Ustellar UT88125 LED Security Light User Guide
- June 17, 2024
- Ustellar
Table of Contents
Ustellar UT88125 LED Security Light
Thank you for ordering from Ustellar. Set-up is easy and takes only a few minutes by following the instructions.
- AC Powered, NOT Solar Powered, NOT Battery Powered.
- NOT Dimmable. Brightness is NOT adjustable.
Warning
- Please check if the light and the parts are intact before installation.
- Make sure to cut off the power before installation.
- Please do not place this light in corrosive conditions.
- If there is any damage to the cord, please cut off the power and stop using it immediately.
- Please do not retrofit the light within the warranty period.
- To ensure the light works properly, please use the voltage indicated on the packing.
Parameters
Dimension
Components
Installation
Safety Information
- This product must be installed by the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- Turn the power OFF before installing.
- Install the height of the light fixture not lower than 5.5ft, to avoid disturbance from small animals on the ground within detection range.
- The sensor should be installed away from air conditioning, refrigerators, stoves and other sensitive to changes in air temperature, as well as windows and other strong hot air flow places, so as not to cause wrong action.
- When the air temperature is close to a person’s body heat, the detection sensitivity will be reduced.
- For best performance, mount the light about 6.5-8ft above the ground.
- If the light is mounted higher than 8ft, aiming the sensor down will reduce the coverage distance.
- Turn off the power.
- Use a power drill (not included) to drill holes on the chosen surface, and use the wall anchors and mounting screws to fasten the light to the surface.
- Plug into the AC power socket and power on the light.
- Remove the plastic sheet from the bottom of the remote controller to activate the controller.
- Point the IR remote control to the motion sensor for control. It is recommended to keep the distance within 16ft for a better remote control experience.
Remote Controller
Manual Mode
Control the security light constantly ON or OFF.
Sensor Mode
MODE1: PIR mode. When people go through the sensor area, the light will turn
on at 100% brightness. After people leave, the light will turn off.
MODE2: DIM mode. When people go through the sensor area, the light will turn
on at 100% brightness. After people leave, the light will turn to 20%
brightness.
MODE3: D2D mode. The light will turn on at 100% brightness at night, and
automatically turn off in the morning. Motion detection will not work in this
mode.
HOLD TIME: detected. Set the duration of the light to 10s/1min/5min/10min once
motion is
LUX: Set the luminance detection. Set to DAY, the light will trigger during
the day. Set to NIGHT, the light will trigger only at night.
SENS: Set the sensor sensitivity for motion detection. Set to LOW, the
sensitivity is low. Set to HIGH, the sensitivity is high.
Note
- The remote controller has a memory function, which means that it can start at your last choice of mode and settings.
- The security light is controlled by the IR remote controller.
- To make it work perfectly, please point the remote controller to the light and make sure there is no obstacle between the light and the remote controller for better signal response.
- After a period of usage, the remote controller might run out of battery and become insensitive or the control distance may be shortened.
- If the remote controller is not working, please try to replace its battery as per the instructions shown below. If the remote controller still fails to work after replacing the new battery, please contact the seller for help.
- There is an LED indicator in the motion sensor. In Manual Mode, the indicator will turn green. In Sensor Mode, the indicator will turn to red.
- The motion sensor is less sensitive if in a radial movement. as shown below (picture 1).
- The motion sensor is more sensitive if in a lateral movement, as shown below (picture 2).
- The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire shall be replaced.
SUITABLE FOR WET LOCATIONS
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 40°C;
Contact Us
Have some issues? No worries! Please reach us via these channels.
Our customer services team is more than happy to help.
www.ustellar.com
support@ustellar.com
Manufacturer: Shenzhen Ustellar Technology Ltd.
Address: 308A, 3/F, Building A, Youth Entrepreneur Hub, Jianshe East
Road, Qinghua Community, Longhua Street, Longhua District,
Shenzhen, CHINA 518000
Step 1: Scan the QR code
Step 2: Click E-manual PDF file
Step 3: Read the file online or download
Go paper-free, make life easier, and do something good for the environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>