Haws 3612F Outdoor Bottle Filler Dual Drinking Fountain Instruction Manual
- June 4, 2024
- haws
Table of Contents
3612F Outdoor Bottle Filler Dual Drinking Fountain
Instruction Manual
INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS
1455 Kleppe Lane
Sparks, NV 89431-6467
775-359-4712
Fax775-359-7424
E-mail:haws@hawsco.com
website:www.hawsco.com
No. 0580001180 (2)
3612F Outdoor Bottle Filler Dual Drinking Fountain
MODELS 3612 & 3612F
Outdoor Bottle Filler/Dual Drinking Fountain
NOTE TO INSTALLER: Please leave this information with the Maintenance
Department.
LIMITED WARRANTY
HAWS warrants that all of its products are guaranteed against defective
material or poor workmanship for a period of one year from the date of
shipment. The foregoing notwithstanding, HAWS warrants certain specific
products or components thereof for an adjusted period. A list of these
excepted products and components and a description of their respective
warranty terms may be found here: www.hawsco.com/warranty. HAWS’ liability
under this warranty shall be discharged by furnishing without charge F.O.B.
HAWS factory any goods, or part thereof, which shall appear to the Company
upon inspection to be of defective material or not of first-class workmanship,
provided that a claim is made in writing to Company within a reasonable period
after receipt of the product. Where claims for defects are made, the defective
part or parts shall be delivered to the Company, prepaid, for inspection. HAWS
shall not be liable for the cost of repairs, alterations or replacements, or
the labor required to implement them, or for any expense connected therewith
made by the owner or owner’s agents, except upon written authority from HAWS.
HAWS shall not be liable for any damages caused by defective materials or poor
workmanship, except for replacements, as provided above. Buyer agrees that
HAWS has made no other warranties either express or implied in addition to
those above stated, except that of title with respect to any of the products
or equipment sold hereunder and that HAWS shall not be liable for general,
special, incidental, or consequential damages claimed to arise under the
contract of sale. Equipment manufactured by HAWS is warranted to function if
installation and maintenance instructions provided are adhered to. The units
also must be used for the purpose for which they were intended. Any HAWS
emergency equipment is intended to supplement first-aid treatment. Due to
widely varying conditions, HAWS cannot guarantee that the use of this
emergency equipment will prevent serious injury or the aggravation of existing
or prior injuries.
EXCEPT AS EXPRESSLY STATED HEREIN, HAWS HEREBY DISCLAIMS ALL WARRANTIES,
WHETHER EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY MAY NOT BE MODIFIED OR EXTENDED WITHOUT THE
WRITTEN CONSENT OF HAWS. REMEDIES AND REPLACEMENTS STATED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL HAWS BE LIABLE FOR ANY SPECIAL, PUNITIVE,
CONSEQUENTIAL OR INCIDENTAL DAMAGES TO ANY PERSON INCLUDING BUT NOT LIMITED TO
DAMAGES FOR LOSS OF USE OR PROFITS, SUBSTITUTE PRODUCTS OR COSTS, PROPERTY
DAMAGE, OR OTHER MONETARY LOSS.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS MODEL,
PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE:
1-888-640-4297
RECOMMENDED TOOLS:
– Measuring Tape
– PVC Pipe Cutter
– Plastic Tubing Cutter
– PVC Solvent Weld Glue
– ¼” Bit-Holding Screwdriver
– Level
– 10” Pipe Wrench
– Adjustable Plier
– 1/8 and 5/32 Tamper Resistant Hex Bits (Supplied)
– 9/16” and 5/8” Box/Open Combination Wrenches, 8” Max Length
– 3/8” Socket Wrench/Rachet, 8” Max Length
– 9/16” Deep Socket
– 15/16” Socket
LOCATION OF UNIT: The Model 3612/3612F (with Filter) Bottle Filler and
Dual Fountain can be installed and assembled to be ADA accessible by first
locating the pedestal base with at least 8 inches of clear unobstructed
hardscape behind the pedestal. Provide a hardscape that is at least 74 inches
wide. When the right pedestal arm is installed in the high orientation, the
height dimensions shown on the model specification sheet meet current Federal
Americans with Disabilities Act (ADA) wheelchair requirements. When the left
pedestal arm is installed in the highest position, the height dimensions shown
on the model specification sheet meet current ADA standing height
requirements. The bottle filler meets ADA requirements for either a front
approach or a side approach. When installing this unit, local, state and
federal (including ADA) codes must be adhered to. If height other than shown
is required, then dimensions must be adjusted accordingly.
ATTENTION: For model 3612F (model with Filter), the Operating Temperature
Range for the 6477 Filter Kit Assembly (Required – supplied separately) is 40°
F – 100° F (4.4° C – 37.8° C).
SUPPLY LINE: Model 3612 – The minimum recommended line size is 1/2“IPS
with 30-90 psi (2-6 ATM) flowing pressure. Where sediment or mineral content
is a problem, an inlet filter is recommended. Model 3612F (with Filter) – The
minimum recommended line size is 1/2“IPS with 40-90 psi (2.76-6 ATM) flowing
pressure.
PLUMBING CONNECTIONS: Model 3612 – The water supply inlet connection is a
3/8“O.D. compression fitting. The waste outlet is 1-1/2” PVC pipe. Model 3612F
– The water supply inlet and outlet connection (for Filter) is a 3/8“O.D.
push-in type fitting. The waste outlet is 1-1/2” PVC pipe. Plumbing
connections will vary depending on how each model is configured during
assembly. Please consult the installation drawings below for supply and waste
fitting arrangements and assembly for your specific model.
MAINTENANCE:
Models 3612 & 3612F Periodically clean the pushbutton valve strainer.
Refer to 5874 Series Valve Operation and Maintenance Manual for more
information. Model 3612F – Filter replacement to occur at 1 year maximum or
3,000 gallons aximum, whichever comes first. Replace filter per Filter
Replacement instructions listed on model 6477 Operation & Maintenance Manual.
INSTALLATION PROCEDURE
GENERAL NOTES:
1. For all compression fitting connections, only connect NSF-61 copper or
plastic 3/8” outside diameter tubing. The following assembly instructions must
be followed to ensure a watertight connection:
a. Cut tubing square and clean. Deburr if necessary.
b. Place compression nut and ferrule over end of the tubing.
c. For plastic tubing (must be ¼” inside diameter), insert supplied tubing
insert into the end of the tubing.
d. Push the tube into the fitting until it bottoms out.
e. Thread nut onto the fitting and tighten snugly with 5/8” wrenches.
Tube Sizes | O.D. Tolerance | Insertion Depth |
---|---|---|
3/8” | ±.005” | 3/4” |
TROUBLESHOOTING
PROBLEM | REPAIR CHECKLIST |
---|---|
1. Insufficient bubbler flow (FromDrinking Fountain) | 1a. For 3612 – Verify |
minimum 30 psi flowing supply pressure. For 3611F – Verify minimum 40 psi
flowing supply pressure
b. Check that the inlet screwdriver stop valve is wide open. Clean inlet
strainer or adjust the valve to increase flow. See 5874 Series Valve Manual.
c. For 3612F (Only) – Check the water filter. Replace at 1 year or 3,000
gallons (max.), whichever comes first.
2. Insufficient bottle filler flow| 2a. For 3612 – Verify minimum 30 psi
flowing supply pressure. For 3612F – Verify minimum 40 psi flowing supply
pressure.
b. The nozzle strainer is clogged. Use a nozzle removal tool to remove
the strainer and replace it. Replacement strainers may be ordered by calling
Customer Service.
C. Check that the inlet screwdriver stop valve is wide open. Clean the
inlet strainer or adjust the valve to increase flow. See 5874 Series Valve
Manual.
D. For 3612F (Only) – Check the water filter. Replace at 1 year or 3,000
gallons (max.), whichever comes first.
*For more information about Haws products, see our website: www.hawsco.com
© 2021 Haws® Corporation – All Rights Reserved
HAWS® and other trademarks used in these materials are the exclusive property
of Haws Corporation.
THIS DOCUMENT IS TRUE AND CORRECT AT THE TIME OF PUBLICATION. CONTINUED
PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE
WITHOUT NOTICE.
REPLACEMENT PARTS DRINKING FOUNTAIN
MODEL 5703M BUBBLER HEAD| MODEL 5874PB PUSHBUTTON| MODEL VRK5874 VALVE REPAIR KIT
REPLACEMENT PARTS BOTTLE FILLER
0410000564 BOTTLE FILLER DRAIN
COVER PLATE| MODEL VRK5874HF VALVE REPAIR KIT,
HIGH FLOW| MODEL VRKNOZ1 QTY 10 AERATORS AND
INSTALL TOOL
REPLACEMENT PARTS FOUNTAIN & BOTTLE FILLER
MODEL PBA7
BUTTON ASSEMBLY| MODEL 6428
FILTER CARTRIDGE
(FOR 36XXF SERIES
MODELS)
0006983506 SPANNER WRENCH| 0510001030 HEX BIT, PINNED, 5/32″ …….0510001029 HEX
BIT, PINNED, 1/8″
OPTIONAL ACCESSORIES
MODEL 3661 HOSE BIB (NOT FREEZE RESISTANT)| MODEL 3660 LOCKABLE HOSE BIB (NOT
FREEZE RESISTANT)
MODEL 3670 DOG BOWL (NOT FREEZE RESISTANT)| MODEL MTG.3600 INSTALLATION AID
THIS DOCUMENT IS TRUE AND CORRECT AT THE TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
AVAILABLE SUB-COMPONENT MODELS
NOTES:
1. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE
ADHERED TO. INSTALL A TRAP IN THE WASTE LINE AND A SCREWDRIVER STOP IN THE
SUPPLY LINE IF REQUIRED.
HAWS MODEL 3612/3612F IS FULLY COMPLIANT WITH THE FEDERAL 2010 AMERICANS WITH
DISABILITIES ACT (ADA) ACCESSIBILITY REQUIREMENTS WHEN INSTALLED AS SHOWN ERE
AND WHEN INSTALLED WITH PROPER CLEARANCES AND ACCESS. LOCATE THE PEDESTAL BASE
WITH AT LEAST 8″ OF CLEAR UNOBSTRUCTED HARDSCAPE BEHIND THE PEDESTAL. IT IS
THE RESPONSIBILITY OF THE INSTALLER TO ADHERE TO LOCAL, STATE,AND FEDERAL
CODES WHEN INSTALLING THIS UNIT. DISTANCE TO SURROUNDING OBJECTS, APPROACH
SURFACES, ETC. SHOULD BE CONSIDERED.
© 2021 Haws Corporation – All Rights Reserved. HAWS® and other trademarks used
in these materials are the exclusive property of Haws Corporation.
INSTALLATION INSTRUCTIONS
STEP 1
MOUNT PEDESTAL TO CONCRETE SLAB IN DESIRED ORIENTATION. SLAB TO BE 30″ MINIMUM
SQUARE AND 6″ MINIMUM THICK (BY OTHERS). PLUMBING CAST IN CONCRETE MUST FIT IN
7″ DIAMETER AREA CENTERED UNDER THE PEDESTAL LOCATION.
STEP 2
REMOVE BOTTOM COVER PLATES FROM ARMS BY REMOVING 3 1/4″ BUTTON HEAD SCREWS.
INSTALL ONE FOUNTAIN ARM ON THE RIGHT SIDE AS SHOWN. USE 1/4″ FLAT HEAD SCREWS
(SUPPLIED) TO INSTALL THE PLATE. USE 3/8″ BOLTS AND NUTS (SUPPLIED) AND TORQUE
TO 18 FT-LBS TO INSTALL THE ARM.
STEP 3
INSTALL REMAINING ARM ON LEFT SIDE AS SHOWN. USE 1/4″ FLAT HEAD SCREWS
(SUPPLIED) TO INSTALL PLATES. USE 3/8″ BOLTS AND NUTS (SUPPLIED) AND TORQUE TO
18 FT-LBS TO INSTALL ARM.
STEP 4
PLACE SQUARE TRIM RING ON BOTTOM OF BOTTLE FILLER AND PLACE BOTTLE FILLER ON
TOP OF PEDESTAL, FACING THE FRONT. USE 3/8″ BOLTS AND NUTS VIA THE FRONT
ACCESS PANEL TO SECURE THE BOTTLE FILLER TO THE PEDESTAL. PLACE TRIM RING AND
INSTALL FOUNTAINS ON ARMS AS SHOWN. CAREFULLY CENTER BOTTLE FILLER, FOUNTAIN,
AND TRIM RINGS, THEN TORQUE BOLTS/NUTS TO 18 FT-LBS
MODEL 3611F (WITH FILTER) SHOWN
STEP 5
INSTALL SUPPLIED DRAIN COMPONENTS AS SHOWN. RED COMPRESSION WASHERS ADAPT FROM
1-1/4″ TO 1-1/2″ AT EACH DRAIN TAIL PIECE. BLACK COMPRESSION WASHERS ARE USED
IN TRAP ADAPTERS AT TEES. USE APPROPRIATE PVC CEMENT TO MAKE SOLVENT CEMENT
CONNECTIONS. TRIM WASTE BEND AND/OR TAIL PIECE LENGTH IF REQUIRED. NOTE THAT
EXTRA PARTS MAY BE INCLUDED TO FACILITATE OTHER CONFIGURATIONS OF THIS
FOUNTAIN.![Haws 3612F Outdoor Bottle Filler Dual Drinking Fountain Instruction
- fig 3](https://manuals.plus/wp-content/uploads/2022/09/Haws-3612F-Outdoor- Bottle-Filler-Dual-Drinking-Fountain-Instruction-fig-3.png)
3612 SUPPLY PLUMBING
STEP 6
COMPLETE WATER SUPPLY PLUMBING AS SHOWN. OPEN SUPPLY VALVE(S) AND TEST.
REPLACE ARM BOTTOM PLATES AND PEDESTAL ACCESS PLATES.
3612F FILTER BRACKET MOUNTING
STEP 7
INSTALL FILTER MOUNTING BRACKET (SUPPLIED WITH MODEL 6477) TO LEFT INSIDE
VERTICAL RAILS USING 2 BUTTON HEAD SCREWS AS INDICATED ABOVE. INSTALL FILTER
HEAD-ON HANGER ANGLE WITH 4 SUPPLIED SELF-TAPPING SCREWS. INSTALL FILTER
HANGER ANGLE BRACKET IN RIGHTMOST HOLES AS SHOWN. SEE MODEL 6477 OPERATION AND
MAINTENANCE MANUAL FOR ADDITIONAL DETAILS.
NOTES ON OPTIONAL CONFIGURATIONS
HAWS 3600/3600F SERIES OUTDOOR FOUNTAINS ARE MODULAR AND CAN BE ASSEMBLED AND
CONFIGURED IN MANY DIFFERENT WAYS. DISPLAYED HERE ARE A FEW EXAMPLES.
CONFIGURATIONS OTHER THAN THAT SHOWN IN THE INSTALLATION INSTRUCTIONS FOR THE
3612/3612F MAY AFFECT COMPLIANCE WITH ADA REGULATIONS. IT IS THE
RESPONSIBILITY OF THE INSTALLER TO UNDERSTAND LOCAL, STATE, AND FEDERAL
REGULATIONS AS APPLICABLE IF INSTALLING THIS FOUNTAIN IN CONFIGURATIONS OTHER
THAN THAT INDICATED ON SHEET 1 (PAGE 6 OF 11).
ADA ARM HEIGHT POSITION OPTIONS
| LEFT SIDE| RIGHT SIDE| ARM HEIGHT (LOWER
EDGE)| BUBBLER NOZZLE HEIGHT
STANDING ADA| YES (STD)| NO| 31-7/8 [809 mm]| 39-3/8 [999 mm]**
WHEELCHAIR ADA| YES| YES (STD)| 27 [687 mm]| 34-5/8 [878 mm]
CHILD ADA| YES| YES| 22-1/4 [566 mm] 29-7/8| [757 mm]
- RIGHT AND LEFT CAN BE REVERSED IF THE PEDESTAL IS ROTATED 180°.
**NOZZLE HEIGHT IS 41-1/2″ WHEN FOUNTAIN IS INSTALLED ON TOP OF THE PEDESTAL.
1455 KLEPPE LANE
SPARKS, NEVADA 89431
775-359-4712 FAX
775-359-7424
E-MAIL: HAWS@HAWSCO.COM
WEBSITE: WWW.HAWSCO.COM
ECN:
5666| REV. ECN:
5719| BY:
DP| MODEL(S)
3612 & 3612F| PART NUMBER
0580001180.D
---|---|---|---|---
DRAWN:
DHP| DATE:
6/11/20| CHK’D.:
BJM
REVISION 2
APPROVED:
FV| DATE:
09/16/21
SCALE: 1:24| I DRAWING TYPE: INSTALLATION| SIZE: A| SHEET 6 OF 6
© 2021 Haws Corporation – All Rights Reserved. HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation.
Documents / Resources
| Haws
3612F Outdoor Bottle Filler Dual Drinking
Fountain
[pdf] Instruction Manual
3612F Outdoor Bottle Filler Dual Drinking Fountain, 3612F, Outdoor Bottle
Filler Dual Drinking Fountain, Dual Drinking Fountain, Drinking Fountain,
Fountain
---|---
References
- Bottle Fillers Drinking Fountains & Safety Equipment | Haws
- Bottle Fillers Drinking Fountains & Safety Equipment | Haws
- Warranty - Haws Co
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>