SUPERATV IN-FDGWS-CA-T Can Am Maverick Sport Flip Down Glass Windshield Installation Guide
- June 17, 2024
- SUPERATV
Table of Contents
SUPERATV IN-FDGWS-CA-T Can-Am Maverick Sport Flip Down Glass Windshield
INSTALLATION INSTRUCTIONS
- SuperATV does not recommend keeping a Windshield installed while transporting on an open-air trailer. Remove or secure with straps.
- Do not discard packaging until the product has been successfully installed.
- Read instructions and view illustrations before beginning.
When assembling, do not tighten the hardware completely.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
the user has aftermarket products on the machine, contact SuperATV® to verify
that they will work together. Although SuperATV® has thousands of satisfied
customers, users should be aware that installing lift kits, long travel, or
suspension kits, tires, etc. will change the ride of a machine and may
increase maintenance and part wear. Operating any off-road machine while, or
after, consuming alcohol and/or drugs increases the risk of bodily harm or
death. No warranty or representation is made as to this product’s ability to
protect users from severe injury or death. SuperATV® urges operators and
occupants to wear a helmet and appropriate riding gear at all times. By
purchasing and installing SuperATV® products, user agrees that should damages
occur, SuperATV® will not be held responsible for loss of time, use, labor
fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party,
will not be held responsible for any direct, indirect, incidental, special, or
consequential damages that result from any product purchased from SuperATV®.
The total liability of the seller to the user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim. SuperATV® will warranty only parts
provided by SuperATV®. Any damage or problems with OEM housings, bearings,
seals, or other manufacturers’ products will not be covered by SuperATV®.
SuperATV® parts and products are not warranted if item was not installed
properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you. The Buyer is responsible to fully understanding the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings, and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
- Install the Center Bracket to Lower with the hardware shown; tighten.
To ease installation, soak 90° Seal in hot water before cutting or installing to increase flexibility.
- Install Left Mount to Lower with the hardware shown.
- Loosen the Clamp and install the Clamp to the Left Mount with the hardware shown.
- Install Lower to a machine.
- Secure Clamps to Cage.
- Install Gasket to Lower.
- Install Upper to machine with hardware shown; tighten.
- Install Straps to the Lower Bracket with the hardware shown; tighten.
- Install Bumpers to the Lower Bracket.
- Install the Lower Bracket to the machine with the stock or hardware shown below.
- The lower Bracket will go underneath the plastic.
- Place the Windshield onto the Lower Bracket and machine.
- Secure the Windshield to the Hinges on the Lower with the hardware shown; tighten.
- Place the Windshield into the closed position, engage the Latches, and align to the machine.
- TIGHTEN ALL HARDWARE.
- Separate components shown from the Wiper and assemble to Windshield; tighten.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>