Dasqua IP65 Digital Outside Micrometer Instruction Manual

Dasqua IP65 Digital Outside Micrometer

IP65 WATERPROOF DIGITAL OUTSIDE MICROMETER

Please read through this owners manual carefully before using your new tool. Use your tool properly and only for its intended use.

STRUCTURE

1. Anvil
2. Spindle
3. Locking screw
4. Thimble
5. Rachet
6. Data interface
7. LCD screen
8. Frame shield
9. Frame

SYMBOL

BUTTONS FUNCTION

Buttons are pressed two ways to execute functions:

1. Press and immediately release

2. Press and hold for at least two seconds

3. ON / OFF Button
   Press and release : Power on / off

4. Zero Button
   Press and release : Zero set for absolute measuring

5. ABS / – Unit Button

  * Press and release : Absolute and INC measuring mode conversion
  * Press and hold : Inch / Metric conversion ( ” in ” will appear for inch , “mm ” will appear for metric )
4. Button
  * Short press: After succesfully connection, shortly press DATA button to transfer measuring result
  * Long press: When working under wireless mode, press and hold DATA button to pair with connector

GENERAL SPECIFICATIONS

• Measuring force: 5-10N
• Operating temperature : 0-40
• Storage temperature : -20-60

PRODUCT USAGE

1. Press the ON / OFF (On/Off) key to illuminate the display. If the display shows “SET”, use the appropriate calibration post or block.Make a tight fit between the measuring surface and the surface to be measured, then twist the ratchet barrel so that it clicks three times. Finally press and hold ON / OFF and it will be set to the corresponding preset O position.
2. According to the measurement requirement, long press ABS / mm / in button to select the measurement unit.
3. When the measuring range is 0-25 mm and below, turn the ratchet barrel to close the two measuring surfaces of the micrometer, observe the displayed value and check whether the 0 position is correct.If the product exceeds the range of 25 mm, select the measuring calibration bar or block corresponding to the corresponding range, make the measuring surface and the measured surface fit closely, and select the measuring unit.If the product exceeds 2.5 mm range, select the measuring calibration bar or block corresponding to the corresponding range, make the measuring surface and the measured surface close together, observe the displayed value and check whether the O position is correct. When the O position of the product is not correct, press the ZERO key to reset the O position of the micrometer.
4. Rotate the ratchet barrel or micrometer barrel so that the measuring surface and the surface being measured fit closely together, then twist the ratchet barrel so that the ratchet barrel rattles three times. Then observe the display and read the value.

BATTERY USAGE AND INSTALLATION

Without any operation for more than 25 minutes, the screen is automatically off, rotating the sleeve can be turned on; without any operation for more than 72 H, then the systemPower off, you need to press ON / OFF power on, the screen appears “SET” characters, at this time, long press “ON / OFF” to reset the O position.2 . The product uses CR2450 batteries.3 . Using the supplied ‘S’ wrench, rotate the battery cover in a counterclockwise direction and remove. Then install the battery with the positive terminal facing up. Finally.

TROUBLESHOOTING

Measuring data incorrect| 1 . Dirty measuring faces 2 . Zero is incorrect| 1 . Clean measuring faces 2 . Inspect and reset zero
No display on LCD| 1 . Battery position is incorrect 2 . Battery is dead| 1 . Reset battery

2 . Replace with new battery

1 . Flickering display 2 . Display is sporadic

3 . Display remains dead

| 1 . Weak battery 2 . Weak battery

3 . Battery position is incorrect

| 1 . Replace battery 2 . Replace battery 3 . Reset battery
1 . Display is blurry

2 . Output data is incorrect

| Weak battery| Replace with new battery

PRECAUTIONS

• Do not subject the instrument to blows or shock. Do not drop it or apply excessive force.
• Do not disassemble the instrument.
• Do not press the keys with a pointed object.
• Do not use or store the instrument under direct sunlight.
• Avoid exposing the instrument away from strong magnetic fields and high voltage.
• Use a soft cloth to clean the instrument. Never use organic solvents such as acetone or benzene to clean.
• Clean measuring faces before use.
• If the instrument is to be stored or left unused for extended periods, remove the battery.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>