DIGITAL WATCHDOG DWC-GPLT-W Converter Plate For Electronic Gang Box User Guide

Quick Start Guide
Converter plate for
electronic gang box
DWC-GPLT-W

DWC-GPLT-W Converter Plate For Electronic Gang Box

WHAT’S IN THE BOX

Option A Installation Screws| | 4
---|---|---
Option B Installation Screws| | 2
Camera Mounting Screws| | 3 sets

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the ‘Search by Product’ search bar. Results for applicable part numbers will populate automatically based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs) will appear in the results.

http://bit.ly/resources_qr

NSTALLAT I ON

1. Connect the converter plate to an electric gang box.
   Use the 4 screws (A) included with the converter plate when using a 2-gang handy electrical box or switch box.
   Use the 2 screws (B) included with the converter plate when using a 1-gang handy electrical box.

2. Pass wires through and make the connections.
   Use the CABLE-OUT spaces in the converter plate.

3. Follow the table below to connect the camera to the appropriate mounting points and which screws set to use.
   Mounting  holes| Compatible cameras| Screw size
   ---|---|---
   Mounting point 1| DWC-V4 models 120mm screws| 20mm screws
   DWC-MV4 models 120mm screw| 20mm screw
   DWC-V6 models 20mm screw| 20mm screw
   Mounting point 2, 2#| DWC-MF and DWC-MPF models 120mm screw| 20mm screw
   DWC-MV8 and DWC-MPVB models| 23mm screw
   DWC-MVC and DWC-MPVC models| 20mm screw
   DWC-MVD and DWC-MPVD models| 35mm screws
   DWC-PVF and DWC-PPVF models| 20mm screw
   Mounting point 4| DWC-MV7 and DWC-MPV7 models| 20mm screw
   DWC-V7 models| 20mm screw
   DWC-MVA and DWC-MPVA models| 20mm screw
   DWC-VA models| 20mm screw
   DWC-D4 models| 20mm screw
   DWC-MF and DWC-MPF models OLD HARDWARE| 20mm screw + rubber gasket I
   DWC-MV8 and DWC-MPVB models OLD HARDWARE| 20mm screw + rubber gasket
   DWC-PVF and DWC-PPVF models OLD HARDWARE| 20mm screw + rubber casket
   Mounting Point 5| DWC-D3 models| 20mm screw
   DWC-MD7 models| 20mm screw
   Mounting point 6| DWC-MD4 models| 20mm screw

4. Mount the camera to the upper side of the converter plate.

• NOTE: How to tell what MF, V8 or PVF hardware you have:
  If the camera’s mounting holes are located on the outer edge of the camera’s base, use mounting points labeled as “2, #2” WITHOUT the included rubber gaskets.
  If the camera’s mounting holes are located on the inner edge of the camera’s base, use mounting points labeled as “4” WITH the included rubber gaskets.

Rev:06/23
Copyright © Digital Watchdog.
All rights reserved.
Specifications and pricing are
subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>