Canon PIXMA IP90 Inkjet Printer User Manual

1. Turn off a printer. While pressing the Resume/Cancel button, press the Power button.
   The LED lights green to indicate that functions are selectable.

2. While holding the Power button, release the Resume/Cancel button. (Do not release the Power button.)

3. While holding the Power button, press the Resume/Cancel button 3 times, and then release the Power and Resume/Cancel buttons. (Each time the Resume/Cancel button is pressed, the LED alternately lights in either orange or green, starting with orange.)

4. When the LED lights green, press the Resume/Cancel button as many times as you need, to select the preferred function. (See the table below.) Each time the Resume/Cancel button is pressed, the LED alternately lights in either orange or green, starting with orange.

5. After the function (menu) is selected, press the Power button. The LED lights green, and the selected function will be performed. (When the operation completes, the printer returns to the menu selection mode automatically.)

6. Press the Resume/Cancel button the specified number of time(s), then press the Power button.
   Note: When the waste ink counter is reset, print the EEPROM information as shown below, and confirm that the value of the counter is 0 %.

7. Press the Resume/Cancel button the specified number of time(s) according to the destination

Note: After the specific destination is set, print the EEPROM information as shown below, and confirm the model name.

Print sample: 1:iPXXXX 2:V1.02 3:IF(USB=1) 4:D=004.9 PD=000.0 5:ST=2005/09/27-18:30 6:ER(ER0=1000 ER1=5100) 7:LPT=2005/09/028-09:09 8:PC(M=002 R=000 T=001 D=009 C=009) 9:CLT(BK=2005/09/27-18:30 Cl=2005/09/27-18:30) 10:CH=00002 11:CT(BK=040 CL=013) 12:IS(BK=1 C=0 M=1 Y=1) 13:IC(BK=00000 C=00000 M=00000 Y=00000) 14:Power(SON=00009 SOFF=00009) 15:REG=0 16:UR(A(BKoe)=+01 B(Coe)=-01 C(Moe)=+01 D(SCoe)=-01 E(SMoe)=+01 F(BKbi)=+01 G(CLbi)=+01 H(BK-CL)=+01 I(SCLbi)=+01 J(C-SC)=+01 K(M-SM)=+01) 17:WP=0024 18:CDIN(LG=001 PB=000) 19:MSD(015) 20: PAGE(All=00083 PP=00035 HR+MP=00003 PR+SP+SG=00003 GP=00000 PC=00000 ENV=00000) 21:CDPAGE=00003 IRPAGE=00003 BTPAGE=00003 PBPAGE=00000 22:BAT PAGE=00000 23:EDGE=00083 24:L=00000 25:HEAD Temp=30.0 26:Env Temp=30.0 27:FF(3F 3F 3F)

HDEEPROM 1:V0001 2:SN=0000-3D6B 3:LN(00000 00000 000001 000003 00001 00000 00000) 4:ID=00 5:IL=(BK=000 C=+01 M=000 Y=+01 C2=+01 M2=000 Y2=+01)

Printed items:

1. Model name
2. ROM version
3. Connected I/F (USB1)
4. Main waste ink amount, Platen waste ink amount
5. Installation date
6. Operator call/service call error record
7. Last printing time
8. Purging count (manual/deep/timer/dot count/print head installation and removal/ink tank installation and removal)
9. Cleaning time
10. Print head installation and removal (change print head) count
11. Ink tank installation and removal (change ink tanks) count (Bk/CL)
12. Ink status (Bk/C/M/Y)
13. Total ink consumption
14. Power-on count (soft power on/soft power off/hard power on)
15. Print head alignment implementation
16. User print head alignment values (Bkoe/Coe/Moe/SCoe/SMoe/BKbi/CLbi/BK-CL/SCLbi/C-SC/M-SM)
17. Number of times of wiping
18. Number of times of camera port connection and removal (Legacy, PB)
19. Number of the maximum printing intermission in days
20. Number of print pages (total/plain paper/high resolution paper + Matte Photo Paper/Photo Paper Pro + Photo Paper Plus Glossy + Photo Paper Plus Semi-gloss/Glossy Photo Paper/Card/Envelope)
21. Number of Camera Direct Print pages (total), number of IRDA print pages (total), number of Bluetooth print pages (total), and number of Print Beam print pages (total)
22. Number of print pages using battery (total)
23. Number of borderless print pages
24. Number of print page (L/4″ x 6″)
25. Print head temperature
26. Inside temperature
27. Line inspection information

HDEEPROM

1. Version
2. Serial number
3. Lot number
4. Print head ID
5. Ink ejection level (Bk/C/M/Y)

Part 4 TECHNICAL REFERENCE

1. NEW TECHNOLOGY

(1) Highly weather-resistant ink is available (color ink only). BCI-16 Color (highly weather-resistant ink) takes the place of BCI-15 Color.

Note: BCI-16 Color is NOT compatible with BCI-15 Color. Although BCI-16 Color and BCI-15 Color are mechanically and electrically same, the color conversion process of the printer driver is different. Use of BCI-15 Color on the PIXMA iP90 / PIXUS iP90 (or BCI-16 Color on the i80 / PIXUS 80i) is not allowed to avoid undesirable effects on printouts. However, use of BCI-15 Color on the PIXMA iP90 / PIXUS iP90 (or BCI-16 Color on the i80 / PIXUS 80i) does not cause any mechanical damages to the printer.

(2) An ink saving function has been added. In the Maintenance tab of the printer driver, by selecting the following two modes, an ink saving function can be set. This function becomes effective only when the media type is plain paper. In the default setting, the two modes are not set. The setting of two modes does not change until a user command the printer to do so.

Save Black Ink mode:
Black-print duty is reduced to save black ink consumption. In this mode, black printing is faint in some degree.

Use Composite Black mode:
The black color can be available by using color ink even when black ink is used up. In this mode, black becomes slightly greenish. With this mode enabled, the message which makes users recognize that print quality may deteriorate, due to the setting of Use Composite Black mode, is displayed on the screen every time a print job is operated.

(3) The following functions have been added to the Print Beam function. a. AU pictographic symbols (Japan only) b. QR codes (Japan only) c. Reprinting function: By pressing the Resume/Cancel button, printing is preformed again. (Image data only)

(4) Printing on plain paper is supported in PictBridge print mode. When printing on plain paper, borderless printing is not possible. (Even though borderless print is selected, a margin appears.)

(5) In Setup Utility, PictBridge print mode setting is available.

(6) The ink absorber has a 20% longer life. Approx. 20% longer life than that of the i80 / PIXUS 80i with the modification to the purging operation sequence, although the ink absorber is the same as one in the i70 / PIXUS 50i and i80 / PIXUS 80i.

(7) The wait time of the print head before capping is reduced. The period of time before the print head starts to move to the capping position from the home position becomes 11 seconds. In conventional models, it was 55 seconds.

Reason:
To prevent removal of the power cord while the print head is at home position (meaning,
the print head is not capped). The users may feel uncomfortable with an unforeseen frequent movements of the print head (the print head scan sequence*1 before capping). Thus, possible claims are expected.

*1: An action which the print head makes two round trips, from the right to the left, to eject ink mist: This function was newly introduced with the i80 / PIXUS 80i. Available when; Cleaning, Replacement of the print head and ink tanks, and Turning off the power.

2. CLEANING MODE AND AMOUNT OF INK PURGED

Print head cleaning is performed before a start of printing, except in the following cases:
– Cleaning on arrival:
Performed when the print head cover is closed.
– Cleaning by dot count:
Performed after ejecting paper.
– Manual cleaning / deep cleaning: Performed manually.

1: The appropriate interval between the last cleaning and the next is separately maintained for Black and Color with the timer. For this reason, the cleaning mode may differ in Black and Color.
2: When 24 to 504 hours have elapsed since the previous Black cleaning, timer cleaning – 0 is performed. However, this cleaning is conducted only 5 times after printer installation, and no further timer cleaning – 0 (Black) will be performed.

3. PRINT MODE

Default setting
Selectable in the printer driver Main tab.
Selectable after clicking Custom in the Main tab

(1) Standard color printing

1: When “Use Composite Black” mode or “Save Black Ink” mode is selected, 2-pass bidirectional printing is automatically done, and only YMC inks are used.
2 : When the printer driver Print Options is set to “Change the print data size to match the port”, an ink drop size becomes 2 pl when printing with a USB cable, and it is 2 pl/5 pl when printing via wireless connection.

(2) Standard grayscale printing

(3) Borderless printing

(4) Duplex printing

(5) Camera Direct printing (PictBridge)

(6) Print Beam printing

4. FAQ (Specific Problems and Solutions)

• Occurrence level:
  A: The symptom is likely to occur frequently.
  B: The symptom may occur under certain conditions, but likeliness is assumed very low in practical usage.
  C: The symptom is unlikely to be recognized by the user, and no practical issues are assumed.

• Occurrence level:
  A: The symptom is likely to occur frequently.
  B: The symptom may occur under certain conditions, but likeliness is assumed very low in practical usage.
  C: The symptom is unlikely to be recognized by the user, and no practical issues are assumed.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>