Canon TC-80N3 Timer Remote Controller Instruction Manual
- June 17, 2024
- Canon
Table of Contents
Canon TC-80N3 Timer Remote Controller
Thank you for purchasing a Canon product.
Timer Remote Controller TC-80N3 is a remote switch with the following timer control and exposure count control functions. It is very useful for time-lapse photography of blooming flowers, astrophotography, etc.
- Self-timer
- Interval timer
- Long exposure timer
- Exposure count control
- Remote switch function
Connectable to the camera’s quick-lock remote control socket.
The time is settable in 1-sec. units from 1 sec. to 99 hours, 59 minutes, and
59 sec. The set time period can be used for any timer function.
The remote switch function can be used without battery power.
Extension Cord ET-1000N3 (sold separately) can extend the TC-80N3’s distance
to the camera by 10 meters.
Symbols used in this Instructions booklet
- ⚠: Warning for preventing camera and TC-80N3 malfunction.
- ?: Supplementary notes for using the TC-80N3 with the camera.
- ?: Helpful tip for using the TC-80N3 and taking pictures.
Keep this Instructions booklet handy for future reference.
All the instructions in this booklet assume that the TC-80N3 and any other equipment are already turned on. Before proceeding, make sure the TC-80N3 and other equipment are on.
About the LCD Panel
The display panel uses a liquid crystal display. With time, the display will become lighter and harder to read. In such a case, take the product to your nearest Canon Service Center to replace the display panel (at cost). At low temperatures, the display response may become slower. And at 60°C/140°F and higher temperatures, the display may blacken. In either case, the display will return to normal at room temperature.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Specifications
Type| Remote switch with built-in timer control functions and exposure count
control.
---|---
Compatible Cameras| Cameras equipped with a dedicated quick-lock remote
control socket
Control Functions|
- Self-timer
- Interval timer
- Long exposure timer
- Exposure count
Timer Start/Stop| With START STOP button
In-Operation Indicator| Indicated by the mode’s icon displayed or blinking on
the display panel and by the countdown of the remaining time or exposures.
Hold Function| HOLD appears when the ⏺ button is pressed for 3 sec. This
disables all other buttons and dial. The Hold function is canceled by pressing
the ⏺ button for 3 sec. again.
Display Panel Illumination| Pressing the ⏺ button illuminates the display
panel for 6 sec.
Release Button| Provided for halfway and complete pressing. Release lock
provided. Can be used to release the shutter even during self-timer and
interval timer operations.
Camera Connection| Quick-lock remote control socket
Cord Length| 80 cm
Power Source| One lithium CR2032 (3 V) button battery
Battery Life| Approx. 3 years. Exhausted battery indicated by a blinking
battery-low icon on the display panel.
Dimensions| 40 (W) x 20 (H) x 143 (D) mm
Weight| 85g / 3oz (including battery)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry Canada.
The CE Mark is a Directive conformity mark of the European Community (EC)
All data are based on Canon’s Standard Test Method.
Subject to change without notice.
FAQs
How do I connect the TC-80N3 to my camera?
Insert the TC-80N3’s plug into the camera’s quick-lock remote control socket.Can the TC-80N3 be used without battery power?
Yes, the remote switch function can be used without battery power.What is the battery life of the TC-80N3?
Approximately 3 years.What should I do if the LCD panel becomes difficult to read?
If the display becomes lighter and harder to read, take the product to your nearest Canon Service Center for a display panel replacement. At low and high temperatures, the display may become slower or blacken, but it will return to normal at room temperature.Does the TC-80N3 have a Hold function?
Yes, the HOLD function disables all buttons and dials to prevent inadvertent changes.Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>