solution fires LUX75 Cassette Fires Instruction Manual

solution fires LUX75 Cassette Fires

Product Information

Specifications

• Product Models: LUX75, LUX75XH, LUX100, LUX125, LUX150, LUX175, LUX200
• Type: Cassette Fires
• Suitable for: Well insulated spaces or occasional use
• Compliance: European Safety Standards EN60335-2-30, European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3
• Requirements: Must be installed in accordance with current Standards and Local Codes
• Website: www.solutionfires.co.uk
• Manual Version: Jan 2024 – V1.6
• EEC Directives Compliance: 2006/95/EC and 2004/108/EC

Important Safety Advice
When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• WARNING: If the appliance is damaged, check immediately with your retailer before installation and operation. The heater must not be used if any part of it is damaged.
• Do not use outdoors.
• WARNING: In order to avoid overheating, do not cover the heater. The appliance carries the Warning Symbol indicating that it must not be covered or has.

Product Usage Instructions

Electrical Connection
This appliance is supplied with a power lead complete with a moulded 13 Amp UK three-pin plug to connect into a standard UK socket outlet or European equivalent. This appliance must be earthed. The plug must be easily accessible after siting the appliance. Should a new fuse be required, consult a competent person to establish the reason for the fuse operating. Only once the fault is rectified should a new 13A fuse be inserted into the plug.

Cleaning
Use only a dry duster or vacuum cleaner with brush attachment to clean the appliance. Never use abrasive cleaners, water, steam cleaners, or aerosols on or near the appliance.

Control
Only control the appliance using the manual operations, the supplied remote control described in this manual, or the Solution Fires app. Do not use this heater with a programmer, timer, separate remote control system, or any other device that switches the heater on automatically.

Battery Handling
Only adults should handle the batteries. Do not allow a child to use the remote control unless the battery cover is securely attached to the battery compartment. All batteries must be disposed of at your local recycling point.

Installation

Please check that the following components are included within the box. If anything is missing or damaged, please contact the retailer and do not use the appliance until you have everything.

• Appliance with trailing lead with moulded 13 Amp plug
• Remote control hand set and batteries
• Fixing brackets, side plaster beads, and furniture guides
• Grille cover panel
• Instruction manual
• Glass removal mini suction cup

Front Glass Removal (Caution – wear suitable gloves when handling glass)

1. Remove the glass retaining brackets on the left and right sides of the grille panel.

FAQ

Q: Can I use the product outdoors?
A: No, the product is not suitable for outdoor use.

Q: Can I cover the heater?
A: No, the heater must not be covered to avoid overheating. The appliance carries a warning symbol indicating that it must not be covered.

Q: How should I clean the appliance?
A: Use only a dry duster or vacuum cleaner with a brush attachment. Never use abrasive cleaners, water, steam cleaners, or aerosols on or near the appliance.

Q: Can I use a separate remote control system with this heater?
A: No, do not use this heater with a programmer, timer, separate remote control system, or any other device that switches the heater on automatically. Only use the manual operations, supplied remote control, or Solution Fires app to control the appliance.

This product is only suitable for well insulated spaces or occasional use. To be left with the customer after demonstrating the features of the Solution electric fire.
The complete installation must be carried out in accordance with current Standards and Local Codes. The instructions in this manual must be followed to ensure safe operation of the appliance. It should be noted that the requirements and this publication may be superseded during the life of
the Fireplace – please refer to www.solutionfires.co.uk for up-to-date instructions.

Jan 2024 – V1.6

The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC

Important Safety Advice

When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
WARNING: If the appliance is damaged, check immediately with your retailer before installation and operation. The heater must not be used if any part of it is damaged.
Do not use outdoors. WARNING: In order to avoid overheating, do not cover the heater. The appliance carries the Warning Symbol indicating that it must not be covered or has
a do not cover label. Do not cover or obstruct in any way the heat outlet grille located above the window of the appliance. Do not place material or garments over the front of the appliance as this could cause overheating and a fire risk. In the event of a fault unplug the heater. Unplug the appliance when not required for long periods. This appliance can be used by persons if they have been given instruction concerning use of the appliance in a safe way or are supervised and understand the hazards involved. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge if they have been given instruction or supervision concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be carried out by children without adequate supervision. Children of less than 3 years should be kept away from the appliance unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given instruction or supervision concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate or clean the appliance or perform user maintenance on the appliance. If the supply cord is damaged, switch off the mains power at the wall socket immediately. WARNING: The heater must not be located immediately below, above or in front of a fixed socket outlet or electrical connection box. WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. CAUTION: Some parts of this appliance around the heater grill can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present. The heater must not be positioned or used where it may come into contact with water, for example but not exclusively, in wet rooms, bathrooms, swimming pools, laundries or used to dry clothes. Do not use the appliance in rooms with explosive gas (e.g. petrol) or while using inflammable glue or solvent (e.g. when gluing or varnishing parquet floors, PVC etc.) Do not insert any objects into the appliance. This appliance must be connected to a 220-240VAC 50-60Hz supply. If the supply cord is damaged, it must be replaced by the manufacturer, its agent or a similarly qualified person in order to avoid a hazard.
03

This appliance is supplied with a power lead complete with a moulded 13 Amp UK three-pin plug to connect into a standard UK socket outlet or European equivalent. This appliance must be earthed. The plug must be easily accessible after siting the appliance. Should a new fuse be required, consult a competent person to establish the reason for the fuse operating. Only once the fault is rectified should a new 13A fuse be inserted into the plug.
Use only a dry duster or vacuum cleaner with brush attachment to clean the appliance. Never use abrasive cleaners, water, steam cleaners or aerosols on or near the appliance.
Only control the appliance using the manual operations, the supplied remote control described in this manual, or the Solution Fires app. Do not use this heater with a programmer, timer, separate remote control system or any other device that switches the heater on automatically.
Only adults should handle the batteries. Do not allow a child to use the remote control unless the battery cover is securely attached to the battery compartment. All batteries must be disposed of at your local recycling point.
Please check that the following components are included within the box. If anything is missing or damaged, please contact the retailer and do not use the appliance until you have everything.
Appliance with trailing lead with moulded 13 Amp plug. Remote control hand set and batteries. Fixing brackets, side plaster beads and furniture guides. Grille cover panel Instruct ion manual. Glass removal mini suction cup. Installation – Front Glass Removal (Caution – wear suitable gloves when handling glass) 1. Remove the glass retaining brackets on the left and right sides of the grille panel.
Remove screws
2. Place the suction cup on the glass, in the middle, near the top. Press the suction cup to expel air, then gently pull forward to release the glass.
3. Carefully lift the glass out by hand. Do not attempt to lift the glass with the suction cup.
04

Installation & Operating Instructions

Installation Requirements: Before commencing installation of the unit consideration should be given to the following: 1. Read these instructions thoroughly. 2. You will need suitable tools (e.g. drill and drill bits, screwdrivers, spirit level, tape measure). 3. Select a location that is not prone to moisture. 4. A 13 amp, 240 Volt socket or switched, fused spur capable of accommodating a maximum load of
2050 watts must be available close to the appliance. The socket must be accessible at all times and must not be placed directly behind the unit. Ensure that the circuit and associated breaker are sized for the connected load. 5. This product has been designed to be installed into a plaster board, or existing chimney breast. 6. Please seek advice from a professional, with reference to the structural integrity of the installation site. 7. If the product is to be installed into an open chimney or flue, it is important that the chimney flue is partially blocked to prevent any up/down draughts and falling debris, but does not restrict or alter the airflow to the product. 8. Ensure that the product has a minimum internal clearance directly above the grille cover of 100mm, this is to ensure that the product can circulate the required airflow for the heater unit. 9. The product should never be sealed into an opening with the use of silicones or adhesives as this
10. DO NOT SCREW ANY FIXINGS INTO THE BODY OF THE FIRE TO MOUNT ANY FURNITURE OR OTHER PARTS NOT SUPPLIED WITH THE FIRE.
11. THE BRACKET SUPPLIED IS TO SUPPORT THE WEIGHT OF THE APPLIANCE ONLY. THE APPLIANCE IS NOT DESIGNED TO BEAR ANY ADDITIONAL LOAD.
12. ENSURE THAT THE FAN HEATER IS ADEQUATELY VENTILATED.
independently supported.
1. Carefully remove the unit from the packaging and prior to installing the unit, test the unit by plugging the power supply into a conveniently located 13 amp earthed socket.
2. Your product is supplied with one or more wall mounting brackets. (Dependent on model)
the wall construction, plaster board or solid wall.

686mm (27″) – LUX100, LUX125, LUX150, LUX175, LUX200
787mm (31″) – LUX75

Fig.3

Fig.4

The fire is designed to be permanently fixed to a wall at a suitable height, the wall bracket must be fitted horizontally and the cable routed to the bottom right of the fire. A height of 686mm (LUX100, LUX125, LUX150, LUX175, LUX200), 787mm (LUX75) or 1333mm (LUX75XH) from the floor to the bottom of the bracket is suggested. You will need to calculate the height of the bracket if the fire is being fitted into a suite or purpose-made chimney breast.
05

Installation Instructions

Installation – Continued: 5. Install the grille cover panel over the top grille opening. Remove the wall brace brackets, then lift and hook the fire onto the wall.
Grille cover
Wall brace brackets

6. Fix the wall brace brackets ready to secure to the wall.

7. Once the product is secured to the wall and connected to the power supply, the false construction such as plaster board wall or chimney breast can be formed around it.
8. The product is also designed to allow a platform to support it.

Scene Light Kit and Scene Spot Light Kit
If you are using a scene lighting kit, ensure the kit is plugged into the external power socket on the fire before building the appliance into any fireplace or suite (image below). The maximum connected load is 12V DC, 5A and only genuine Solution Fires parts may be connected. The LED strip lights supplied with your Scene Light Kit or Scene Spot Light Kit are the maximum allowable length. Refer to the Scene Light Kit or Scene Spot Light Kit instructions for further details.
Note: Ensure all power is off during the installation process.
CAUTION: Care must be taken to avoid over bending the connector cable or overtightening the connector, as this can damage the internal wires.
06

Installation Instructions

Installation – Continued: The LUX Cassette Fires are designed for four different installation types. Installation -Option 1 – Front View

Option 1

NOTE:
No screws or fixings for the furniture surrounding your fire may be fixed to the fire. This will invalidate your warranty.

Remove the furniture guides and recycle when installing the fire as shown in Options 1-4

Model

A

LUX75

750mm

LUX75XH 750mm

LUX100 1000mm

LUX125 1250mm

LUX150 1500mm

LUX175 1750mm

LUX200 2000mm

B

C

D

581mm 737mm 226mm

1250mm 1434mm 226mm

428mm 585mm 226mm

428mm 585mm 226mm

428mm 585mm 226mm

428mm 585mm 226mm

428mm 585mm 226mm

E
334mm 334mm 334mm 334mm 334mm 334mm 334mm

F
83mm 83mm 83mm 83mm 83mm 83mm 83mm

G
82mm 82mm 73mm 73mm 73mm 73mm 73mm

The above table contains the minimum opening
A = B = C = D = E = F =
G = Height from underside of foot to underside of lower plaster flange

F

C

Remove furniture

G

guides

G

07

Installation Instructions
Installation – Option 2 & 3 – Left or Right Corner View: Remove one steel side panel by removing screws before installation.

Installation Instructions
Remove 2 steel side panels by removing the screws before installation.

Fix the side plaster brackets and put all the screws back onto side panels.

Fix the side plaster brackets and put all the screws back onto side panels.

Replace all screws that have been removed. Option 2

Note: Remove furniture guides for this option.

Option 3 08

Note: Remove furniture guides for this option.

Option 4
Alternative – Floating Base securely to the wall.
Furniture Guides Furniture Guides on Front & Sides
(Adjustable for material 10-25mm thick)

are not for support, ensure all furniture work is independently supported. Remove furniture guides for this option.
Included in box optional decorative side panels

Operating Instructions

Fig.19

MANUAL CONTROL PANEL

FIRE ON/OFF BUTTON

HEATER

MANUAL POWER ON/OFF SWITCH

INDICATOR

The unit can be operated on the manual control panel and with the supplied remote control. For the unit to operate, the manual ON/OFF switch, located on the right side of the control panel must be switched to the “I” position. An indicator light will illuminate when the fire is plugged in and the manual ON/OFF switch is in the “I” position. The light will go OFF once the manual power ON/OFF switch is pushed to ON.
Indicator Light The indicator light has 4 functions as follows: 1 – Confirmation that power is reaching the fire from the house supply – continuously on until the fire is turned on. 2 – The indicator is a red light if NOT connected to Wi-Fi. Once the fire has connected to a Wi-Fi network, the indicator turns green. 3 – Indication of when the open window device has operated – blinks on for 0.5 seconds and off for 0.5 seconds until the window/door is closed and the heater is turned back on. 4 – Display current heating level, if the fan is on and the light is Amber, the heating is on Low, if the fan is on and the light is Red, the heat is high. If the fan is running and the light is off or green, the heater is cooling down. Use the manual control panel on/off button to turn your fire on or off. Use the Heater button to switch heater Low, High, or Off.
NOTE: The unit may emit a slight, harmless odour and smoke when first used. This odour & smoke is normal and it is caused by heating the internal heater parts and will not occur again. NOTE: Ensure the manual ON/OFF switch located at the top of the front glass on the right hand side is switched to the “I” position. NOTE: Before attempting any operation with the remote, press and slide the battery door (on the back of remote) open and insert two AAA batteries, checking that the + and – ends of the battery match inside the battery compartment, close the battery door.
Powering the Fireplace Press the fire on/off button to turn on the fire. Press the Power button again to turn off the fire. NOTE: All previous settings are held in memory, so the next time you power up the fireplace, the unit will turn on with the same settings.
Remote Control Buttons Heater LOW/HIGH/OFF “Heat” Press the Heater button on Remote Control to cycle through Low heat, High heat and turning the Heater off. NOTE: As an additional safety feature, the heater will turn off after 12 hours continuous operation in case it has been left on by mistake.
10

Operation Continued
Remote Control Buttons
Power on/off Pre-set
Downlight
Heat Dimmer -/Minus

Flame Speed Flame Colour Scene Light Fuel Bed Colour Volume Custom Dimmer +/Plus

Flame Speed – Spd Press the Spd button to cycle through the 3 flame speeds.
Flame Colour – Flam Press the Flam button to cycle through the 9 flame colours and off.
Down Light Colour – D Lt (Not available on LUX75XH) Press the D Lt button to cycle through the 9 down light colours and off
Scene Light Colour – Scn Scene lighting is an optional extra and this button will only operate if the Scene lights have been installed. Press the Scn button to cycle through the 9 scene light colours and off.
Fuel Bed Colours – Fuel Press the Fuel button to cycle through the 9 fuel bed colours and off. NOTE: Before attempting any operation with the remote, press and slide the battery door (on the bacNkOofTEre: mIf oytoeu) hoapveen taunrndeidnsoefrft atwll obuAtAoAnebaotfttehreielsig, chhtinegckeinlegmtheanttst,hyeou+ wanilldn-oet nbdesaobf ltehetobtaurtnteoryff the matlcahstinosnideeutshinegbthaettseerybcuottmonpsa. rTtmhiseinstf,ocrlyooseu tthoekbnoawttetrhyadt oyooru.r fire is still powered on. Custom Setting – Cust Using the 4 buttons detailed above, select your desired fire colours and then hold down the Cust button for 4 seconds. This will enable you to recall that setting each time you momentarily press the Cust button. To overwrite your setting, simply choose another set-up for your fire and hold down the Cust button for 4 seconds.
Dimming Buttons – Dim- and Dim+ Use these buttons to set the brightness level of your fire. (Fuel bed and flame effect will flash to signify max or min brightness.)
Flame Preset – PS Press the Flame Preset button to cycle through the 7 factory set preset lighting options.
Volume – Vol Press the Volume button to cycle through the volume settings from off to loudest, back to off.
11

Operation Continued
IMPORTANT NOTE: The fan will run for approximately 15 seconds after the heating function is turned off to remove any residual heat from the unit to protect the control components from any potential overheating. Do not press heater ON/OFF button again as this will turn the heat back on.
Remote control button combinations:
Switch beep off: Activate or deactivate the confirmation beep by pressing and holding Vol’ andDim-‘ for 3s and releasing.
Enter Wi-Fi pairing mode: Set fire to Wi-fi pairing mode by pressing and holding On/Off button for 10s.
Deactivate flicker effect: Activate or decativate the flicker effect for the fuel bed and downlight by pressing and holding Fuel’ andSpd’ for 3s and releasing.
Override flame brightness: Increase or decrease flame brightness without affecting other brightness, by pressing and holding Flam’ button, then press Dim-‘ or Dim+’. Override fuel bed brightness: Increase or decrease fuel bed brightness without affecting other brightness, by pressing and holdingFuel’ button, then press Dim-‘ orDim+’.
Override downlight brightness: (Not available on LUX75XH) Increase or decrease downlight brightness without affecting other brightness, by pressing and holding D Lt’ button, then pressDim-‘ or Dim+’. Override scene light brightness: Increase or decrease scene light brightness without affecting other brightness, by pressing and holdingScn’ button, then press Dim-‘ orDim+’.
Open Window Device function: To ensure minimum energy wastage, this appliance will turn off the heaters should an open door or window be detected. When the heater is in operation (H01 or H02) and once the ambient temperature drops 5°C within 10 minutes, the appliance heater will turn off automatically. Upon activation of the Open Window Device, the red indicator light will blink on for 0.5 seconds and then off for 0.5 seconds, repeating until the heaters have been restarted. Close the window/door or turn off any cooling items, push the heater control buttons on remote control to restart the heaters. To prevent nuisance activations of this device please ensure that there are no strong draughts in the vicinity of the fire or the furniture it is housed in.
Reconnect remote handset: If remote handset becomes unresponsive, re-pair connection between fire and remote handset, by pressing and holding Heat’ and Vol’ for 3s. The fuel bed will flash to confirm re-pairing is successful.
12

Product Dimensions
E
F

B

C

G

A

Dimensions

A

B

C

D

E

F

G

LUX75

750

581

737

226

335

83

82

LUX75XH 750

1250

1434

226

335

83

82

LUX100

1000

428

585

226

335

83

73

LUX125

1250

428

585

226

335

83

73

LUX150

1500

428

585

226

335

83

73

LUX175

1750

428

585

226

335

83

73

LUX200

2000

428

585

226

335

83

73

D
A minimum of 100mm is required between the top of the product and any hard surface.

Note: Dimensions stated are in millimetres unless otherwise stated and may be subject to a small tolerance.
Commissioning and Handover On completion of the installation: · Ensure that the operating instructions for the unit are left with the customer. · Ensure to advise the customer on the correct use of the appliance and how to isolate the unit
when required. · Advise the user what to do should smoke or fumes be emitted from the unit.

13

Information requirements for electric local space heaters

Model identifier(s): LUX75/LUX100/LUX125/LUX150/LUX175/LUX200

Item Heat output

Symbol Value Unit

Item

Unit

Type of heat input, for electric storage local space heaters only (select one)

LUX75/LUX75XH LUX100
Nominal heat output

Manual heat charge control, with

[no]

integrated thermostat

Manual heat charge control with room [no]

Pnom

1.5

kW

and/or outdoor temperature feedback

Minimum heat output (indicative)

Electronic heat charge control with

[no]

Pmin

0.75

kW

room and/or outdoor temperature feedback

Maximum continuous heat output
LUX125/LUX150 LUX175/LUX200
Nominal heat output

Pmax,c

1.5

kW

Fan assisted heat output

[no]

(select one)

Single stage heat output and no room

[no]

Pnom

2.0

kW

temperature control

Minimum heat output (indicative)

Two or more manual stages, no

Pmin

1.0

kW

room temperature control

[no]

Maximum continuous heat output

Pmax,c

2.0

kW

With mechanic thermostat room temperature control

[no]

With electronic room temperature

[no]

control

Electronic room temperature control

[no]

plus day timer

Auxiliary electricity consumption

Electronic room temperature control plus week timer

[yes]

At nominal heat output At minimum heat output In standby mode
Contact details

elmax

N/A

kW

Other control options (multiple selections possible)

Room temperature control, with

[no]

elmin

N/A

kW

presence detection

elSB

0.0039

kW

Room temperature control, with open window detection

[yes]

With distance control option

[yes]

With adaptive start control

[no]

With working time limitation

[yes]

With black bulb sensor

[no]

Capital Fireplaces Ltd, Units 12-17 Henlow Trading Est, Henlow, Bedfordshire SG16 6DS

14

Cleaning
before cleaning it. 1. Switch off and unplug from the power
supply before cleaning. 2. Using a soft, dry cloth, carefully clean
the exterior surface of the product. 3. Do not allow water or other liquids to
run into the interior of the product, as this is a hazard. 4. Lightly run a vacuum cleaner nozzle over the grilles along the control panel to remove any dust or dirt that may have accumulated inside or on the unit.
chemical cleaners or solvents as they
plastic components.
Thermal Safety Cut-Out
A thermal safety cut-out is incorporated in the heater to prevent damage due to overheating. This can happen if the heat outlet or the ventilation inlet is restricted in any way. The heater will switch on once the heater has cooled. If the cut-out continues to operate intermittently, the heater should be switched off and a service agent contacted.
Light Emitting Diode
Diodes) in place of traditional incandescent bulbs. These generate the same light levels as traditional bulbs, but use a fraction of the energy consumed.

Battery Replacement Remote Control
Battery information – see Fig. 35 1. Slide open the battery cover on
the back of the remote control 2. Install AAA batteries into the
remote control 3. Replace the battery cover

Flam D Lt PS Scn
Fuel

Heat

Vol

Cust

Dim

Dim

Fig.35

Dispose of batteries in the proper manner according to local regulations. Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all the batteries are not replaced at the same time, if
is made to charge a battery not intended to be recharged.

15

Troubleshooting
(IF IN DOUBT isolate the appliance and seek professional advice) Check main power on/off switch is on and indicator on control panel illuminates. If the light does not illuminate check the power to the fire from the wall and check the fuse in the plug and the circuit breakers in the distribution panel.
manufacture.
When the heater is switched on it cuts itself off.
removed, let the appliance cool down for 15 minutes and then reconnect the appliance to the mains and try the appliance again. If the issue persists, then seek the advice of your retailer. case it has been left on by mistake.
LUX fire sounds – During operation they will make quiet clicking sounds and will occur when
your heater fan and heating elements are switched on or off. 2. Flame Effect motor provides its drive via an internal gearbox that will emit a very faint gear noise. 3. Fan Heater – just like any fan heater there will be the sound of air being blown into the room. 4. Sampled Fire Sounds – The LUX75, 100, 125, 150, 175 and 200 feature a fire audio option. The volume of this sound can be adjusted using your handset or smart device. Excessive noise should be referred to your retailer. The thermostat reading on the App does not match the room temperature.
be necessary to set a higher target temperature in some instances. In some cases it may be more suitable to turn on the heating element(s) without setting a target temperature ­ see heater instructions. 16

Servicing and Maintenance
appliance. If there are issues that cannot be resolved with your appliance, then please contact your retailer.
and attach the brush accessory to your vacuum cleaner and gently vacuum the air intakes and outlets. (See image below) cleaners, steam or other household industrial products or cleaners.
With the fire switched off at the mains, gently vacuum the grille area as shown
If you have bought a new handset then you will need to pair it with your fire. This can be done with your fire turned on using the switch on the fire and holding down the new handset “Heat” and “Vol” buttons simultaneously for 5 seconds. Upon successful connection the fuel bed of your fire will flash 3 times.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
17

Solution Fires Warranty

All Solution Fires come with a standard 1 year parts warranty extendable to 2 years on registration.
dealer network will carry a 1 year nonextendable warranty. To activate your extended warranty, you must
co.uk within one month of the purchase date.
1 year non-extendable warranty. For full details of our warranty and to view the limitations and exclusions please visit our

control handsets is also excluded from the warranty. Should you experience problems with your Solution Fire, any claim must be submitted to the Solution Fire Retailer from where the Solution Fire was purchased. The Solution Fire warranty does not cover: 1) Damage resulting from installation and usage where the appliance has not been installed or used in accordance with the Solution Fire installation and operation instructions, or if the installation does not conform to local building,
2) Damage caused by unauthorised

For added peace of mind, why not purchase our Platinum Warranty Plan for a one off payment of £49.99 which gives you peace of mind for 5 years from date of purchase on all included parts and a 25% discount off non included parts and accessories. The platinum warranty is only available up to 60 days from date of purchase and only to

3. Damage or defects caused by the product being stored in a damp, unheated environment.
4. Consequential loss (to the extent permitted by the law) relating to other associated products that have not been supplied by Solution Fires.
5. Consequential loss (to the extent permitted by law) related to decorations, furnishings or other household assets.

an authorised dealer. Apply via our website

6. Removal and re-installation costs. 7) Accidental damage.

To ensure your Solution Fire continues to operate at its optimum level you must follow the care and maintenance advice in the user instructions.
Terms & Conditions This warranty is for domestic use, not transferable and is extended only to, and solely for, the
Fire. Please retain your dated sales receipt as a proof of purchase. During your warranty period, only genuine Solution Fire spare parts must be used in the servicing and maintenance of your Solution Fire, these spare parts can be ordered from
Solution Fire Retailer. Items considered as consumable such as glass, screens, bulbs, LED boards, ceramic logs, fuses and batteries which are either subject to normal wear and tear or parts that require replacement in connection with normal maintenance are not covered by the warranty. Loss or damage of any remote

Repaired or replaced components are covered only for the remainder of the original warranty period.
In the event of a product fault occurring during the warranty period, Solution Fires will send the appropriate component to rectify the fault, free of charge.
Nothing in the warranty shall make Solution Fires liable for any or special, incidental or consequential damages, injury to persons or property, or any other consequential loss beyond the consumer’s statutory rights. The liability on these issues is covered by Solution Fire Terms and Conditions of Sale.
Solution Fires total liability extends only to the purchase price paid for the goods, except where such a limitation is prohibited by statute. Solution Fires, in the event of a warranty claim, reserves the right to either replace the goods in question or to refund the purchase price of the goods. The Solution Fire warranty does not affect your statutory rights.

18

16

Exploded View

15

14

13

12

11 10 9 8 7 6

5

4 3

2

Replaceable Parts

No Description

LUX75

1 Remote Control Handset 22 03 249

2 Front Glass Plain

22 03 241

3 Side Glass Plain

22 03 243

4 Flame Screen

22 03 244

5 Decorative Side Panels

22 03 250

6 Fuel Bed

22 03 245

7 Flame Effect Lights

22 03 256

(Shorter LED strip)

8 Down Lights

22 03 265

9 Fuel Bed Lights

22 03 257

10 Flame Motor and Bush

22 03 236

11 Rotisserie

22 03 248

12 Heater and Fan Assembly 22 03 305

13 Main PCB Board

22 03 240

14 Control Board

22 03 306

15 Power Supply 5A-12V

22 03 057

16 Loud Speaker

22 03 144

LUX75XH 22 03 249 22 03 387 22 03 386 22 03 384
22 03 245 22 03 385
22 03 257 22 03 236 22 03 248 22 03 305 22 03 240 22 03 306 22 03 057 22 03 144

Part Number

LUX100

LUX125

LUX150

22 03 249 22 03 249 22 03 249

22 03 251 22 03 259 22 03 267

22 03 253 22 03 253 22 03 253

22 03 254 22 03 262 22 03 270

22 03 307 22 03 307 22 03 307

22 03 255 22 03 263 22 03 271

22 03 256 22 03 256 22 03 256

22 03 239

22 03 265 22 03 265 22 03 265

22 03 257 22 03 257 22 03 257

22 03 236 22 03 236 22 03 236

22 03 258 22 03 266 22 03 274

22 03 305 22 03 305 22 03 305

22 03 240 22 03 240 22 03 240

22 03 306 22 03 306 22 03 306

22 03 057 22 03 057 22 03 057

22 03 144 22 03 144 22 03 144

LUX175 22 03 249 22 03 275 22 03 253 22 03 278 22 03 307 22 03 279 22 03 256 22 03 239 22 03 265 22 03 257 22 03 236 22 03 282 22 03 305 22 03 240 22 03 306 22 03 057 22 03 144

1
LUX200 22 03 249 22 03 284 22 03 253 22 03 287 22 03 307 22 03 288 22 03 256
22 03 265 22 03 257 22 03 236 22 03 291 22 03 305 22 03 240 22 03 306 22 03 057 22 03 144

19

Variable Speed Motor Down Light LED Board Fuel Bed LED Board

Cut Out Heating Element
Blower Assembly

Wiring Diagram
20

LN

Power Supply

DCIN6 DCIN5 DCIN4 DCIN3 DCIN2 DCIN1 ABCD+

E086-003P-02
Main PCB

–++DW

Flame LED Board Scene Light

RF
NTC Sensor Receiver Board
Control Board

Manual ON/OFF Switch

App Instruction Manual

app and further explains the additional features of using a smart watch and Amazon Alexa with your Solution Fire.

From time-to-time improvements will be introduced and we would ask that

you periodically check the website

for updates to

these instructions.

Please note the handset that was supplied with your fire and the Solution Fires app work independently of each other. As such neither handset will be able to receive feedback from the other.

Contents
Pairing your Fire………………………………………………………………………………………………………………………. 23 Naming Fires…………………………………………………………………………………………………………………………… 29 Adding Fires……………………………………………………………………………………………………………………………. 30 Home Screen Explained ………………………………………………………………………………………………………….. 31 Accessing Features via Settings Menu Target Temperature ……………………………………………………………………………………………………………….. 33 Colour and Brightness …………………………………………………………………………………………………………….. 33 Sound…………………………………………………………………………………………………………………………………….. 34 Flame Speed………………………………………………………………………………………………………………………….. 34 Visual Presets………………………………………………………………………………………………………………………….. 34 7 Day Programmer …………………………………………………………………………………………………………………. 35 Account Settings ……………………………………………………………………………………………………………………. 36 Smart – Android Wear or Apple iOS …………………………………………………………………………………………. 37 Amazon/Alexa ……………………………………………………………………………………………………………………….. 38 FAQ Relating to the Solution Fires App ……………………………………………………………………………………. 40

In the following instructions the numbers adjacent to the screenshots correlate with the paragraph numbers. To Pair your Solution Fires App with your fire having already installed the fire and controlled it with the supplied handset, please refer to Section 13.

1. Download the Solution Fires App from the App Store, Google Play Store or from our website at

MANUAL CONTROL PANEL

FIRE ON/OFF BUTTON

HEATER MANUAL POWER ON/OFF SWITCH

INDICATOR
3. Ensure the manual power button is switched to “I” and the LED light is illuminated. This
4. Open the Solution Fires App. 5. Wait a moment for the Solution Fires App to initiate and then it will ask you to create an
account or log in to your existing account. If you have already registered and signed in to your account, your App will proceed to screen 6. It is essential to have an account in order to use the Solution Fires App. To create an account, only your name, a valid e-mail address and a password is required as well as your agreement to the Terms and Conditions. Our Terms and Conditions can also be viewed on our website at
Your fire will connect to the 2.4GHz Wi-Fi signal NOT the 5GHz signal – please ensure you select the 2.4GHz signal if your router identifies the two signals independent of each other. During this process you may be asked to allow the App to know your location. This is a requirement of your device. The App will only work if you allow this. The App does not use this information in any way. NOTE: The LED indicator illuminated red to indicate that power is on, but without Wi-fi connection. The LED is illuminated green to indicate that power on and the fire is connected to Wi-fi. The LED flashes to show that it is in Wi-Fi-pairing mode. The LED is off when the flame effect is running.

22

23

1

4

5

5

6. Once you have touched the “Submit” button having created an account or logged into your account, the Solution Fires App will start to search for your Solution LUX Fire.
7. Your Solution Fires App will find the fire you are trying to connect to and show it listed on the App screen. The fire will have a unique factory pre- set name similar to “SLELUX#####”. If your App does not find your fire then please refer to step 13 below.

6

7

24

25

8. 9.
and you will be asked for the password for that network. If this is not the network you wish to connect to, then you must type in the name of your desired network manually and provide the password in the normal way. Take care to type accurately.

8

9

10. You will now be asked for the password to your Wi-Fi network. Touch the eye icon to review the password typed in.
11. Once connected you can turn on your fire and start to enjoy the wide array of features provided to you via the Solution Fire App. If your fire has not connected, please refer to section 13.
12. The App should now show the home screen. If your home screen does not update with the room temperature within two minutes and two dashes remain beneath the words “Room Temperature” it is likely that you have entered the incorrect password to your Wi-Fi. If this is the case, you will need to restart the process at section 13.
13.

steps. Make sure the Manual Power ON/OFF switch is in the “I” position. Turn on the fire using the fire ON/OFF button. Then press and hold the fire ON/OFF button or the ON/OFF button on the remote handset for 10 seconds. This prepares your fire for the pairing process. The LED will start flashing.
MANUAL CONTROL PANEL

FIRE ON/OFF BUTTON

HEATER

MANUAL POWER ON/OFF SWITCH

INDICATOR
14. Open the Solution Fires Application and follow the instructions from point 5. When you arrive at

enjoy the many control features.
NOTE: The LED indicator is illuminated red to indicate that power is on, but without Wi-fi connection. The LED is illuminated green to indicate that power on and the fire is connected to Wi-fi. The LED flashes to show that it is in Wi-Fi-pairing mode.

26

27

10

11

11

12

Naming Fires
15. You may want to change the name
15
settings button at the top of the Home screen. 16. 17. here you can rename them all one by-one. Touch the blue “pad and
whose name you would like to change. 18. Type new name and then submit.

16

17

28

29

Adding Fires

19. this, touch the settings
20.

button at the top of the Home screen.

19

20

Home Screen Explained
22-27

21. of these instructions.
30

section

22. To the left are the Home button and the Settings button. To the right are the 7-day timer button and the Instructions button. a. The Home button will bring you back to this screen whenever you touch it. b. The Settings button takes you to the settings menu from where you can select one of the
c. The 7-day programmer button will be bright if you have set the 7-day timer function and is a short cut button to the screen where you are able to set the 7-day timer. d. The button takes you to the instructions for using your App. 23.
24. This may take up to one minute.
31

25. Manual heater buttons. a. Press for 1kW of heat or for 2kW of heat. b. please see section 28 of these instructions on setting Target Temperature. By activating the heater buttons from the Home screen, you override the Target Temperature feature if it has been set. c. If you have set the 7-day programmer, this will override both the manual heater buttons and the target temperature function.
26. open by analysing if a sudden drop in room temperature occurs. If this does happen then your fire will automatically stop heating the room, the indicator light on the manual control panel will blink rapidly and a pop-up warning appears on your application. Follow the instructions on this screen to reset your heater.
26

Accessing Features via Settings Menu
28
(See previous page)
Target Temperature
28. visit this screen, you will see two dashes instead of numbers. This will change to your setting once you adjust the slider control. Set your desired target temperature for your room.
29. You can select a target temperature between 15°C (59°F) and 30°C (86°F). Once you have set

warm your room to that temperature and maintain it around that temperature. Set the temperature by sliding the button along the line or by touching the + or ­ symbols. Save your target temperature as your Custom setting – this would then be activated when you select your “Custom Preset” from the “Visual Presets” screen ­ please see section 33.

NOTE – If you set a target temperature when using

30

the 7-day programmer (section 34), that will not be

control of your 7-day timer settings.

Colour and Brightness
30. Select your own colour and brightness settings

27. a. Lights ­ touching this button takes you to the screen where you can control the colour and brightness (colour only for downlight) of the individual lighting elements of the fire. Please refer to section 30 of these instructions. b. Sound – your fire has a factory pre-set of no sound. This can be adjusted from this button see section 32 of the instructions.
c. Pre-sets – Choose from 7 different factory set fire settings. On the “Visual Presets” screen
there is an eighth button which when touched allows you to change your fire to a set-up
that you have chosen. Please refer to sections 29-31 of the instructions for more information.

navigate directly to this screen from the Home screen.
31. like to adjust ­ in this case the fuel bed has been selected. Adjust the brightness using the slider or the + and ­ symbols. Select one of the nine different colours. The “Scene Light” button will be only available if you have added the optional
settings as your “custom preset” which would then be activated from the “Visual Presets” screen please see section 33.

32

33

32
Sound
32. Mute or adjust the volume of the sound of

35
7 Day Programmer
35. See detailed explanation on page 35.

33
Flame Speed
33. Adjust the Speed of the flame effect.

34
Visual
34. Select any one of the seven factory set lighting schemes or your own Custom effect.

7 Day Programmer (See image on previous page)
35. Your app will automatically take the day and time from your phone or tablet. If you are setting
Now select “7 day programme” from the settings menu and proceed as follows: a. Turn on the “Use 7-day programme” b. heating together. c. Select the days you wish to control. There are “bulk” options of “Weekdays”, “Weekends” or “Everyday” or you may wish to set each day separately by simply selecting the initial letter of the day you wish to set. d. touching the “time on” and “time off” boxes in turn. e.
f. same process for “Period 2”.
programme. 36. You will notice that any screen you navigate to once you have set the 7-day programmer will
have the illuminated calendar icon at the top right-hand side of each screen. This is a quick reference for you to check if your fire has the 7-day programme set or not. You can touch the calendar icon to navigate quickly to the 7-day timer screen. 37. To cancel the 7-day programmer, turn off the “Use 7-day programme” switch and press the
7-day programmer back on at some future stage. 38. To review your settings, return to the 7-day programme screen and touch each day in turn
and review the settings for each day one-at-a-time. You may review one day’s setting at a time
this screen.
Flicker Effect (See image on previous page)
39. The flicker effect for the fuel bed and downlight can be deactivated using the Flicker on/off function.

34

35

Account Settings
40. The Account Settings screen is reached by selecting that button from the Settings menu.
40 John Smith John.Smith@example.co.uk

Smart Watch
Android Wear or Apple iOS
42. Having paired your smart watch to the device on which you have already installed the
43. Please do not forget that your smart device and watch need to be in the vicinity of each other for the smart watch to function correctly.
44. In the case of the Android Wear Watch you will need to add the app to it by accessing the Google Play Store and adding the Solution Fires app from the phone.
45. In the case of the Apple iOS watches (Version 1 is not supported) the app appears automatically on the watch app screen.
46. Firstly, open the App on your watch, then the functions that are controllable from your smart watch are: a. ON/OFF b. Heat – 1kW, 2kW, OFF (0.75kW, 1.5kW, OFF for LUX75, LUX75XH and LUX100) c. Presets 1-7 (watch includes the custom preset if it has been programmed on your smart phone or tablet)

41. The features here assume that you are logged in to your account and are as follows: You may change the name, email address and password of your account at any time. a. Tap the “Change name” button to change first and second names.
b. Tap “Change email address” to change the registered email address. The email address here is the one to which e-mails to help you with forgotten passwords will be sent.
c. Tap “Change password” button to change your password. The level of security is entirely up to you.
d. To avoid others using your app to control your fire, you can “Sign out” of your account at any time.
e. You may decide to delete the account that you have set up. The main reason for this would be moving home.
f. Here you may refresh your memory regarding the Terms and Conditions and Privacy Policy by touching the relevant buttons.
g. “Cancel” takes you back to the Settings screen.

36

37

Amazon Alexa
47. Download the Solution Fires Skill onto your smart device you use to control Alexa. In order to use your Amazon Alexa to control your Solution Fire it is important that you link your Solution Fire with the Amazon Alexa app on your smart device.
48. There are two ways in which to ask Alexa to control your Solution Fire, Alexa will control only
a. “Alexa, open Solution Fires” or “Alexa, Solution Fires” b. “Alexa, [ask/tell] Solution Fires to…………………………………………………………………………………… ” 49. When you open Solution Fires, using option 46a, wait for Alexa to say: “Hi, how can I help?” within one or two seconds make your request from the list below. Alexa will confirm your request and then ask if she can help with anything else, at which point you can make further requests from the list below. 50. When you use the option 48b, add the request from the list below. You can make further requests from the request list after Alexa has confirmed your last request has been followed and has asked you: “Can I help with anything else?” 51. Some people have changed the name from “Alexa”, in these cases please use the name you have chosen instead of “Alexa” in the examples above. 52. Request list; 1. “turn power [on/off]” 2. “turn [on/off]” 3. “turn [fire name] [on/off]” 4. “turn heater [on/off]” 5. “set heat level to medium” 6. “turn sound [on/off]” 7. “[mute/unmute] sound” 8. “turn volume [up/down]” 9. “change fire to [pre- set name]” 10. “set pre-set [pre-set name]” 11. “pre-set [pre-set name]” 12. “[pre-set name] effect” 13. “change colour to [pre-set name]” 14. “change pre- set to [pre-set name]” 15. “turn fire to [pre-set name]”
38

52. Request list continued; Pre-set names are as follows, with alternatives to try in brackets; 1. Blaze (orange, one, fire, flame, hot, default) 2. Inferno (very orange, two, ignite, flare) 3. Solar (yellow, three, sun, sol) 4. Magma (red, four, very red, lava, volcano) 5. Lunar (pink, purple, five, space, star, stars, orbit) 6. Ice (frozen, freeze, six, glacier, chill, cold) 7. Spirit (ghost, seven, ethereal, spectre) 8. Custom ­ once you have set it. Its default is “Blaze” (my setting, eight)
53. Please refer to www.solutionfires.co.uk periodically to see if any new commands have been added.
39

FAQ relating to the Solution Fires App

1. Can I review the instructions from my app? Yes, simply touch the information button at the top of your app screen and the instructions will then appear.

2. How do I know that my fire is ready to pair with my Wi-Fi network?
When you turn on your fire for the very first time, your fire will be broadcasting its own signal for you to connect to. If you are not sure, then use your phone or tablet to search for networks and if you see one called something similar to “SLE_LUX_3df4a”, then you know that your fire is ready to connect. Do not connect directly to that network on your phone other than through the Solution Fire app. Now follow the instructions to connect the fire.

3. What should I do if my fire is not ready to pair with my Wi-Fi network?

Ensure the manual power button is switched to on (I), using the fire ON/OFF button indicated below,

turn on the fire. Now hold the ON/OFF button on the fire or remote handset, for 10 seconds, to put

the fire in its “broadcast mode”, ready for you to connect. The LED indicator will start flashing (red if

not already connected to a network, green if currently connected to a network. Now follow the

instructions on page 25 and 26.

MANUAL CONTROL PANEL

FIRE ON/OFF BUTTON

HEATER

MANUAL POWER ON/OFF SWITCH

INDICATOR
4. Must I allow the app to know my location for the app to work? Yes, this is a requirement of the platforms the apps are built on and the app will not work unless you permit this. This information is not stored or used in any way by Solution Fires. Please refer to the Privacy Policy and Terms and Conditions for further information. You must enable notifications whilst using the app. 5. Do I need an account for my app to work? Yes, it takes a few moments to set up an account with very little information required to set one up. Please refer to the Privacy Policy and Terms and Conditions for further information. 6. Must I agree to the Terms and conditions and Privacy Policy to be able to use the app? Yes, there is a tick box to confirm your acceptance when you set up an. Please refer to the Privacy Policy and Terms and Conditions for further information. 7. Do I have to connect the fire to the 2.4GHz Wi-Fi signal in my home? Yes, in common with most home appliances, the Solutions Fires range will connect only to the 2.4GHz signal from your Wi-Fi router. This is only important if your router has the 2.4GHz signal separated from the 5.0GHz signal. 8. Should my smart phone/tablet software be up-to-date? Yes, please ensure you update your device software regularly.
40

9. My phone/tablet does not show the correct home Wi-Fi name for me to connect to, how do I resolve this? This can occur if the signal of the desired network is weaker than another in your vicinity. In some cases your device may try to connect to the fire network for its internet access. When you have reached the stage in the set-up process described in the instructions where your app has identified the local Wi-Fi network to connect to, and it is not showing the correct one, simply tap the box where the name is listed and type in the correct one. TIP ­ it is worth using your phone/ tablet to review the available networks before reaching this stage and noting down the name of your desired network – exactly the characters and spaces as it is shown, because any mistakes in typing it in will prevent your fire from connecting to your network. Please take care to type your password accurately.
10. My phone/tablet keeps trying to connect to the fire to access the internet, what should I do? This can happen, depending on the setting of your device. Go to your settings and select the “SLELUX#####” network and “forget” it by using one of the menus provided by your device. Once you have done this, you may have to completely reboot your device and restart the pairing process, following the instructions. Please take care to type your password accurately.
11. Can I view what I have typed in as my password? Yes, touch the eye icon in the box where you are typing your password to review the password typed in. The app does not know if you have typed the password correctly or not and so will proceed to its next step of the connection until you find that you are unable to proceed any further.
12. Can I change my Solution Fires app account password? Yes, navigate to the settings page of your app , select “Account settings”, tap the “Change password” button and follow the instructions.
13. What should I do if I forget my Solution Fires app account password? When you try to log in to your account there is an underlined “Forgot password” line at the bottom of the screen. By touching this you will be sent an e-mail to the e-mail address you previously registered and from that e-mail you will be able to reset your password. If a new password request has been inputted more than once, only respond to the first link that is sent to you from Solution to rectify. The link may take a few minutes to come through.
14. Is it normal for the red indicator light to blink? Yes, this will happen if your Open Window Device has been detected. To reset this, ensure that the cause of the sudden drop in temperature has been resolved and then turn the heater on.
15. I have previously been able to control my fire using my app, why am I unable to now? It is probable that your Wi-Fi signal is weak and has been lost or that your internet access via your router has been interrupted. To stop this it may be necessary to add a booster or improve your internet connection/broadband. You can try rebooting your router. It is also possible that you are using a different account to the one that set up the fire and the account you are using has not been set up. To set up the fire using another account, please follow the set-up procedure in the instructions.
41

16. Can a busy network affect the performance of my app? For best results when controlling your fire your broadband connection should be stable and have sufficient bandwidth to allow speedy connection to the internet. It is possible that the speed of response is affected by heavy use of your Wi-Fi and local heavy `traffic’ at peak times of the day. It is also understood that weather can affect connection speeds.
17. What is causing the fire to take more than one or two seconds to follow the instructions of the app? When using the app to set various features, occasionally there is a lag between the time you press the screen button and the signal reaching your fire. Further presses of other buttons will normally operate in the sequence you press them. However, if there are too many button presses in a short period of time the fire can miss an instruction. Simply wait a few seconds and try again if your fire is not responding to the setting you require. The lag can be caused by a number of issues including local network speed, age, version and some settings of devices in the control loop (phone/watch/ tablet/operating system/router), Wi-Fi signal strength and local internet stability. Please check these. Often a reboot of your router and/or fire can help.
18. Why is my room temperature not updating on my app home screen? If your home screen does not update with the room temperature within two minutes and two dashes remain beneath the words “Room Temperature” it is likely that you have entered the incorrect password to your Wi-Fi when setting up your fire. If this is the case, you will need to restart the process.
19. Is it possible to add another Solutions Fire to my app? Yes, navigate to the settings page of your app , select “Adding & naming fires”, tap the “Add a new fire” button and follow the instructions.
20. Can I rename my fire? Yes, navigate to the settings page of your app , select “Adding & naming fires”, tap the blue “pen and pad” icon adjacent the fire whose name you would like to change and follow the instructions.
21. Can I set a 7-day timer programme for my fire? Yes, navigate to the settings page of your app , select “7 day programme” and follow the instructions. There is a short cut to this screen ­ at the top of any screen is a calendar button ­ touch that and you will be taken to the programme screen. Please remember to turn on the switch that says “Use 7-day programme” and “confirm” your settings at the bottom of the programming screen. Once you have done this, you will notice after a minute or two that the calendar button at the top of your app screen will highlight.
22. Is it possible to store my favourite settings so I can recall them at a later date? Yes, once you have set your desired look and sound, press the “Save as custom” button at the bottom of any of the “Colour & Brightness”, “Sound” or “Target Temperature” screens. You will then be able to revert to those settings from the “Pre-sets” screen by touching the “Custom” button.
23. Can I set independently the colours and brightness of the different lit elements of my fire? Yes, navigate to the “Colour & Brightness” screen from the “Home” screen by touching the “Lights” button. Here you can adjust the colours by touching the relevant colour selection button, of the flame, fuel bed, down lights and scene lights (if fitted). Here you can also adjust the brightness of the flame, fuel bed and scene lights (if fitted) by using the slider control on the screen or by touching the “+” or “-” buttons at the end of the slider. Once set, you can save your bespoke fire settings as your custom setting ­ please see instructions for more information.
42

24. Can I adjust the volume of the fire sound coming from my fire? Yes, simply navigate to the “Sound” screen from the “Home” screen by touching the “Sound” button. Here you can mute the crackling sound of your fire or, when it is not muted, adjust the volume of the sound by using the slider control on the screen or by touching the “+” or “-” buttons at the end of the slider. 25. Are there some pre-set fire settings for me to review? Yes, these can be reviewed by touching the “Pre-sets” button on the “Home” screen and selecting one of the buttons on that screen. 26. Can my smart watch control my fire? Yes, once you have paired you fire with the phone or tablet that is connected to your smart watch you can select the app on your smart watch as per the instructions for your smart watch. Using your smart watch you can control the fire on/off, mute the sounds, select pre-sets and turn on and off the heater. 27. What should I do if my smart watch stops controlling my fire? Your watch may sometimes cease to control your fire because the signal between your watch and phone has been interrupted. This can be due to the distance between your watch and phone. It can also be due to your phone optimising its battery usage. Your phone is likely to be optimising its battery usage when its charge has reached about 20% or less. When optimising, the phone will divert battery power to other, more essential functions. You may be able to adjust your optimisation settings on your phone. Alternatively a solution is to charge your phone and double check the connection between your phone and watch. 28. Can I control my fire using Alexa? Yes, open the Amazon Alexa app on your device and search for the Solution Fires skill and link your account to the Solution Fires account you have set up in your app, then try some of the commands listed in the instructions. For example: “Alexa, [ask/tell] Solution Fires to change colour to pink” 29. Will the app be updated occasionally? From time-to-time improvements will be introduced ­ please refer to the www.solutionfires.co.uk website for updates to these instructions. 30. Can I use the remote control handset at the same time as the app? Please note that the remote control handset supplied with your fire and the app work independently of each other. As such neither handset will be able to receive feedback from the other, therefore whichever handset is used your last settings in that handset will be sent to the fire. This can mean after using your app, when you ask the heater to come on with the remote control your fire colours may change to the last ones set in the remote control if they are different from those colour set by the app last time.
43

www.solutionfires.co.uk info@solutionfires.co.uk
CAPITAL FIREPLACES LTD, Unit 12-17 Henlow Trading Estate, Henlow Camp, Bedfordshire, SG16 6DS. UK.

References

• Homepage - Solution Fires

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>