ARMYTEK VIKING PRO Tactical Flashlight User Manual

VIKING PRO Tactical Flashlight
User Manual

Thank you for choosing the products of Armytek.
Please read this manual carefully before using the flashlight.

Specifications

Modes, light output and runtimes (measured with 18650 Li-Ion 3500 mAh battery until the light output drops to 10% of the initial value)| Turbo| 2200 lm/1 h 33 min (940 Im after 3 min)
Main3| 4001m/5 h 13 min
Main2| 150 Im/12 h 20 min
Mainl| 56 Im/32 h
Strobe2| 15 Hz/2200 Im/3 h (940 Im after 3 min)
Strobel| 15 Hz/150 Im/23 h
Power source| 1×18650 Li-Ion
Length/Body diameter/Head diameter| 160 mm/25.4 mm/41 mm
Weight without/with battery| 135/185 g
Dust, water and impact resistance| IP68. Submersion at 25 m up to 5 h. Fallings from 25 m

▶ Light output for flashlights with Warm light is about 7% less, and beam distance is about 3% less. All the above specifications are test results based on ANSI/NEMA FL1-2009 Standard.
The tests are performed using the battery included in the set. The data may vary due to environment, heat dissipation, and other factors.

• Special precisely calculated reflectors for powerful wide LED and tempered glass with anti-reflective coating create a large central spot and wide side spill at 2200 lumens brightness. The spill diameter is 20 meters at 100 meters distance
• Powerful electronics provide constant brightness even at a temperature of -40 °C and not fully charged battery
• Two types of operation: hunting and tactical. Tactical operation for quick access to maximum brightness mode and Strobe mode
• Withstands any recoil due to improved  springs and installation of the driver inside a reinforced capsule filled with protective compound
• The standard 1-inch body is compatible with any accessories, including the original magnetic remote switch and a magnetic mount for quick one-motion attachment and removal
•  The two-phase electronic button retained two levels of pressing similar to a mechanical switch but became noiseless and 20 times more durable
• The non-flat button allows you to  easily switch the flashlight with a palm
• Innovative technology allows using any 18650 Li-Ion batteries with 10A discharge current and provides full protection against short circuits even in case of contact between the magnetic connector and metal objects
• Solid-body made from aircraft-grade aluminum, special matt anti-abrasive finish without rough knurling
• Steel striking bezel with matte non-reflective black titanium coating, which prevents location disclosure, is used for additional protection of the optical system in the event  of a fall and as a shock-crushing tool
• Active real-time temperature control to prevent overheating above +58 °C and warning indication of low battery level
• Total protection from water, dirt, and dust in accordance with IP68  standard — flashlight continues to work even at 25 meters depth up to 5 hours. Withstands fallings from the 10th floor
• Robust and water-resistant magnetic connector

Set description

Flashlight, 18650 Li-Ion 3500 mAh battery, magnetic USB charger, clip, lanyard, holster, silicone grip, 2 spare O-rings, user manual.
The producer reserves the right to change the package at his own discretion without modifying this manual. Specifications are subject to change without notice.

Initial Service

TO SET/REPLACE THE BATTERY

1. Unscrew the tail cap.
2. Place the battery with the positive contact (+) facing the head of the flashlight.
3. Adjust the tail cap and tighten it as far as it can go.
   The flashlight is ready for operation.

HOW TO CONNECT THE MAGNETIC CHARGER

Tighten the head of the flashlight as far as it can go and adjust the magnetic charger to the tail cap.
CHARGER COLOR INDICATION
Charger not plugged in:

• Green — device is in waiting mode.

Charger plugged in:

• Green blinking — evaluation of battery voltage.
• Red blinking — clean the external and internal contacts of the tail cap, as well as the contact areas of the charger.
• Orange blinking — USB power source voltage is too low for the correct continuation of charging or bad contact between charger and battery. Clean the tail cap and the threads of the flashlight parts, and use a different power source.

Operation

Before use: Tighten the tail cap as far as it can go.
IN ANY MODE

Permanent on. The first full click of the button turns the flashlight on.
The second full click turns it off.
Momentary on. Switched on by half-pressing the button (no click) and active till the button is released.
To switch between types of operation unscrew and tighten up the head of the flashlight at least 10 times (during rotation the modes will be changing). The pause between the moves must be less than 1 sec.
The flashlight blinks once, confirming the action.
HUNTING TYPE (BY DEFAULT)
Turbo. Before switching on the flashlight in Turbo mode, tighten the head of the flashlight if it is unscrewed.
Additional modes. Before switching on the flashlight in Additional mode, unscrew the head to 1/8 if it is tightened. Full click switches on the last used Additional mode.
Cycling through Additional modes. To switch the mode turn the flashlight off and on (by full click or half-pressing). The flashlight must not be turned off for more than 2 sec. The modes switch cyclically:
Main1 – Main2 – Main3 – Strobe2 (if enabled).
Add/Remove Strobe2 in Additional modes. Switch on the flashlight by half- pressing at least 20 times. The flashlight must not be turned on for more than 1 sec. The last switch must be a full click. The flashlight blinks once, confirming the action.
The remote switch must be used in Turbo mode.
TACTICAL TYPE
Constant light. Before switching on the flashlight in Constant light mode, tighten the head if it is unscrewed.
Changing Constant light modes. The head is tightened: unscrew it to 1/8 and tighten again in 1 sec. Turbo and Main2 will switch cyclically.
Strobe. Before switching on the flashlight in Strobe mode, unscrew the head to 1/8 if it is tightened.
Changing Strobe modes. The head is unscrewed: tighten it and unscrew it to 1/8 again. Strobe1 and Strobe2 will switch cyclically.
The remote switch can be used in ANY mode.
Auto memorizing. After switching off the last used mode is memorized for quick access at the next switching on.
Safe high brightness modes. Turbo mode gives maximum brightness until the temperature of the flashlight and discharges current of the battery don’t exceed critical values.
Digital Light Stabilization & Safe Soft-Start System allows to increase runtime, get a longer lifetime of rechargeable battery, and protects it from over-discharge or overheating. Active temperature control. When the temperature of the flashlight becomes close to +58 °С, brightness decreases to a safe value, allowing the flashlight to avoid overheating for a long period of time. In conditions of good air-cooling, the flashlight delivers light without stepping down.
Low battery level. If the brightness of the mode is approximately <25% from the nominal value, the LED will flash 2 times (after 30 sec from switching on). If you are not sure whether it flashed or not, switch the flashlight off and on: if the battery is low, flashes will repeat.
Lock-out function. Unscrew the tail cap to 1/4 for protection from accidental switching on.
Warnings
For stable operation of the flashlight in Turbo and Strobe2 modes, we recommend branded 18650 Li-Ion batteries without PCB (unprotected) or with PCB which guarantees a 10A discharge current.
The flashlight can get hot in Turbo and Strobe2 modes quickly and discharge the battery with a high current. Don’t leave it without your attention as very bright light might heat objects and cause a fire. It is forbidden to charge the battery inside the flashlight when the ambient temperature is below 0 °C.

1. Always follow the instructions from this manual and recommendations on battery usage.
2. Apply only the recommended power sources.
3. Do not reverse battery polarity.
4. Do not modify or recast the flashlight and its components as it will deprive you of the warranty.
5. Do not allow water or any other liquid to leak into the flashlight.
6. Do not aim a switched-on flashlight at people’s or animals’ eyes — it can cause temporary blindness.
7. Do not allow children to use the flashlight without your assistance.

The producer will not be liable for any harm done to the user if it was caused by improper use of the product.

Care and Storage

It is recommended to clean the threads and O-rings of dirt and old grease once or twice per year. Remember that reliable protection from water and dust cannot be provided by worn-out sealing. The fouling as well as lack of lubricant causes fast wear-out of threads and sealing rings.
To clean the threads do the following:

1. Unscrew the tail cap and remove the sealing ring carefully with a toothpick (do not use sharp metal things as they can damage the ring).
2. Wipe the sealing ring thoroughly with a soft cloth (or tissue). Do not use solvents. If the sealing ring is worn out or damaged replace it with a new one.
3. Clean the metal threads with a brush using ethanol. Be careful not to allow the applied liquid to get inside the flashlight or tailcap as it can cause failures in the functionality of the flashlight.

After cleaning lubricate the thread and the sealing ring with polyalphaolefin- based silica grease, e.g. Nyogel 760G. The application of other types of grease is unacceptable. In case of active operation and exploitation in dusty environments, it is recommended to perform cleaning and lubricating of the parts as often as required.

WE DO NOT RECOMMEND leaving power sources inside the flashlight for a long storage period, as batteries can leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in, previously install new and high-quality batteries, store the flashlight at an acceptable for batteries operational temperature, and revise the batteries’ state at least once a month. If you have noticed any signs of defects, withdraw the batteries from the flashlight and dispose of them.

Warranty and Service

Armytek provides free warranty repairs for 10 years (excluding batteries, chargers, switches, and connectors, which have a 2-year warranty) from the date of purchase if there is a document confirming the purchase. The warranty does not extend to damage during:

1. Improper usage.
2. Attempts to modify or repair the flashlight by nonqualified specialists.
3. Application in chlorinated, contaminated liquids or seawater.
4. Immersion into liquids in case of broken leak proofness.
5. Exposure to high temperatures and chemicals, including the liquids from defected batteries.
6. Usage of low-quality batteries.

**Germany, 10551 Berlin, Jonasstraße 6
+1 206-785-9574, service@armytek.com
www.armytek.com
REV_00-0000**

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>