RiTTO RGE2057100 REG Power Supply Installation Guide

: June 3, 2024
: RiTTO

Table of Contents

RiTTO RGE2057100 REG Power Supply
For your safety
About this document
Device overview
Installation
Wiring diagrams
Derating curve
Technical data
WERE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RiTTO RGE2057100 REG Power Supply

For your safety

DANGER HAZARD OF ELECTRIC SHOCK, OR ARC FLASH

The safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas:

Connecting to installation networks
Connecting several electrical devices
Laying electric cables
Safety standards, local wiring rules, and regulations

Failure to follow these instructions will result in death or serious injury.

About this document

In this document, you will find all information for safe installation. For further product information, follow the QR Code.

https://www.merten.de/profibereich/service/downloads.html

Scope of supply
REG Power supply, installation guide

Introduction to the TwinBus IP REG Power Supply
The TwinBus IP REG Power Supply (hereinafter referred to as the power supply) serves as the power supply for the TwinBus IP System. The power supply can also be used to supply additional TwinBus IP system components.

Device overview

A Setting output voltage 24 V … 28 V
B Port output +, –
C LED DC=ON
D Port input L, N
E Disassembly clip

The green LED DC=ON indicates that the output voltage is present.

The right place to install
The power supply is mounted on a TH 35/7.5 or TH 35/15 standard DIN rail.

Do not cover ventilation holes
Do not exceed the maximum cable length (see table below) between the components of the system The following table shows the maximum cable length between the power supply, the REG bus filter, and the system components.

Group 0.8 mm Cable Group 0.6 mm Cable Group 0.5 mm Cable

Power supply – REG Bus filter < 1 m < 1 m < 1 m
REG Bus filter – Door station 80 m 60 m 50 m
REG Bus filter – Video indoor station 80 m 80 m 50 m

If the power supply is used to supply additional system components, the following maximum cable lengths shall be considered.

Group 0.8 mm Cable Group 0.6 mm Cable Group 0.5 mm Cable

Power supply – additional Video indoor station 50 m 50 m 50 m
Power supply -Door station 50 m 50 m 50 m
Power supply – REG IP converter < 1 m < 1 m < 1 m

Group 0.8 mm cable: YR 2×0.8 mm, J-Y(ST)Y 2x2x0.8 mm, A-2Y(L)2Y 2x2x0.8 mm, CAT5e / CAT6 0.8 mm
Group 0.6 mm cable: A-2Y(L)2Y 2x2x0.6 mm, J-Y(ST)Y 2x2x0.6 mm, CAT5e / CAT6 0.8 mm
Group 0.5 mm cable: CAT5e / CAT6 0.5 mm

When using a shielded cable, the shield must not be connected.

Installation

WARNUNG DANGER TO LIFE DUE TO ELECTRIC SHOCK. THE DEVICE CAN BE DAMAGED.

The safety distance according to IEC 60664-1 must be guaranteed. Keep a distance of at least 4 mm between the individual wires of the 230 V line and the 24 V SELV wire A.
Failure to comply with this instruction may result in death or serious injury.
1. Fix the cables input L, N with a cable tie.

Wiring diagrams

As the system voltage supply

1. Terminal strip As a power supply for additional video indoor station

Derating curve

Technical data

Performance data

Input voltage AC 100 V … 240 V
Frequency 50 Hz / 60 Hz
Output voltage SELV DC 24 V … 28 V
Rated current 2.5 A
Rated power 60 W

Environmental conditions

Ambient temperature -10 °C … 50 °C
Humidity (max) 95 %
Maximum height above NN 2000 m

Dimensions and weight

Dimensions (W x H x D) 54 x 95 x 68.5 mm
Space requirement on the DIN rail 3 modules
Weight 210 g

Connection terminal

Clamping range output (conductor diameter) 1x 0.5 mm … 0.8 mm solid 1x AWG 24 … AWG 20 solid Copper-clad aluminum conductors must not be used.
Nominal torque 0.5 Nm
Housing insulation Basic insulation to neighboring DIN rail devices
Protection class The device complies with the IP30 protection class if it is installed in a distribution cabinet with at least IP30.

WERE

Dispose of the device separately from household waste at an official collection point. Professional recycling protects people and the environment against potential negative effects.

Schneider Electric GmbH c/o Ritto
Gothaer Straße 29, 40880 Ratingen

Customer Service