DIGITAL WATCHDOG DWC-MF5Wi4TWDMP IP Cameras User Guide
- June 17, 2024
- DIGITAL WATCHDOG
Table of Contents
DIGITAL WATCHDOG DWC-MF5Wi4TWDMP IP Cameras
Product Information
Specifications
- Model: 5MP DWC-MF5Wi4TWDMP, 2.1MP/1080p DWC-MF2Wi4TWDMP
- Power Requirements:
- DWC-MF5Wi4TWDMP: DC 12V, PoE IEEE 802.3af Class 3 (Adapter not included)
- DWC-MF2Wi4TWDMP: DC 12V, PoE IEEE 802.3af Class 2 (Adapter not included)
- Power Consumption:
- DWC-MF5Wi4TWDMP: DC12V: max 5.9W, PoE: max 7.2W
- DWC-MF2Wi4TWDMP: DC12V: max 4.0W, PoE: max 5.5W
Product Usage Instructions
Mounting Instructions
- The mounting surface must withstand five times the camera weight.
- Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a short or fire.
- CAUTION: These servicing instructions are for use by qualified personnel only.
- Remove the protective film between the dome and the camera module.
- Remove the Poron Ring before placing the dome back on the camera. When attaching the dome back, align the line on the dome with the one on the base of the camera.
- Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.
- Pass the wires through the mount bracket and make all necessary connections.
- Attach the main body to the mount bracket by tightening the lock screw.
- For soft installation surfaces, use the included metal mount plate. Fix the mount plate on the mounting surface using the included screws. Then, press the bottom case onto the mount plate.The three bezels on the case will align and snap lock onto the plate.
Waterproof Wiring Instructions
- To use the camera’s waterproof wiring:
- Install the LAN cable into a waterproof cap.
- b will be assembled to a with a 1/4 turn.
- Thread c tightly to b.
- NOTE: To ensure moisture seal, make sure the o-ring is in place between a and b. In extreme environments, use of an outdoor rated sealer is recommended.
- NOTE: When using the waterproof cap, crimp the RJ45 connector after passing the cable through the waterproof cap.
Camera Adjustment
Once the installation is complete, adjust the camera’s tilt, panning, and
rotation as needed. The cameras’ max angles are:
- Tilt: [TILT ANGLE]
- Panning: [PANNING ANGLE]
- Rotation: [ROTATION ANGLE]
Resetting the Camera
To reset the camera, use the tip of a paper clip or a pencil and press the
reset button. Pressing the button for five (5) seconds will initiate a camera-
wide reset of all the settings, including network settings.
FAQ
Q: Where can I download support materials and tools for my product?
A: You can download all your support materials and tools from the Digital
Watchdog website at http://www.digital-watchdog.com/resources. Search your
product by entering the part number in the “Search by
Product” search bar. All supported materials, including manuals and quick
start guides (QSGs), will appear in the results.
Q: Is it recommended to read the entire instruction manual?
A: Yes, it is recommended to read the entire instruction manual for
complete and proper camera usage.
WHAT’S IN THE BOX
NOTE: Download all your support materials and tools in one place
- Go to: http://www.digital-watchdog.com/resources
- Search your product by entering the part number in the ‘Search by Product’ search bar. Results for applicable part numbers will populate automatically based on the part number you enter.
- Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference page for the initial setup. It is recommended that the user read the entire instruction manual for complete and proper camera usage.
INSTRUCTION
STEP 1 – PREPARING TO MOUNT THE CAMERAReset
- The mounting surface must withstand five times the camera weight.
- Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a short or fire.
- CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
- This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.49A (DWC-MF5Wi4TWDMP) and 0.33A (DWC-MF2Wi4TWDMP) min.
- The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1 or PS2 as defined in UL62368-1.
- Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.
- For the installation process, remove the dome cover from the camera module by loosening the three (3) screws on the dome. Use the wrench provided with the camera.
- Install the moisture packet in the base of the camera’s lens.
- Remove the moisture absorber from the packaging.
- Cut the card and folder along the dotted line.
- Place the moisture absorber around the camera’s lens module.
- Remove the protective film between the dome and the camera module.
- Remove the Poron Ring before placing the dome back on the camera. When attaching the dome back, align the line on the dome with the one on base of the camera.
- Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.
STEP 2 – POWERING THE CAMERA
Pass the wires through the mount bracket and make all necessary connections.
- NETWORK CONNECTIONS – If you are using a PoE Switch, connect the camera using an Ethernet cable for both data and power.
- NETWORK CONNECTIONS – If you are using a non-PoE switch, connect the camera to the switch using an Ethernet cable for data transmission and use a power adapter to power the camera.
| Part number | Power Requirements | Power Consumption |
|---|---|---|
| DWC-MF5Wi4TWDMP | DC 12V, PoE IEEE 802.3af |
Class 3
(Adapter not included).
| DC12V: max 5.9W
PoE: max 7.2W
DWC-MF2Wi4TWDMP| DC 12V, PoE IEEE 802.3af
Class 2
(Adapter not included).
| DC12V: max 4.0W
PoE: max 5.5W
STEP 3 – INSTALLING THE CAMERA
-
Attach the main body to the mount bracket by tightening the lock screw.
-
For soft installation surfaces, use the included metal mount plate. Fix the mount plate on the mounting surface using the included screws. Then, press the bottom case onto the mount plate. The three bezels on the case will align and snap lock onto the plate.
-
To use the camera’s waterproof wiring:
- a. Install the LAN cable into a.
- b. b will be assembled to a with a 1/4 turn.
- c. Thread c tightly to b.
NOTE: To ensure moisture seal, make sure the o-ring is in place between a and b. In extreme environments use of an outdoor rated sealer is recommended.
NOTE: When using the waterproof cap, crimp the RJ45 connector after passing the cable through the waterproof cap.
-
Once the installation is complete, adjust the camera’s tilt, panning and rotation as needed. The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 70°
Rotation: 0° ~ 360° -
Assemble the dome cover over the camera body and detach the protecting film from the dome bubble.
Resetting the camera:
To reset the camera, use the tip of a paper clip or a pencil and press the
reset button. Pressing the button for five (5) seconds will initiate a camera-
wide reset of all the settings, including network settings.
Installation using Mount Bolt and Screws:
- Using the mounting template, mark and drill the holes on the mounting surface.
- Secure the two long mounting screws to the camera’s base.
- Pass the wires through the mount bracket and make all necessary connections.
- Mount the camera to the mounting surface by using the 2 mounting nuts. Rotate the locking discs over the screws until the camera is held tightly from the mounting surface.
NOTE: Please refer to DMP guide for additional information on integration and camera control.
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Tel: 866-446-3595 /
813-888-9555
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>