JBC ADS T210 Heavy Duty Handles Instruction Manual

: June 13, 2024
: JBC

Table of Contents

INSTRUCTION MANUAL

www.jbctools.com

INSTRUCTION MANUAL

ADS / HDS / DNS

Stands for Handles

This manual corresponds to the following references:

AD-SF (for T210 & T245 Handles)
HD-SF (for T470 Heavy Duty Handles)
DN-SF (for T210N/T245N/T470N Nitrogen Handles)

Packing List

Includes one stand according to purchased reference:

ADS for T210 & T245
Handles ……………………. 1 unit

HDS for T470 Heavy Duty
Handles …………………….. 1 unit

DNS for T210N/T245N/T470N
Nitrogen Handles …………. 1 unit

Sponge for Stands 48 x 26.5 mm …………….. 1 unit
Ref. S7034

Stand Cable 1m ………… 1 unit
Ref. 0024227

Brass Wool ……………….. 1 unit
Ref. CL6210

Manual ……………………….. 1 unit
Ref. 0027177

Features and Connections (ADS)

Cartridge Holder
Cartridge Exchanger
H5450 Tool Holder
CL6210 Brass Wool (inside)
S7034 Sponge
CL7889 Wiper
CC1001 Cable Collector
Control Unit Connector (DI, DDE or DME)
Tool Connector

Assembly

A: Adjustable Cable Collector (CC1001)
B: Adjustable Tool Holder (H5450)
C: Wiper (CL7889)

Insert the cable into the cable collector clip. Do not leave the cable longer than necessary to reach the work area freely.
The cable collector is flexible. It accompanies and adapts to the movements during the soldering process.
Adjust the tool holder angle to suit the work position.
The wiper offers different ways to clean the cartridge tips. If desired use the included sponge.

Cartridge Exchanger

Save time and change cartridges safely without switching the station off. Be careful, the cartridges may be hot when placing them in the storage rack.

Stand ADS (for T210 & T245 Handles)

1. Removing

Place the cartridge in the exchanger and pull the handle to remove it.

2. Inserting

Place the handle on top of the new cartridge and press the handle down.

3. Fixing for ADS and DNS

a: Holes
Depending on the shape of the tip, use one of the holes for fixing the cartridge.

Note: It is essential to insert the cartridge up to the mark for a proper connection.

A: Mark
Stand HDS (for T470 Heavy Duty Handles)

1. Removing

A: Handle Screw
Loosen the handle screw. Place the tool with the cartridge in the exchanger and pull the handle to remove it.

2. Inserting

Place the handle on top of the new cartridge and press the handle down until the cartridge is fully seated.

3. Fixing

A: Mark
B: Handle Screw

Tighten the handle screw.
Note: Prior to tightening the handle screw, make sure that the mark on the cartrige is aligned with the handle (see picture) to ensure a proper cartridge connection.

Nozzle Exchange

Stand DNS (for T210N/T245N/T470N Nitrogen Handles)

The cartridge exchanger for DNS stand features both, one slot for cartridge exchange and one for nozzle exchange. The nozzle exchange works as well as the cartridge exchange.

Use the fixing holes as described for the ADS on page 5.

Cartridge Exchanging Slot
Fixing Holes
Nozzle Exchanging Slot

Wiper

The integrated wiper offers different ways to clean the cartridge tips.

Tapping

Tap gently to remove excess solder.

Wiping

Use the slots to remove the remaining particles.

Sponge

The softest cleaning method. Keep the sponge damp with distilled water when working to avoid tip wear.

Wiper and Brass Wool Replacement

The wiper and brass wool can be easily removed for cleaning or replacement when they are worn.

Lift the wiper at its front edge.

Remove the wiper by pulling it out.

Replace the brass wool with a new one when it is worn out. Place the wiper back or replace them if desired.

Accessories

A1286
Extension Lead for Stands (Length: 1.5 m)
Stand Cable

Compatibility – Stand/Tool/Control Unit

Stands

|

ADS
for T210 & T245 Handles

| HDS
for T470 Heavy Duty Handles|

DNS
for T210/T245/T470 Nitrogen Handles

---|---|---|---

Control Units

Handles

|

DI, DDE, DME

| HDE|

DI, DDE, DME

T210
Presicion Handle| •| |
T210P
Blue Grip Precision Handle| •| |
T210N
Nitrogen Precision Purpose Handle| | | •
T245
General Purpose Handle| •| |
T245G
General Purpose Handle with Reinforced Cable| •| |
T245P
Blue Grip General Purpose Handle| •| |
T245N
Nitrogen General Purpose Handle| | | •
T470
Heavy Duty Handle – 1.5m (4.9ft) cable.| | •|
T470S
Heavy Duty Handle – 3m (9.8ft) cable| | •|
T470F
Thermal Insulator Grip Heavy Duty Handle – 1.5m (4.9ft) cable| | •|
T470M
Thermal Insulator Grip Heavy Duty Handle – 3m (9.8ft) cable| | •|
T470Z
Tri-Lobed Grip Heavy Duty Handle – 1.5m (4.9ft) cable| | •|
T470N
Nitrogen Heavy Duty Handle – 1.5m (4.9ft) cable| | | •

Maintenance

Before carrying out maintenance or storage, always unplug the stand from the station and the tool.
– Use a damp cloth to clean the stand. Alcohol can be used only when cleaning metal parts.
– Check periodically that the metal parts of the tool/stand are clean so that the station can check the tool’s status.
– Periodically check all cables and tube connections.
– Replace any defective or damaged parts. Use original JBC spare parts only.
– Repairs should only be performed by a JBC authorized technical service.

Clean periodically

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

– Do not use the stands for any purpose other than soldering or rework.

– The power cord must be plugged into approved bases. Be sure that it is properly grounded before
use. When unplugging it, hold the plug, not the wire.

– The tool should be placed in the stand when is not in use in order to activate the sleep mode. The soldering tip, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position.

– Avoid the contact of flux with skin or eyes to prevent irritation.

– Be careful with the fumes produced when soldering.

– Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.

– Utmost care must be taken with liquid tin waste which can cause burns.

– This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance.

– Maintenance must not be carried out by children unless supervised.

Specifications

ADS
Stand for T210 & T245 Handles
Ref.: AD-SF

– Includes Sleep Mode
– Total Net Weight 1440 g / 3.17 lb
– Package Dimensions / Weight: 342 x 155 x 120 mm / 2002 g
(L x W x H) 13.46 x 6.10 x 4.72 in / 4.41 lb

HDS
Stand for T470 Heavy Duty Handles
Ref.: HD-SF

– Includes Sleep Mode
– Total Net Weight 1514 g / 3.34 lb
– Package Dimensions / Weight: 342 x 155 x 120 mm / 2076 g
(L x W x H) 13.46 x 6.10 x 4.72 in / 4.58 lb

DNS
Stand for T210N / T245N / T470N Nitrogen Handles
Ref.: DN-SF

– Includes Sleep Mode
– Total Net Weight 1510 g / 3.33 lb
– Package Dimensions / Weight: 342 x 155 x 120 mm / 2072 g
(L x W x H) 13.46 x 6.10 x 4.72 in / 4.57 lb

Complies with CE standards.
ESD safe.

Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here:https://www.jbctools.com/productregistration/ within 30 days of purchase.

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

www.jbctools.com

0027177-050623