can protrude above the top surface or in front of the face surface of the liner. Shim the liner if necessary.

Grill Installation

Use the proper equipment to support the grill. Place the grill into the liner and engage it over the liner lip across the back and sides. The liner is designed to support the grill without additional fasteners.
If desired any gap remaining between the liner and the combustible enclosure may be filled with a non-combustible sealant or caulk.

Cutout Dimensions

(29.5 cm)
VIJ5301I LIJ30| 36″
(91.4 cm)| 5″
(12.7 cm)| 26 1/2″
(67.3 cm)| 4 1/2″
(11.4 cm)| 3″
(7.6 cm)| 11 5/8″
(29.5 cm)
VIJ5361I LIJ36| 42″
(106.7 cm)| 5″
(12.7 cm)| 23 3/4″
(60.3 cm)| 4 1/2″
(11.4 cm)| 3″
(7.6 cm)| 11 5/8″
(29.5 cm)
VIJ5421 I LIJ42| 48″
(121.9 cm)| 5″
(12.7 cm)| 26 1/2″
(67.3 cm)| 4 1/2
(11.4 cm)| 3″
(7.6 cm)| 11 5/8″
(29.5 cm)
VIJ5541 I LIJ54| 60″
(152.4 cm)| 5″
(12.7 cm)| 26 1/2″
(67.3 cm)| 4 1/2″
(11.4 cm)| 3″
(7.6 cm)| 11 5/8″
(29.5 cm)
VIJSB2 I LIJSB2| 15 1/2″
(39.4 cm)| 3 1/2″
(8.9 cm)| 26 1/2″
(67.3 cm)| 4 3/4″
(12.1 cm)| 3 1/8″
(8.0 cm)| 11 5/8″
(29.5 cm)
VIJPB I LIJPB| 26 1/4”
(68.0 cm)| 5 3/8″
(13.7 cm)| 23 7/8″
(62.7 cm)| 4 3/4″
(12.1 cm)| 3 1/8″
(8.0 cm)| 11 5/8″
(29.5 cm)

WARNING
The regulator to be installed outside the insulating jacket. It can be positioned anywhere in the gas supply line between the grill and the shutoff valve.
Gas tubing should never be installed within the insulated jacket.

Insulated Jacket Dimensions

LIJ27

VIJ5301 / LIJ30 VIJ5361 / LIJ36 VIJ5421 / LIJ42 VIJ5541 / LIJ54 VIJSB2 / LIJSB2 VIJPB / LIJPB Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
662-455-1200
For product information, call 1-888-(845-4641) or visit our web site at vikingrange.com

072267-000C
(021523)

References

• Viking Range, LLC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>