Haws 1119FR Drinking Fountain Instruction Manual
- June 17, 2024
- haws
Table of Contents
INSTALLATION, OPERATION &
MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane
Sparks, NV 89431-6467
775-359-4712 Fax
775-359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
No. 0002076627 (15)
Model 1119FR
Drinking Fountain
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
LIMITED WARRANTY
HAWS warrants that all of its products are guaranteed against defective
material or poor workmanship for a period of one year from the date of
shipment. The foregoing notwithstanding, HAWS warrants certain specific
products or components thereof for an adjusted period. A list of these
excepted p ro ducts and components and a description of their respective
warranty terms may be found here:
www.hawsco.com/warranty. HAWS’ liability
under this warranty shall be discharged by furnishing without charge F.O.B.
HAWS factory any goods, or part thereof, which shall appear to the Company
upon inspection to be of defective material or not of first-class workmanship,
provided that a claim is made in writing to Company within a reasonable period
after receipt of the product. Where claims for defects are made, the defective
part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
shall not be liable for the cost of repairs, alterations or replacements, or
the labor required to implement them, or for any expense connected therewith
made by the owner or owner’s agents, except upon written authority from HAWS .
HAWS shall not be liable for any damages caused by defective materials or
poor workmanship, except for replacements, as provided above. Buyer agrees
that HAWS has made no o ther
warranties either express or implied in addition to those above stated, except
that of title with respect to any of the products or equipment sold hereunder
and that HAWS shall not be liable for general, special , incidental, or
consequential damages claimed to arise under the contract of sale.
Equipment manufactured by HAWS is warranted to function if installation and
maintenance instructions provided are adhered to. The units also must be used
for the purpose for which they were intend ed. Any HAWS emergency equipment is
intended to supplement first-aid treatment. Due to widely varying conditions,
HAWS cannot guarantee that the use of this emergency equipment will prevent
serious injury or the aggravation of existing or prior injuries.
EXCEPT AS EXPRESSLY STATED HEREIN, HAWS HEREBY DISCLAIMS ALL WARRANTIES,
WHETHER EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY MAY NOT BE MODIFIED OR EXTENDED WITHOUT THE
WRITTEN CONSENT OF HAWS. REMEDIES AND REPLACEMENTS STATED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL HAWS BE LIABLE FOR ANY SPECIAL, PUNITIVE,
CONSEQUENTIAL OR INCIDENTAL DAMAGES TO ANY PERSON INCLUDING BUT NOT LIMITED
TO DAMAGES FOR LOSS OF USE OR PROFITS, SUBSTITUTE PRODUCTS OR COSTS, PROPERTY
DAMAGE, OR OTHER MONETARY LOSS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS MODEL PLEASE
CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12″
adjustable wrench, 10″ pipe wrench, 5/64“ hex key wrench, 9/16”, 1/2″, 7/16”
socket wrench or open end wrench.
LOCATION OF UNIT: The Model 1119FR Drinking Fountain is a wheelchair
accessible drinking water facility. The height dimensions that are shown meet
current ADA requirements. When installing this unit, local, state or federal
codes should be adhered to. If height other than shown is required, then
dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2” IPS with 30-90 psi
(2-6 ATM) pressure. Where sediment or mineral content is a problem, an inlet
filter is recommended.
PLUMBING CONNECTIONS: Waste outlet is 1-1/4” NPT (located on 6521FR Valve
box).
MAINTENANCE : Refer to 6521FR operation and maintenance sheet for more
information.
TROUBLESHOOTING
| PROBLEM | REPAIR CHECKLIST |
|---|---|
| 1. Insufficient bubbler flow. | 1a. Check that inlet screwdriver stop valve is |
wide open. Turn counter-clockwise.
b. Verify minimum 30 psi flowing supply pressure.
c. Adjust valve to increase flow. See 6521FR Valve Manual.
General Notes:
Before tightening nut and ferrule assembly, push tubing into fitting until it
bottoms out to ensure correct engagement with O-Ring.
For more information about Haws products, see our website:
www.hawsco.com
PARTS BREAKDOWN
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
| ITEM | DESCRIPTION | PART NO. |
|---|---|---|
| 1 | FREEZE RESISTANT VALVE | 6521FR |
| 2 | BOTTOM PLATE 1105 | PBM1105 |
| 3 | BUBBLER HEAD 5703M | 5703M |
| 4 | PUSH BUTTON ASSEMBLY | 5881PBA |
| 5 | MOUNTING PLATE | 6700. |
| 6 | BOTTOM PLATE 1109 | PBM1109 |
* OPTIONAL
** REQUIRED – SOLD SEPARATELY OR AS PART OF PRODUCT BUNDLES (E.G., 1119FR WITH
TWO 6521FR’S OR 1119FR WITH 1920FR (NOT SHOWN) AND THREE 6521FR’S).
NOTE:
- ENSURE TUBE IS DISCONNECTED FROM “PUSH-IN” TYPE CONNECTOR ON PRESSURE REGULATOR PRIOR TO REMOVAL. APPLY A DROP OF LOCTITE 222MS ON NOZZLE THREADS PRIOR TO REASSEMBLING BACK ONTO BUBBLER HEAD.
REATTACH TUBE TO “PUSH-IN” TYPE CONNECTOR ENSURING IT IS FULLY BOTTOMED OUT.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
E-MAIL:
HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTES:
-
THIS FOUNTAIN REQUIRES THE USE OF MODEL 6521FR FREEZE RESISTANT VALVE ASSEMBLY (SOLD SEPARATELY OR AS PART OF PRODUCT BUNDLES (E.G., 1119FR WITH TWO 6521FR’S OR 1119FR WITH 1920FR (NOT SHOWN) AND THREE 6521FR’S). SEE 6521FR INSTALLATION INSTRUCTIONS FOR CONNECTION DETAILS.
-
VALVE ASSEMBLY MUST BE INSTALLED IN A WARM AREA. PROVISIONS SHOULD BE MADE TO ALLOW ACCESS TO ACCESS PANEL
-
MAXIMUM ADJUSTABLE RANGE IS 15° FROM
PARALLEL TO BACK OF WALL. -
HOLD ROUGH-IN DIMENSIONS ± 1/4″ (6.4mm).
-
WHEN INSTALLING THIS UNIT LOCAL, STATE OR FEDERAL CODES SHOULD BE ADHERED TO. FOR INSTALLATION HEIGHTS OTHER THAN SHOWN, DIMENSIONS MARKED () MUST BE ADJUSTED ACCORDINGLY.
1455 KLEPPE LANE
SPARKS, NEVADA 89431
775-359-4712 FAX
775-359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
© 2022 Haws Corporation – All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
References
- Bottle Fillers Drinking Fountains & Safety Equipment | Haws
- Bottle Fillers Drinking Fountains & Safety Equipment | Haws
- Warranty - Haws Co
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>