GYMAX GYM06624 1500 Watt Electric Fireplace User Manual

GYMAX GYM06624 1500 Watt Electric Fireplace

Contact Us!
Do NOT return this item. Contact our friendly customer service department for help first.

Before You Start

• Please read all instructions carefully.
• Retain instructions for future reference.
• Separate and count all parts and hardware.
• Read through each step carefully and follow the proper order.
• We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
• Always place the product on a flat, steady and stable surface.
• Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.

Safety Information

IMPORTANT SAFETY INFORMATION
PLEASE READ ALL OF THE INFORMATION IN THIS OPERATING MANUAL, INCLUDING ALL SAFETY, OPERATING, AND MAINTENANCE INFORMATION. TO AV0D THE POTENTIAL RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, USERS SHOULD FOLLOW THE DIRECTIONS AND WARNINGS IN THIS MANUAL.

1. Read all instructions before using this heater.
2. Do not use this heater outdoors.
3. This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
4. Do not run the power cord under carpeting. Do not cover the power cord with throw rugs, runners, or the like. Arrange the power cord away from traffic areas and where it will not be tripped over.
5. To disconnect the heater, turn the controls to off, then remove the plug from the outlet.
6. Connect to properly grounded outlets only. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
7. To prevent a possible fire, do not block firebox air intakes or the exhaust in any manner. Do not operate the firebox on soft surfaces, like a bed, where openings may become blocked.
8. There is a thermostat limiter inside the heater. When the inner temperature overheats or abnormal heating OcCurs, the thermostat protective device cuts off the power supply to avoid fireplace damage or the risk of fire.
9. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons. SAVE THESE INSTRUCTIONS

WARNING: There are no user-serviceable parts inside the fireplace/heater. If the unit appears to malfunction, tum the unit off and unplug the unit from the wall immediately, and contact Customer Service
WARNING: This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. f provided, use handles when moving this heater. Keep combustible material, Such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft. (0.9 meters) from the front of the heater and keep them away from the sides and rear.
WARNING: Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
WARNING: Always unplug the heater when not in use.
WARNING: Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
WARNING: Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may cause an electric shock or fire, or damage the heater.
WARNING: A heater has hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.
CAUTION: While the heater is in use, the top center of the fireplace can get hot to the touch, and may cause serious injury or burns. Always supervise small children arouna the fireplace/neater. Do not place any action or decorations over the heater outlet of the fireplace, or otherwise obstruct the heater outlet of the fireplace, as this may cause a fire and serious injury may result.

GROUNDING INSTRUCTIONS

DANGER: Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by qualified electrician.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This heater is for use on 120-volt circuits and has a grounded plug. An adapter is available from your local electronics store or online supplier for connecting three-blade grounding type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

Warranty

We are confident that you will be delighted with this purchase. Should this product be defective In workmanship or materials, or fail under normal use, we will repair or replace it for a period of up to one (1) year from date of purchase. This warranty gives you specific rights and you may also have other rights which vary from state to state.

Pre-installation

ELECTRICAL SPECIFICATIONS

• Voltage: 120 VAC, 60 Hz
• Watts: 1400 Watts

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

CAUTION: This insert has front panel made of GLASS! ALWAYS use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.

Assembly

Attaching the metal trims

• Fasten the top trim (X) to the top of the fireplace insert (W) with two screws (18). Make sure that the right-angle side points towards the front of the
• Align and attach two side trims (Y) to both sides of the fireplace insert (W) respectively with the right angle side facing the front of the unit, using two screws (18) per

Installing the fireplace insert

Carefully set the fireplace insert (W) into the back of the mantel and center it in the opening. Use care not to scratch the w0od. Check the alignment, and then attach the fireplace insert (W) to the mantel by inserting the screws (18) through the drilled holes on the trims (X and Y) and securely screw into place using a Phillips screwdriver.
NOTE: DO NOT attemot to install the insert from the front of the mantel- it will not fit.

Operation

ldentifying the control panel

• The control panel is located on the top right corner of the fireplace/heater unit.
• The control panel contains the main power (1), flames control (2) and heater control (3).

Using the main power button

• Press the power button (1) to turn the fireplace/heater unit on and off. Press the power button (1) once to turn the unit on. Press again to turn the unit off.

Using the flame control

• Press the flame button (2) to set the flames for different levels of flame height. You can control the flame height as the table below:
  Button Press| Flame Level| Fireplace Appearance
  ---|---|---
  1st press| Medium| Flames Medium, Logs Glow Medium
  2nd press| Low| Flames Low, Logs Glow Low
  3rd press| All Off| Flames Off, Logs Off
  4th press| High| Flames Highest, Logs Glow Highest
• When the heater function turns on, the flame level will cycle through the 3 different level settings continuously.
  Button Press| Flame Level| Fireplace Appearance
  ---|---|---
  1st press| Medium| Flames Medium, Logs Glow Medium
  2nd press| Low| Flames Low, Logs Glow Low
  3rd press| High| Flames Highest, Logs Glow Highest
• If the flame is off when the unit is turned off by the main power button, the flames will come on in the highest mode when you turn the heater on.

Using the heater control

• Press the heater button (3) to turn on or off the heat There is no speed setting for the heater blower. If you turn off the heater by the main power button (1), the unit will hold the setting in the memory. When the power is turned back on, the heater will turn on at the same setting.
• When the flame function turns on, press the heater button (3) once to turn the heater Press again to turn the heater off.
• When the flame function turns off, the flames will come on in highest mode when the unit is turned on heater button (3).

Using the Remote Control

Installing the battery
The battery is supplied with the remote control. The first thing to do with the remote control is to remove the plastic sheet insulating the battery. For replacement battery, use lithium-based CR2025 battery. Please follow the sequence below to replace the battery.

• Take out the battery bracket.
• Insert the battery with the button side into the battery bracket, making sure the battery is firmly
• Press the battery bracket into the remote control, making sure it snaps into position.
• Turn the remote over and aim it towards the fireplace/heater unit.
• Press the power button on the upper portion, and see if the flames on the fireplace/heater turn on or
• If nothing appears to happen, check to make sure the battery is installed correctly, and try

WARNING: Do not ingest batteries.

1. Non-rechargeable batteries are not to be
2. Batteries are to be inserted with the correct
3. Exhausted batteries are to be removed from the
4. Always purchase the correct size and grade of battery most suitable for the intended use.
5. Replace all batteries of a set at the same
6. Clean the battery contacts and also those of the device prior to the battery
7. Remove batteries from equipment when not used for an extended period of time.

NOTE: Battery disposal Please always dispose of batteries at a suitable recycling point.

Using the remote control
The operation of the remote control buttons works the same as the buttons on the front panel of the fireplace/heater. Review the Operation section for more information on the functionality of these buttons.

Care and Maintenance

WARNING: Always disconnect from the power supply before cleaning the heater. First, turn off the main power. Then remove the electrical plug from the wall Outlet.
WARNING: Do not use this fireplace insert if any part of it has been under water. Immediately call a qualified service technician to inspect the firebox and replace any part of the electrical system which has been under water.
The blower motor and flame motor are pre-lubricated for a durable using time and need no further lubrication or maintenance. To remove any accumulation of dust or debris, the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan heater.

• Use a soft, clean cloth that will not scratch the surface when
• Use a clean soft cloth dampened with warm water to clean the fireplace DO NOT use household or abrasive cleaners, as these products may damage the surface.
• When cleaning the glass viewing screen use a non-abrasive damp cloth with liquid cleaner or soft soap if necessary; DO NOT use cleaning powders or any other substance with abrasives since these substances will scratch
• Under no circumstances should this product be operated with a broken or chipped glass
• Do not strike or slam the
• In the event that your appliance is stained or otherwise damaged during use, we recommend that you call a professional to
• When not in use please unplug the cord from the outlet to prevent any damage or accidents.

Troubleshooting

standard 120 V outlet.

□    Press the power button on the control panel.

The unit is on, but there is no flame effect.| □ Open the back panels to check if the flame spindle has fallen off from the spindle motor.
There is a visible flame effect, but the heater does not continue to blow warm air after repeatedly turning on the heater.| □ Turn on/off the heater button several times to make sure it is in the “ON” position.
The heater does not work, but the power and heater switches are in the “ON” position.| □ Turn all switches to the “OFF” position and unplug the unit from the wall outlet for 5 minutes. After 5 minutes plug the unit back into the wall outlet, and operate as normal. Make sure that no objects are blocking the air vents on the top and on the front of your fireplace .
Remote control is not working.| □    Change the remote battery.

□    Operate remote transmitter at a slow measured pace.

Press the remote control buttons with an even motion and gentle pressure.

□    Repeatedly pressing buttons in rapid succession may cause the transmitter to malfunction.

□    Stand closer to your fireplace.

□    Remove objects that may block your remote control’s ability to communicate with your fireplace.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>