Sofucor KBS-52K096SMTY 52 Inch Smart Ceiling Fans with Lights User Guide

Sofucor KBS-52K096SMTY 52 Inch Smart Ceiling Fans with Lights

Safety Information

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SANE INSTRUCTIONS.

Warning:

Kindly turn off the power when connecting cables.

1. To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code ANSINFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9 kg) Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs. (15.9 kg) or less”
4. The fan must be mounted with a minimum of 7 ft. (2.1 m) clearance from the trailing edge of the blades to the floor.
5. Do not place objects in the path of the blades.
6. To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be Ul-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
8. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
9. All setscrews must be checked and re-tightened where necessary before installation.

WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.
WARNING: To reduce the risk of fire or electric shock, this fan is NOT suitable for use with solid-state speed controls.
WARNING: To avoid possible electrical shock, make sure that the electricity is turned off at the main power box before starting work. If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan
WARNING: To reduce the risk of fire, electrical shock or personal injury, ensure that the fan mounting bracket is supported directly from the building structure or the outlet box marked “Acceptable for Fan Support of 35 lbs. (15.9 kg) or less”. Use only the screws provided with the outlet box.
WARNING: Do not short-circuit, disassemble, heat up, connect improperly, or dispose of used batteries in fire. Do not recharge or mix batteries with used or other battery types. Immediately remove used batteries
WARNING: Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body it can cause severe internal burns and can lead to death in as little as 2 hours Always completely secure the battery compartment.If the battery compartment does not close securely stop using the product. remove the batteries and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body. seek immediate medical attention
WARNING: a) The cells shall be disposed of properly including keeping them away from children; and b) Even used cells may cause injury.tion
WARNING: Do not test the fan before affixing the blades. The DC motor needs a load to rotate properly. Affixing blades and then testing the fans.

Warranty

The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time. of shipment from the factory for a period of two years after the date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and re-installing the product are your responsibility. Damage to any part such as by accident, misuse, improper installation, or by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing, or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Sofucor hereby disclaims any and all warranties, including but not limited to those of merchant ability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.

Three ceiling installation methods

Concrete Ceiling Mounting Bracket

Hanger for Junction Box Mounting Bracket

Wooden ceiling Mounting Bracket

Accessory drawing

Installation procedure

1. Place one blade on the motor and align the screw holes
2. Place the reinforcement gasket on the blade
3. Tighten the blade screws
4. Place the other blades one by one and tighten the screws
5. Loosen and remove the 3 silver lamp panel screws pre-locked on the motor(They will be needed later)
6. Put on the lamp panel and feed the wire plugs through the center hole
7. Tighten the 3 silver lamp panel screws
8. Loosen and remove the 3 brass light kit screws pre-locked on the lamp panel(They will be needed later)
9. Connect the light source with the wires from the motor
10. Align the screw holes and tighten the 3 brass light kit screws
11. Turn the fan over
12. Loosen the 2 brass screws pre-locked on the top of the motor
13. Remove 2 screws on the hanger ball
14. Remove the lock pin and the bolt of the base of the downrod
15. Select one downrod and pass all motor wires/light cables through it
16. Insert the bolt
17. Fix the bolt with the lock pin
18. Tighten the 2 screws to prevent fan shaking during operation
19. Put the decorative cover through the downrod
20. Put the canopy cover through the downrod
21. Put the canopy through the downrod
22. Put the hanger ball through the downrod
23. Insert the bolt
24. Fix the green ground wire with screw. Align the screw hole and tighten the screw
25. Insert another screw and tighten the screw
26. Connect the wire from the ceiling fan to the receiver(Blue and White wires)
27. Connect the wire from the ceiling fan to the receiver(Red, White and Black wires)
28. Install the ceiling bracket with four self-tapping screws
29. Place the downrod ball into the slot in the ceiling bracket. If the slot doesn’t align properly then rotate the ball
30. Use wire connecting nuts to connect the two ground wires(Green)coming from the downrod and hanging bracket
31. Put the receiver into the mounting bracket
32. Lift the canopy into place so that the screw holes are aligned
33. Wrap keyhole slots around the screws, twist clockwise and tighten 2 screws
34. Lift the canopy cover to the canopy
35. Install the lampshade and rotate it to lock

WARNING:

Turn off the electric power during installation and make wire connection.

1. Connect the wire from the ceiling fan into the receiver.
2. Connect the wire from the receiver with the wire from the house.

Remote control manual

Connect to app settings:

If you power on the fan for more than 3 minutes, you will not be able to search for the device.At this time, you need to reset your fan:turn fan power Off and back on at the wall switch， within 30 seconds,press the “POWER” button for 5 seconds to reset. If the reset is successful,the light flashes,then add the Device again.

After the reversible button is pressed, the fan slowly slows down to a stop. And then it started to reverse.

Fans Balance

if it does not work

1. Turn on the main switch.
2. Setting the codes on the receiver: The Learn Key must be pressed within 5 seconds,after pressing the Power button. If not,please press the Power button to restart.Keep pressing the button LEARN key in excess of 3 second it becomes a LEARN status.
3. The receiver Can remember the last code’s status. The ceiling fan light flash two times.

Care and Cleaning

• Slide the balancing clip on the trailing edge of any blade, halfway between the holder and tip. Run the fan to check the wobble. If the wobble persists, repeat with each blade, noting which one most reduced the wobble.
• Slide the clip in small increments away from the center of that blade. Move the clip, operate the fan, then move it again until you eliminate as much wobble as possible.
• Stick the adhesive-backed balancing weight on the top center of the blade directly in line with the balancing clip.Add more weight if needed to get a smooth-running fan.

WARNING: Make sure the power is off before cleaning your fan.

• Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
• Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discolouration or tarnishing.
• You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish. The motor has permanently lubricated sealed ball bearings.

Troubleshooting

The fan will not start.

| □  Check the main and branch circuit fuses or breakers.

□  Check the line wire connections to the fan and switch wire connections in the switch housing.

The fan is noisy.

| □  Ensure all motor housing screws are snug.

□  Ensure the screws that attach the fan blade bracket to the motor hub are tight.

□  Ensure the wire nut connections are not ratting against each other or the inter or wall of the switch housing.

□  Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.

□  If you are using the Ceiling Fan light kit.ensure the screws securing the glassware are tight.Check that the light

□   bulbs are also secure.

□  Ensure the canopy is a short distance from the ceiling.It should not touch the ceiling.

□  Ensure your outlet box is secure and rubber isolator pads wereused between the mounting plate and outlet box.

The fan wobbles.

|

□ Please check and follow the instructions: Chapitre No.13 Fan balance on page 16.

If you have any questions, please contact us. We will help you solve any problem.

• Email:sofucor_service@163.com
• Email:sofucorceilingfan@163.com

Connecting Smart Systems

• Connecting with Moble Phone APP
  Search for “Smart Life” in the App store or can the QR code to download the “Smart Life” app

• Register and log in APP
  After downloading and opening the APP, register and log in the APP according to the options.

• Add smart devices
  Add smart devices, and ensure WIFI 2.4GHz and Bluetooth are stably connected in subsequent scanning and connection. 5GHz and 5.8GHz are not supported

• Initial automatic scan for connected devices
  Within 30 seconds after the fan is powered on, hold down the remote fan switch for 5S, the LED light source blinks once, and the fan is turned on intelligently.

• Select the scanned fan
  Select the fan to be connected.

• APP connection to WIFI
  Enter the connected WIFI name and password.

• The fan is paired with the APP

1. After pairing is complete, you can customize the fan name.
2. If pairing fails, first check whether the connected WiFI name and password are correct. If the connection fails for many times, you can try to manually find the fan and select 8 to start.![Sofucor-KBS-52K096SMTY-52-Inch-Smart-Ceiling-Fans-with-Lights-fig-40](https://manuals.plus/wp-content/uploads/2024/02/Sofucor-KBS-52K096SMTY-52-Inch-Smart-Ceiling-Fans-with-Lights-fig-40.jpg)

• Open the fan connection manually
  Select “Fan” in “Lighting” (Bluetooth +WIFI).

1.  **Follow the prompt**
  1. Confirm the indicator is blinking or breathing.
  2. Select the status of the indicator light.![Sofucor-KBS-52K096SMTY-52-Inch-Smart-Ceiling-Fans-with-Lights-fig-42](https://manuals.plus/wp-content/uploads/2024/02/Sofucor-KBS-52K096SMTY-52-Inch-Smart-Ceiling-Fans-with-Lights-fig-42.jpg)
2.  **Follow the prompt**
  1. Select 2.4 GHz Wi-Fi network and enter a password.
  2. Connect your mobile phone to the device’s hotspot.
  3. Device Adding Timeout, Check demerit points and retry.
  4. Follow the picture instructions to set up the device.![Sofucor-KBS-52K096SMTY-52-Inch-Smart-Ceiling-Fans-with-Lights-fig-43](https://manuals.plus/wp-content/uploads/2024/02/Sofucor-KBS-52K096SMTY-52-Inch-Smart-Ceiling-Fans-with-Lights-fig-43.jpg)
3.  **Manually finding a fan is complete**  

Manually find the fan successfully, and start the connection (refer to 7 ).

• Connect successfully and enter the control interface
  According to the interface, free adjustment.

Link skill to the Amazon Echo or Google Assistant

In the App, change the name of the device to an easily identifiable name such as bedroom light, or bedroom fan. Make sure your Amazon Echo device is powered on and connecting to your home Wi-Fi network.

Common commands

• A Fan:
• Alexa, tum on/off < DEVICE NAME>.
• Alexa, what is the < DEVICE NAME > speed?
• Alexa, set the < DEVICE NAME > speed to 1/2/3/4/5/6.
• Alexa, setthe bedroom speed to max.
• Alexa, turn up/decrease the bedroom speed
• Alexa, set the < DEVICE NAME > to foward/reverse.
• Alexa, is < DEVICE NAME > on on?
• Alexa set the mode on the to fresh/nature.
• Alexa set the count down on the < DEVICE NAME> to cancel/1 hour/2 hour/4 hour/8 hour.
• Light: < device name>
• Alexa, tum on/off ‹device name>.
• Alexa set the to fifty percent.
• Alexa, make the warm white/white/cool white.
• Alexa, brighten/dim < device name>.

Questions or Support?

• Email:sofucor_service@163.com
• Email:sofucorceilingfan@163.com
• www.sofucorfan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>