DS18 SLG-AR6LD Polaris Slingshot Inside Armrest Speaker Pods Owner’s Manual
- June 13, 2024
- DS18
Table of Contents
OWNER’S MANUAL
SLG-AR6LD
POLARIS SLINGSHOT INSIDE ARMREST SPEAKER
PODS WITH NXL 6BK & PRO TW1L INCLUDED
INTRODUCTION
If you’re looking to maximize sound in your Polaris Slingshot, you may consider adding these durable Polyethylene inside armrest pods by DS18. These pods include two 6.5″ Waterproof Speakers with RGB LED lights (NXL-6BK) and two 3.8″ Super bullet tweeter with RGB LED lights (PRO-TW1L) that your stereo system deserves. These pods come in pairs (Driver & Passenger) and they are very easy to Install using factory bolts that fits directly into place.
FEATURES
- Pods Sold as a Set for Driver and Passenger Sides.
- Includes one set of 6.5″ NXL-6BK Waterproof Speaker with RGB LED.
- Includes one set of 3.8″ PRO-TW1L Super Bullet Tweeter with RGB LED.
- OFC tinned wiring for more power handling and durability.
- 6 core 0.6M Input Wires for RGB Lighting and Speakers.
- Easy to install using OEM bolts and location.
- Fits Slingshot Models from 2015 or later
- Black Finish
- Durable (PE) waterproof panels with UV Protection.
- Open Baffle Speaker Pod Design.
WHAT’S IN THE BOX
- Left & Right Speaker Pods
- 2 x NXL-6BK Speakers
- 2 x PRO-TW1L Tweeters
- Speaker Wiring
INSTALLATION
-
Start by moving the seat all the way forward for easy access to this area. (Removal of the seats for easier installation on both driver and passenger sides of the vehicles is OPTIONAL) (Picture 1)
-
Remove the factory speakers inside the armrest panel using a T40 TORX Socket to loosen the (2) screws under the piece, you can open the storage compartment door to get better access to the screws in the back of this panel. (Picture 2) (Picture 3)
-
Remove the factory panel and install the new SLG-AR6LD Pods the same way that factory was pulled out. (Picture 4) (Picture 5)
-
Run the wires to the rear panel and Re-install all the screws in the same way that factory was pulled out. (Picture 6)
This concludes one side installation of the SLG-AR6LD pod, then repeat the steps 2-4 for the other side. This kit needs an aftermarket amp pre-installed with the speaker wires in this location, only after this step can you connect the speakers using the aftermarket amp’s speaker wire and RGB LED wires (optional) of the LED module (LED -BTC not included).
This concludes the installation of the SLG-AR6LD and it is ready to enjoy your new sound system upgrade!
CONNECTION OPTIONS
1. If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
| Blue LED (-)| Black 12V DC (+)
---|---|---
Red LED (-)| White Speaker (+)
Green LED (-)| Grey Speaker (-)
2. To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
- Black wire”BK” connected to battery Positive (+) 12V
- White Color Light “R”; “B” and “G” connected to battery Negative (-)
- Green Color Light “G” connected to battery Negative (-)
- Red Color Light “R” connected to battery Negative (-)
- Blue Color Light “B” connected to battery Negative (-)
- Purple Color Light “R” and “B” connected to battery Negative (-)
- Yellow Color Light”R” and “G” connected to battery Negative (-)
- Cyan Color Light “B” and “G” connected to battery Negative (-)
| Blue LED (-)| Black 12V DC (+)
---|---|---
Red LED (-)| White Speaker (+)
Green LED (-)| Grey Speaker (-)
GENERAL
Total Impedance | 4 Ohms |
---|---|
Load Configuration | Parallel |
Input Wire | 6 Core OFC Tinned (2ft / 0.6m) |
SPEAKER SPECIFICATIONS
Speaker Type / Size | 6.5″ Waterproof Coaxial with RGB LED |
---|---|
RMS Power Handling | 100W |
MAX Power Handling | 300W |
Sensitivity (1w/1m) | 91dB |
Frequency Response | 45Hz-20KHz |
Recommended Hi Pass Crossover | 65Hz |
Voice Coil Diameter | 1.2″ / 30.5mm |
Voice Coil Former Material | Kapton |
Winding Material | CCAW |
Cone Material | Injection Molded Polypropylene + UV Compliant |
Surround Material | Butyl (Rubber) |
Basket Material | High Temp Injection Molded Composite with UV Protection |
coating
Magnet Material| Ferrite+Neodymium
Magnet Weight| 14oz + 0.32oz
TWEETER SPECIFICATIONS
Speaker Type / Size | 3.8″ Super Bullet with RGB LED |
---|---|
RMS Power Handling | 60W |
MAX Power Handling | 120W |
Sensitivity (1w/1m) | 103dB |
Frequency Response | 3.5KHz-20KHz |
Recommended Hi Pass Crossover | 4KHz |
Voice Coil Diameter | 1” / 25.4mm |
Winding Material | CCA |
Diaphragm Material | Aluminum |
Magnet Material | Ferrite Y30 |
Magnet Weight | 8 Oz |
BOX SPECIFICATIONS
Box Type | Front Bafle |
---|---|
Box Material | Polyethylene (PE) |
Finish Material | Black |
UV Protection | Yes |
Waterproof Rating | IP65 |
MEASUREMENT
Overall Height | 12.66″ / 321.6mm |
---|---|
Overall Width | 26.51″ / 673.4mm |
Overall Depth | 5.94″ / 150.9mm |
MEASUREMENTS
DRIVER SIDE
DRIVER SIDE
PASSENGER SIDE
PASSENGER SIDE
WARRANTY
Please visit our website
DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without
notice.
Images may or may not include optional equipment.
WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov
FOR MORE INFORMATION
PLEASE VISIT
DS18.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>