somfy 100 io Electronic Wireless Roller Shutter Motor Instruction Manual

: June 16, 2024
: somfy

Table of Contents

TRANSLATED VERSION
GENERAL INFORMATION
INTRODUCTION
INSTALLATION
WIRING
USE AND MAINTENANCE
TECHNICAL DATA
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

somfy 100 io Electronic Wireless Roller Shutter Motor Instruction Manual

TRANSLATED VERSION

This instructions guide applies to all versions of the TUBELITE WHITE RECEIVER 100 io and TUBELITE WHITE RECEIVER 200 io.

GENERAL INFORMATION

Safety instructions

Danger
Indicates a hazard resulting in immediate death or serious injury.
Warning
Indicates a hazard which may result in death or serious injury.
Caution
Indicates a hazard which may result in minor or moderate injury.
Attention
Indicates a hazard which may result in damage to or destruction of the product.

INTRODUCTION

FIELD OF APPLICATION

The TUBELITE WHITE RECEIVER 100 io and TUBELITE WHITE RECEIVER 200 io are receivers equipped with io-homecontrol® radio technology. They enable you to independently control one or two white LED light source(s) connected to the constant voltage output(s) (24 V), via a Somfy io-homecontrol® control point, e.g. Situo 1 or 5 Variation io (for more details, contact your retailer).
These receivers enables you to vary the light intensity of the LED lights, and program a favourite light intensity, i.e. the favourite position: this favourite position can for instance be set to night-lighting. The factory default setting for the favourite light intensity is 50% of the maximum intensity.
Their shape enables the manufacturers to install them discreetly in the fabric rolling tube on the other end from the drive, connecting them directly to the mains power supply.
These receivers’ IP44 index protection rating makes them suitable for outdoor use, and ideal for controlling the lighting of an awning or a rail-guided fabric pergola (RGS).

LIABILITY

Before installing and using the receiver, please read this instructions guide carefully.
It must be installed by a home automation professional, in accordance with Somfy’s instructions and the regulations applicable in the country in which it is commissioned.
Any operation of the receiver outside the field of application described above is prohibited. Such use, and any failure to comply with the instructions given in this instructions guide, would exempt Somfy of any liability and invalidate the warranty.
The installer must inform their customers of the operating and maintenance conditions of the receiver, and must provide them with the operating and maintenance instructions after installing it. Any After-Sales Service operation on the receiver must be performed by a home automation professional.
Never begin installing without first checking the compatibility of this product with the associated equipment and accessories.
In case of any doubt when installing the receiver or for additional information, consult a Somfy contact or visit www.somfy.com.

INSTALLATION

ASSEMBLY

Warning

These instructions are mandatory for the home automation professional installing this product.
Comply with current standards and legislation in the country of installation.

Caution

Comply with standard NF C 15-100 relating to electrical installations.
Make sure that the power of the LED lights connected to the receiver does not exceed 4.2 A per output.

Attention

Cables passing through a metal wall must be protected and insulated using a sheath or sleeve.
Secure the cables to prevent any contact with moving parts.
The receiver cable cannot be removed. If it is damaged, return the receiver to the After-Sales service.
To ensure good radio reception, ensure that the outside antenna is not in contact with any metal item.
Do not trim the antenna wire.
Never drop, knock, drill or submerge the product.

Tubelite preparation

Fit the accessories required for incorporating the Tubelite into the roller tube on the other end from the drive using the crown a and the drive wheel b on the Tubelite.
Measure the length (L) between the inner edge of the Tubelite head and the rim of the drive wheel.

Tube preparation
On the other end from the drive, deburr the roller tube and remove the swarf.

Tubelite-tube assembly

Slide the Tubelite into the roller tube.
Lock the drive wheel to prevent movement along the roller tube:
- This can be done either by fastening the roller tube on the drive wheel using Ø 5 mm self-tapping screws, or Ø 4.8 mm steel pop rivets positioned 5 mm to 15 mm from the outer rim of the drive wheel, regardless of the roller tube.

Attention

The screws or pop rivets must only be fastened on the drive wheel, and not on the Tubelite.

Alternatively, a drive wheel stop can be used for non-smooth tubes.

Fitting the tube-Tubelite assembly

Mount and fasten the tube-Tubelite and drive assembly on the Tubelite bracket c and the motor head bracket d:

Attention
Ensure that the tube-Tubelite and drive assembly is locked on the Tubelite bracket and the drive bracket. This operation prevents the tube-Tubelite and drive assembly from coming out of the mounting brackets.
Fit the stop rings e according to the bracket type.

WIRING

Danger
Cut off the mains power supply.

Connect the receiver to one or more white LED lights (A) or (B) and to the mains power supply (C), adhering to the polarity, as per the table and illustration below.
Wiring Instruction

Tubelite white receiver 100 io connectors (A)
LED light no.1

Tubelite white receiver 200 io connector (B)
LED light no.1
LED light no.2

Power supply (C)
Blue wire (N)
Brown wire (L)
220-240 V AC

The connectors are compatible with TELECO lighting solutions, otherwise use the accessory ref. 9029053, not supplied (transparent cable: 0 V, white cable: 24 V).

Warning

By default, the unconnected receiver output cable on the TUBELITE WHITE RECEIVER 200 io is protected and insulated by a cap. Remove this if using a second LED light.

COMMISSIONING

This instructions guide only describes commissioning using a io control point.
For commissioning using any other io control point, refer to the corresponding instructions guide.
Blue wire

Programming the first Somfy io control point on an LED light

Power on.
Press the Up and Down buttons simultaneously on the io control point, and follow procedure 2.3.1.1. or 2.3.1.2. according to the reaction of the LED light(s).

An LED light comes on then goes out

Scenario no.1: It is for this LED light that the control point must be programmed.

Briefly press the PROG button on this io control point. The LED light comes on then goes out.
The io control point has been programmed for this LED light.

Scenario no.2: It is not for this LED light that the control point must be programmed.

Press the Up and Down buttons again simultaneously on the io control point, and repeat if necessary until the desired LED comes on then goes out.

If the output selected is not connected to any LED light, nothing will come on. Select a different output.

Briefly press the PROG button on this io control point.
The LED light comes on then goes out.
The io control point has been programmed for this LED light.

No LED light comes on

Press the Up button.

If one or more LED light(s) come(s) on:
The io control point has been programmed for the LED lights lit.
- Go to section 2.3.2.
If no LED light comes on:
Check the condition of the LED lights, the wiring, and try again.
- Go to section 2.4.3.

Activating/deactivating automatic switch-of

Prerequisite : Commissioning has been completed using an io control point.
This function allows an LED light to be switched off automatically after 3, 6 or 12 hours of operation. This duration can be configured (see 2.3.3.).
By default, this function is deactivated.
Setting the operating duration

Setting the operating duration

You can configure the operating duration of each LED light before automatic switch-off.
The default setting is 6 hours.
To alter these settings, for each LED light:

Briefly press the my and Down buttons simultaneously on the io control point.
Immediately afterwards, press and hold the my and Down buttons simultaneously until the LED light comes on then goes out.
- Briefly press the Down button to set the duration to 3 hours.
- Or briefly press the my button to set the duration to 6 hours.
- Or briefly press the Up button to set the duration to 12 hours.
  The LED light comes on then goes out.
Press the my button until the LED light comes on then goes out. The new setting has been programmed.

INSTALLATION TIPS AND ADVICE

Questions about the receiver?

Observations	Possible causes	Solutions

The LED light does not react at all when a button is pressed on the control point| The control point is not programmed in the receiver.| Follow the commissioning procedure (see 2.3. )
The control point batteries are low.| Replace the batteries, using batteries with the same specifications.
The control point used is not compatible with the receiver.| Ensure that the two products are compatible.
The mains power supply is faulty.| Check the power supply.
The wiring is incorrect.| Check the wiring (see 2.1. )
The LED light does not come on.| The ambient temperature is high (> 45°C).| Wait for the temperature to cool down.
Poor radio performance.| The antenna is damaged.| Contact the After-Sales service.

Replacing a lost or broken io control point
Reset to the original configuration (see 2.3.3.), and repeat the commissioning steps (see 2.3.).

Factory mode

Attention

Only deactivate the power to the receiver to be reset!
This reset deletes all programmed control points.

Switch off the mains power supply for 4 s.
Switch the mains power supply back on for approximately 10 seconds (for at least 5 seconds but no longer than 15 seconds).
Switch off the mains power supply for 4 s.
Switch the mains power supply back on.
All the LED lights come on then go out.
Press the PROG button on the 1 W io control point until all the LED lights come on then go out twice.

The receiver is reset to its original configuration.

Repeat the commissioning procedures (see 2.3.).

USE AND MAINTENANCE

This product is maintenance-free.

UP AND DOWN BUTTONS

To switch the LED light on:
- Briefly press the Up button.
To switch the LED light off:
- Briefly press the Down button

On Situo Variation 1 or 5 (A/M) io control points, pressing and holding the up or down buttons has no effect.

TECHNICAL DATA

TUBELITE WHITE RECEIVER 100 io	TUBELITE WHITE RECEIVER 200 io
Number of outputs	1
Max. output peak current	4.2 A max.
Compatible lamp power or range of lamp powers	100 W max.

output
Length (excluding head)| 662 mm
Roller tube minimum diameter| 50 x 1.5 mm
Maximum number of associated control points| 3| 3 per output
Maximum number of associated control points| Unlimited
Radio frequency| 868-870 MHz io-homecontrol®, two-way tri-band
Frequency bands and maximum power used| 868.000 MHz – 868.600 MHz e.r.p. <25 mW 868.700 MHz – 869.200 MHz e.r.p. <25 mW869.700 MHz – 870.000 MHz e.r.p. <25 mW
Index protection rating| IP 44
Electrical insulation| Class II
Operating temperature| -20°C to +45°C
Maximum altitude| 2000 m
Compatible lamp types| LED strips or spot lights controlled at constant voltage
Light management| Light intensity variation only(The colour temperature variation is unavailable)
Input power supply| 220-240 V AC / 50 Hz
Power supply cable size| 7.5 m
Output voltage| 24 V DC
Contact temperature| Tc = 90°C
Built-in timer function| OFF / 3h /6h / 12h

SOMFY ACTIVITES SA hereby declares that the radio equipment covered by these instructions complies with the requirements of Radio Directive 2014/53/EU and the other essential requirements of the applicable European Directives.
The full text of the EU declaration of conformity is available at www.somfy.com/ce.

UKCA Icon
Somfy limited, Yeadon LS19 7ZA UK, hereby declares that the radio equipment covered by these instructions is in compliance with the requirements of UK legislation: the Radio Equipment
Regulations S.I. 2017 N°1206. The full text of the UKCA declaration of conformity is available at www.somfy.co.uk