VonHaus 3500102 5 in 1 DIY Workstation Instruction Manual
- June 4, 2024
- vonhaus
Table of Contents
VonHaus 3500102 5 in 1 DIY Workstation
SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
Safe operation of this accessory requires that you read and understand this manual carefully before use. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Keep children away from this appliance. Know your accessory. Read the operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this accessory. If any parts are missing, do not use the stand until the missing parts are replaced. NOTE This stand is designed for use with mitre saws and slide mitre saws with mounting dimensions not larger than 530mm.
NOTE
The maximum weight of the mitre saw and workpiece together must not exceed 150
kg. Do not modify or use this stand for any purpose for which it is not
intended. Always ensure the mitre saw used is mounted securely and is stable
before plugging in the mitre saw. This stand is designed to be used on a flat,
stable surface. Do not use the product on an uneven or unstable surface. Be
sure to allow enough room to handle and properly support the workpiece. Follow
the tool mounting instructions carefully, and ensure the tool is fastened
securely. To reduce the risk of injury from the mitre saw moving or falling
off the stand, always check that all mounting bolts and nuts are securely
tightened before moving the stand or using the tool. Do not lift any part of
the mitre saw that is attached to the stand. When servicing, use only
identical replacement parts. Use of any other parts may create a hazard or
cause product damage.Save these instructions. Refer to them frequently and use
them to instruct others who may use this accessory. ALWAYS KEEP WORK AREA
CLEAN Cluttered areas and benches invite accidents. Make sure the floor is
clean and not slippery due to wax or sawdust build-up. CAUTION The assembly
pack contains small parts which can pose a choking hazard to children and
pets.
COMPONENTS
Ensure All components are present. If any components are missing, do not
proceed with assembly. Contact DOMU Brands customer services at
hello@domu.co.uk
Part Description Qty
- Stand x1
- Handle x1
- M6 Nut x4
- M6x35 x2
- 5” Wheel x2
- Ø6 Washer x2
- Ø8 Washer x8
- M8 Spring Washer x8
- M8x16 x8
- Tool Mount x2
- Screw x6
- Swivel Wheel x2
- Top Tube x2
- Central Support x1
- Plastic Base x2
ASSEMBLY
WARNING Exercise caution. There is a potential for finger
pinch/entrapment.
- Lay the stand (A) top surface on the floor
- Press the Leg Lock Lever and lift leg until the lever clicks into place
- Use M8x16 bolt (I) and Ø8 Washer (G) to assemble the Swivel Wheels (L)
- Lift the stand
- the M6 Nut (C) and Ø6 Washer (F) to assemble 5” Wheel (E) to the axle.
- the M6x35 Bolt (D) and M6 Nut (C) to assemble the Handle (B).
- Insert the Top Tube (M) into the Plastic Base (O) and fix with the Screws (K)
- Attach the Central Support (N) to the Top Tube (M) with the Screws (K)
- Put the assembled worktop onto the stand and fix it by the 4 lock catches.
SETTING THE HEIGHT
- Clench the button inside and pull the bench up and down to adjust to the desired height.
- Ensure the locking pin locks securely at the new height.
MOUNTING A MITRE SAW TO THE STAND
- Unplug the saw and the saw arm in the downwards position.
- Place a tool mount underneath the saw, aligning the mounting holes on the mitre saw base with the slot in the top of the tool mount.
- Fix the carriage bolt up through both the tool mount and the mounting hole ion the saw.
- Secure in place using a flat washer. Lock the washer and nut, and repeat through the other end of the tool mount.
- Use the Handles located at the rear of the tool mounts to aid in installing or removing saw and bracket assembly
- Lift the saw and tool mount assembly, allowing the assembly to tilt slightly toward your body
- Hook the front edge of the tool mount assembly onto the front rail of the stand.
- Lower the tool mount assembly to allow the rear edge of the tool mount to seat fully over the rear rail
UNMOUNTING A MITRE SAW FROM THE STAND
- Raise the Locking Levers (J) to unlock the saw and the tool mounts
- Grasp the handles on either side of the assembly and lift away from the rear rail of the stand to disengage
- With the assembly tilted slightly toward you, lift the front part of the assembly to disengage from the front of the rail stand
FOLDING THE STAND
Press the Locking Lever until the legs are fully folded
CLEANING & MAINTENANCE
Keep the Stand clean by wiping it down with a clean damp cloth and store in a
dry place when not in use. Before storing or transporting make sure all
attachments are secure and the benchtop tool is removed. Collapse extension
rails.
The stand can be transported by grasping the handle with one hand and wheeling
in the same manner as a wheelbarrow.
DISPOSAL INFORMATION
Please recycle where facilities exist. Check with your local authority for
recycling advice.
CUSTOMER SERVICE
If you are having difficulty using this product and require support, please
contact hello@domu.co.uk
WARRANTY
To register your product and find out if you qualify for a free extended warranty please go to www.Vonhaus.com/warranty. Please retain a proof of purchase receipt or statement as proof of the purchase date. The warranty only applies if the product is used solely in the manner indicated in the Warnings page of this manual, and all other instructions have been followed accurately. Any abuse of the product or the manner in which it is used will invalidate the warranty. Returned goods will not be accepted unless re-packaged in its original packaging and accompanied by a relevant and completed returns form. This does not affect your statutory rights. No rights are given under this warranty to a person acquiring the appliance second-hand or for commercial or communal use.
COPYRIGHT
All material in this instruction manual is copyrighted by DOMU Brands. Any
unauthorised use may violate worldwide copyright, trademark, and other laws.
THANK YOU
Thank you for purchasing the 5-in-1 Workstation VonHaus is a registered
trademark of DOMU Brands Ltd Made in China for DOMU Brands Ltd M24 2RW.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>