carrello CRL-8510-1 Epica 2 In 1 Pushchair Instruction Manual

June 17, 2024
Carrello

CRL-8510-1 Epica 2 In 1 Pushchair
Instruction Manual

CRL-8510-1 Epica 2 In 1 Pushchair

carrello CRL-8510-1 Epica 2 In 1 Pushchaircarrello CRL-8510-1 Epica 2 In 1
Pushchair - figcarrello CRL-8510-1 Epica 2 In 1
Pushchair - fig 2carrello CRL-8510-1 Epica 2 In 1
Pushchair - fig 3carrello CRL-8510-1 Epica 2 In 1
Pushchair - fig 4carrello CRL-8510-1 Epica 2 In 1
Pushchair - fig 5carrello CRL-8510-1 Epica 2 In 1
Pushchair - fig 6

Thank you for choosing the product of T.M. “CARRELLO”.
This instruction manual contains important information about assembly process, safety regulations and maintenance of the stroll­er.
Please read these instructions carefully before use and keep them or later reference. The safety of your child could be put at risk if you do not follow these instructions.

NAME OF PARTS

  1. FRAME*1
  2. SEAT*1
  3. Rear wheels*2
  4. FRONT WHEELS*2
  5. BUMPER*1
  6. CANOPY*1
  7.  CARRY COT*1
  8.  CARRY*1

carrello CRL-8510-1 Epica 2 In 1 Pushchair - fig 8

WARNING

WARNING: Leaving the baby without care may cause a danger
WARNING: Do not use an additional mattress in the product.
WARNING: Before use be sure that the assembling mechanisms are blocked
WARNING: Always use the crotch belt together with the help belt.
WARNING: This product is not designated to go roller blades or to run.
WARNING: This stroller is indented to bear only one baby.
WARNING: This stroller is designated for the babies up to 0-36 months and weight 15kg
WARNING: Do not leave the stroller with a baby on the slope, even if the brake is locked.
WARNING: Do not use the stroller, if any component is damaged.
WARNING: During the assembling and disassembling the stroller, be sure that the baby is at the safe distance
WARNING: Making any adjustments, make sure that the movable parts are not close to the baby’s body.
WARNING: Always lock the brake when stops.
WARNING: Maximum load of basket is 3 kg
WARNING: Every bag or other load handing or the handle affects its stability.
WARNING: Only the original parts, confirmed by the producer should be used in this product.
WARNING: Do not drive the stroller through the stairs
WARNING: The stroller should be kept away from babies

ASSEMBLY AND OPERATING INSTRUCTIONS

2. OPEN THE STROLLER:
2a.Lift the handle up as pie 2a ;
2b.when the stroller is opened as pie 2b, you should hear “click” sounds on both side of the stroller, please examine if the stroller is locked in safety position before you use it.
3. ASSEMBLE/DISASSEMBLE REAR WHEELS :
3a.To assemble the rear wheels: Take one side of rear wheels, Insert the rear axle into the plastic hole as picture 3a, until it is locked, install the other side of the rear wheel in the same way.
3b.To disassemble the rear wheels: Pull the rear wheel express iron as arrow 1, remove the rear wheel in the direction of arrow 2 then finish the disassemble
4. ASSEMBLE/DISASSEMBLE FRONT WHEELS :
4a. To assemble the front wheels: Take one side of front wheels, insert the vertical shaft into the plastic hole on the wheel seat as pie 4a, until it is locked, install the other side of the front wheel in the same way
4b.To disassemble the front wheels: press the small metal pins as arrow 1, at the same time use your hand to pull out the front wheel as arrow 2 to finish disassemble
5a. The front wheels 360 degree rotationz
Lift up the plastic button on the front wheels to lock it not rotated at 360 degree, press down the plastic button to release it can be rotated at 360degree as the arrow in the pie 5a. 5b.Brake the stroller Step down the brake pedal to brake the stroller, lift up the pedal to release the brake 5a pie 5b warning : Always lock the brake when put or carry a child
6.ASSEMBLE THE SEAT
Assemble the seat as picture 6(back to mother), you should hear a “click” sounds on both side to make sure the seat is locked in safety position.
To reverse the seat in different direction (face to mother) in same way.
7. a.Assemble the bumper
Insert the bumper on both sides of the seat as picture 7a.
7b.Disassemble the bumper
Press the button as arrow 1 in picture 7b to remove the bumper.
8a.Assemble the hood
Insert the hood plastic into the seat as pie 8a. 8b.Open and fold the hood
Extend or fold the hood as pie 8b
9.Telescope handle bar
Press the button as the arrow 1 in pie 9
10a.Adjusted the footrest
Press the button as arrow 1 in the pie 10 to adjust the footrest in 3 position
11a.Adjusted the backrest
Lift up the button as arrow1 in the pie 11a to adjust the backrest to be in 3 posi­ tion(sleeping or seat) as pie 11b.
12a.Reversible seat
Pull out the button and lift up the seat as arrow direction in pie 12a, then assemble the seat in opposite direction as picture 12b, insert the seat in the frame to finish the assemble
13. folding the stroller :
When the seat face to the mother, fold the backrest to the handle side as 13a When the seat back to the mother, fold the seat to the handle side as 13b Then press and hold the button as arrow 2 not released, in same time lift up the carry handle as arrow 3 in the pie 13c, finally release the button to fold the stroller as pie 13d.
14a-b. Use the safety belt
Pie 14a-14b: There are 2 position for safety belt, the up position is suitable for one baby more than 6 months, the bottom position is suitable for one baby under than 6 months
14c.Use the safety buckle
Click here to lock the safety buckle on both sides as 14c,Press the middle button to release the safety button as 14c
You can adjust the length of the seat belt by pulling the safety buckle on both sides as needed
Assembly/Disassembly of the carrycot:
In order to unfold the carrycot, remove the bedding and the mattress, and then  squeeze the metal tensioners on the bottom plate of the carrycot in the direc­ tion of the arrows, until it Locks in special holders. You should hear a “click” sound, indicating the Locking of the tensioner in the holder. NOTE! The pram body is designed for children up to 6 months old weighing up to 9 kg, which cannot sit, kneel or trundle by themselves. Do not use the carry­ cot if your child starts sitting up, kneeling or trundling by itself. WARNING: Do not use an additional mattress of thickness of more than 15mm.
Assemble every spare parts for the carrycot.
The carrycot canopy has a 4-step adjustment. In order to adjust the canopy to the desired position, simultaneously press the buttons Located at the base of the canopy tube. You can extend the canopy by pulling the canopy tube. The canopy tube is also a carrying handle. In order to move the carrycot by the handle, place it n the top position.
NOTE! Make sure that the carrying handle is Locked in the correct position before you move the carrycot.
Insert the adaptor into the stroller frame until you hear the “click” sound which means the higher adaptor is Locked.
Insert the carrycot in to the stroller frame in the direction keeping the babies face visible to the adult. Align the carrycot with the adaptor right above the stroller frame, push down until you hear the “click” sound indicating that the carrycot s properly installed in the stroller frame.
NOTE! The pram body can be assembled only against the direction of travel (in this setting, the person pushing the stroller is facing the child)
NOTE! Lock the safety brake before you assemble carrycot on the stroller frame.
Press down the memory buttons on both sides and pull up the carrycot then take off the carrycot. You can press down the release buttons one by one.
NOTE! Before using, make sure that the stroller body is properly assembled.
NOTE! Lock the safety brake before you remove the carrycot.
The carrycot has a back rest inside, you can choose to use or not to use it. If you use the back rest, you can fix the backrest only in the plastic groove. Never fix the backrest on the metal tensioner.
CARE AND MAINTENANCE
This product requires regular care. Cleaning and care operations must be performed by an adult.

  • Upholstery of the stroller is not removable. The tissue parts should be cleaned ith a damp sponge and neutral soap, following the washing instructions on the product labels.
  • Regularly wipe the plastic parts with a damp cloth
  • After contact with water, wipe the metal parts dry to prevent formation of rust.
  • If necessary, lubricate the moving parts with dry silicone oil.
  • Regularly check the wear condition of the wheels and clean them from dust and sand.
  • In order to avoid friction that can adversely affect the work of the stroller, prevent the accumulation of dust, dirt and sand on plastic parts that are moving through metal tubular structures.
  • Keep the cart in a dry place.
  •  The metal parts can be cleaned with a damp cloth. After cleaning, wipe it dry to prevent corrosion.
  • The stroller can be cleaned with a damp cloth using a delicate detergent. After cleaning, the stroller should be dried in the unfolded form in a place where the product will not suffer the long-term exposure to sunlight and where ventilation is present.
  •  Do not use bleach.
  • Do not allow prolonged exposure of the product to sunlight.
  •  Clean wheels, brakes and items that have sand or other contaminants regularly cleaned.
  •  Store in a dark place out of the reach of children.

carrellobaby.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals