SUPERATV UForce 1000 XL Aluminum Doors Installation Guide
- June 17, 2024
- SUPERATV
Table of Contents
SUPERATV.COM
INSTALLATION INSTRUCTIONS
Half Doors: for CFMOTO UFORCE 1000XL
UForce 1000 XL Aluminum Doors
- Do not discard packaging until product has been successfully installed.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATV® to verify that
they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
Read instructions and view illustrations before beginning.
Front
| Item | Description |
|---|---|
| A | Right Filler Plate |
| B | Left Filler Plate |
| C | Right Door |
| D | Left Door |
| E | Right Striker Mount |
| F | Left Striker Mount |
| G | Left Frame Mount |
| H | Right Frame Mount |
| J | Right Lower Mount |
| K | Left Lower Mount |
remove components / hardware shown; do not discard
remove components / hardware shown; do not discard
remove components / hardware shown; do not discard
remove components / hardware shown; do not discard
do not tighten hardware completely unless noted (driver side installation shown)
- Install Left Frame Mount (H) with hardware shown.
- Reinstall Cover.
Align Door to machine and tighten all hardware completely.
Rear
| Item | Description |
|---|---|
| L | Left Rear Filler Plate |
| M | Left Rear Door |
| N | Right Rear Door |
| P | Right Rear Filler Plate |
| Q | Left Rear Lower Mount |
| R | Right Rear Lower Mount |
| S | Striker Mount x 2 |
| T | Left Rear Frame Mount |
| U | Right Rear Lower Mount |
Raise Cargo Bed.
Rear Doors
- Install Left Rear Frame Mount (T) with hardware shown.
- Reinstall stock plastic.
- Install Left Rear Lower Mount (Q) to Left Rear Filler Plate (L) with hardware shown.
- Reinstall Cover, over Left Frame Mount (H).
- Install Left Rear Door (M) onto Left Rear Filler Plate (L).
- Install Left Rear Door assembly to Left Rear Frame Mount (T) with hardware shown.
- Secure Left Rear Lower Mount (Q) to Frame with hardware shown; do not tighten.
- Install Striker Mount (S) to Left Frame Mount (H) with hardware shown; do not tighten.
- Install Striker Pin to Striker Mount (S).
- Close Rear Door and engage Latch.
- Align Rear Door to machine and tighen all hardware completely.
- Repeat steps for passenger side installation.
- Lower Bed.
Need help with your installation?
sales@superatv.com
1-855-743-3427
www.superatv.com
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
Thank You For Choosing
SUPERATV.COM
IN-DR-CF-UF1KXL
© 2023 SuperATV.com ®.
All Rights Reserved.
2753 Michigan Road
Madison, Indiana 47250
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>