Maxxima MRL- S40905S 4 Inch and 6 Inch Square Slim LED Flat Panel Instruction Manual

Maxxima MRL- S40905S 4 Inch and 6 Inch Square Slim LED Flat Panel Instruction Manual

The units covered in these instructions are intended to retrofit Type IC or Type Non-IC luminaries.

Specifications

WARNING / ATTENTION

1. Risk of fire. Supply conductors (power wires) connecting to the fixture must be rated 90° C. If uncertain, consult an electrician.
2. Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaries electrical systems.
3. Risk of fire or electric shock. If not qualified, do not attempt installation. Contact a qualified electrician.
4. Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings.
5. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
6. This lamp is not intended for use with emergency exit fixtures or emergency lights.

CAUTIONS

1. For your safety read and understand instructions completely before starting installation.
2. Before attempting installation, check your local electric code, as it sets wiring standards for your locality.

NOTES

1. If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch.
2. Make sure no bare wires are exposed outside the wire nut connectors.
3. Do not make or alter any open holes in an enclosure of wiring or electrical components during kits installation.

Parts List

1. DRIVER/JUNCTION BOX
2. LIGHT PANEL
3. SPRING-LOADED CLIPS
4. CONNECTOR

Installation Guide

1. Turn off the power before installation. Remove the existing fixture if applicable.

2. Determine the location for installation and cut a ceiling hole with approximate dimensions as follows:

3. a. 4″ panel: 4.06” x 4.06″ (108mm x 108mm)

4. b. 6″ panel: 6″ x 6″ (152mm x 152mm) (Fig. 1)
   

5. Open the DRIVER/JUNCTION BOX cover and remove the appropriate knockout(s) on the side panel (Fig. 2). Install the appropriate cable clamp(s) (not included) and insert the electrical supply cable through the cable clamp. Connect the ground wire to the green wire terminal, hot wire to the black wire terminal and neutral wire to the white wire terminal using the wire nuts provided.
   

6. Place all wiring and connections back into the box and close the cover. Connect the DRIVER/JUNCTION BOX to the light panel using the CONNECTOR.

7. Insert DRIVER/JUNCTION BOX through the mounting hole (Fig. 3) and secure using mounting tabs.
   

8. Push the SPRING-LOADED CLIPS into the mounting hole upwards and insert LIGHT PANEL into it. Release the clips and the fixture will be pulled flush to the ceiling. (Fig 4)
   
   

WARNINGS AND CAUTIONS

• Risk of fire and electrical shock, products should be installed in accordance with appropriate electrical codes and regulations.
• The product shall be used together with an upstream air-gap switch.
• If you are unsure about any part of these instructions, consult a licensed electrician.
• DO NOT USE WITH AN IN-WALL DIMMER. Only Dimmable via the mobile APP.

Mobile APP Set-up

Step 1 Download the ‘TuyaSmart’ App

• Scan the QR code below to download the ‘TuyaSmart’ App.
• You can also download this app in the App Store/Android App Market, search “TuyaSmart”
  

Step 2 Register an account and Login

• Open the TuyaSmart App,click Register to create an account & login.
• If already registered, login.
  

Step 3 Selecting the Device

• Click ‘Add Device’ or the ‘ + ’ in the top right-hand corner;
• Click ‘lighting’ then ‘Light Source (Wi-Fi)’ to enter the device connection interface
  

Step 4 Mobile phone connection

Step 4a EZ mode connection:
When the Slim Panel is on, switch the on/off switch 3 times (each interval within 1s), Off, On, Off, On, Off, On. The light will flash quickly (flash once every second), your device can connect to the light. The light will stop flashing once when the connection is successful. If there is no connection, device will exit network configuration mode after 3 min.

• Enter the Network Name & WiFi password for your home, click Next.
• Confirm the light is flashing,click device indicator is ‘fast blinking (0.5S/time)’.
• Device will Connect.
  

Step 4b AP mode connection:
When the Slim Panel is flashing quickly; turn the light off. Repeat turn the on/off switch 3 times to make the light flash slowly. The light will flash slowly (flash once every 2-3s), your phone can connect to the light. The light will stop flashing once when the connection is successful. If there is no connection, the device will exit network configuration mode after 3 min.

• Enter the WiFi Network and password for your home, click ‘Next’.

• Click ‘EZ Mode’ in the upper corner to switch the interface to ‘AP Mode’.

• Confirm the light is blinking slowly, flashes slowly, click ‘Next’

• Back out of the APP, go to WiFi Networks in Settings, connect to the device WiFi – ‘SmartLife-XXXX.

• Return to the TuyaSmart App, wait for the connection to complete.
  
  

• Click to enter the operation interface.
  

Mobile APP operation

• Select White to adjust the CCT and to Dim.

• Select Color to adjust to the desired color, to Dim and adjust Contrast.
  

• Click Schedule to set a on or off function of the light at a certain time/day(s).

• Add schedule and then save. Repeat as desired.
  

• Select Left Time to enable Countdown Timer when light is on. The time selected will automatically turn the light off after the desired time.
  

• After the light connection is completed, it can be shared to many people, that is, one light can be controlled by multiple Users.

• Click to enter the device details interface;

• Click ‘Share Device’ to enter the device sharing interface.
  

• Click ‘Add Sharing’, add the account you are willing to sharing.
  

• You may also share all devices in your account with another account.

• Go to “Me” at the bottom of the App.

• Select “Home Management”.

• Select the Home you wish to share.

• Select “Add Member”. You can send invite via TUYA account, Message or Email. New Member must have or create a TUYA Account via the TUYA Smart App.

Support Amazon Alexa and Google Home Set-up

For Amazon Alexa

• Open Alexa App and select “Skills” from the top menu.
• On the Skills Page, search for TUYA Smart.
• Enable TUYA Smart in the Alexa App.
• Log in with your TUYA Smart account (username & password)
• Discover new smart devices in the App or ask Alexa to Discover new devices.

For Google Home

• Open Google Home App, tap “+” icon in the homepage.
• Select “Set up device” in the “Add and manage” screen.
• In the “Set Up” screen, tap “New Devices” to set up new devices in your home.
• Tap “Works with Google” to authorize Google Home to work with your TUYA Smart account.

Amazon Alexa and Google Home voice control examples

For Amazon Alexa

• Alexa,turn on
• Alexa,turn off
• Alexa,set to percent
• Alexa,brighten/increase
• Alexa,dim/decrease

For Google Home

• Hey Google,turn on
• Hey Google,turn off
• Hey Google,is on/off?
• Hey Google,brighten/increase by 50%

Trouble-Shooting / Recommendations / Tips

• If the light does not have an in-wall switch for on/off sequence for connecting to WiFi Network – before installing the slim panel downlight into ceiling, unplug the connector of the slim panel downlight from the J-Box to turn it off, plug the connector back in to turn on, and repeat. Please give 1-3 seconds between on and off. Once flashing, connect with mobile device. Once connected, finish installing the slim panel downlight into ceiling.
• If the light is offline in the App, make sure the in-wall switch is in the On position. If not, turn on.
• Please check whether the light is connected with power, and your mobile device is connected to a 2.4GHz WiFi Network.
• Check the router. If the router is dual-band, make sure to select 2.4GHz network to add the light. Router Broadcast should be set to open.
• Make sure the WiFi User Name and Password are correct.
• Make sure the light is within the range of the router signal. If not, try moving closer to the router. Check Wi-fi signal on the mobile device to make sure the signal is strong in that area or if it is weak.
• Check to see if the maximum number of devices/lights the router can handle has been reached. If so, remove a device/light and restart the router. If there is no Wi-Fi connection, try restarting the light and/or restarting the router.
• If the device will not go into pairing mode, try the on/off sequence 4 or 5 times instead of 3 times. Also give a second or 2 longer delay between the on/off sequence.
• If the internet signal/connection from the internet provider is down, the light can still be controlled through the mobile device as long as both are connected to the same Network (Intranet).

3 YEAR WARRANTY

Maxxima extends a 3 year limited warranty to the original purchase that the products listed are free from defects in material and/or workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION

Any changes or modifications to this unit not expressly approved by the manufacture could void the user’s authority to operate the equipment.

Support

info@maxximastyle.com
866-MAXXIMA (629-9462)
www.maxximastyle.com
125 Cabot Court Hauppauge, NY 11788

References

• Factory Direct LED Recessed Lighting, Outdoor Wall Lights, Ceiling Fixtures and Electrical Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>