Blackview airbuds 6 AirBuds Auricolari Bluetooth 5.3 Cuffie Wireless In Ear User Guide
- June 13, 2024
- Blackview
Table of Contents
Blackview airbuds 6 AirBuds Auricolari Bluetooth 5.3 Cuffie Wireless In Ear
Product Introduction
Device Connection
-
Open the cover of the charging box and a pair of headsets are in the charging box. When the indicator light of the charging box is green and the indicator light of the headset is red and blue, the headset enters the “Pairing State”.
-
Turn on bluetooth of the device and select “AirBus 6”; Click it and after the connection is successful, there will be a voice broadcast with a connection prompt tone.
Note : The above is the first pairing method. In subsequent use, the earbuds will be automatically turned on and connected after being taken out of the earbuds box.
Specification Parameters
Model : AirBuds 6
Bluetooth version : 5.3
Battery type : Polymer Lithium Battery
Effective receiving distance of bluetooth : ≥ 10m
Bluetooth frequency : 2.402 ~ 2.485 GHz
Moving coil specification : Φ 13mm
Dynamic frequency response : 20Hz-20KHz
Battery capacity (charging box) : 320 mAh
Charging time (charging box) : < 1.5 hours
Charging time (headsets) : < 1.5 hours
Running time : 5 hour
Operation Method
| Left Ear| Right Ear
---|---|---
Start Siri| Long press the “Touch” button for 1 second and (hear “beep” sound)
release
Pause / play music| Double click the “Touch” button
Last one| Triple click the “Touch” button| None
Next one| None| Triple click the “Touch” button
Answer| Double click the “Touch” button when an incoming call comes in
Hang up| Double click the “Touch” button during a call
Reject| Long press the button for 2S (hear the “beep” sound) release during
the incoming call status
volume plus| None| Single click the “Touch” button
volume down| Single click the “Touch” button| None
Restore factory settings| Click the “Touch” button four times
Charging with Charging Box
The headset can be charged in the charging box through the type-C interface,
and the white light flashes during charging When the headset is fully charged,
the white light is always on.
Light Indication
| Headphone mode | Status |
|---|---|
| Power on | The blue light is on for 2S |
| Power off | The red light is on for 2S |
| pairing | Red and blue lights flash alternately |
| Connected (standby) | The blue light flashes once in 5S |
| Play music / call status | Lights go out |
| Incoming call | Blue light double flashes fast in 2s |
| Headset low power state | Red light double flashes fast in 5s |
| Headset charging (less than 70% power) | The red light of headset is on for 3S |
and then goes out
Headset charging (more than 70% power)| The blue light of headset is on for 3S
and then goes out
The headset is fully charged| Lights go out
Low battery of charging box| The green light flashes and goes out after 4S
The charging box is charging| The white light flashes
The charging box is fully charged| The white light is always on
Restore factory settings| The red and blue lights flash together for 3 times
and then go out
Answers for Common Questions
-
The bluetooth headset cannot be switched on.
Reason: The battery in the charging compartment is low or the power of the bluetooth headset is low.
Solution: Put the headset into the charging box, close the cover, and charge the charging box for more than 1 hour before use. -
The phone cannot search for bluetooth headset.
Reason: 1. The Bluetooth headset is not in the pairing state;
Solution: Put the headset back into the charging box, close and then open the cover, wear the headset, and the headset (i.e. the red and blue lights flash alternately) enters the bluetooth pairing state; You can also click the “Touch” button for four times (the headset power off) to reset it.
Reason:2. There are mobile phone bluetooth program errors;
Solution: After the bluetooth of the mobile phone is restarted, clear all pairing data stored in the the mobile phone; Search for bluetooth again. -
There is no sound from the headset speaker
Reason: 1. Turn the volume of the mobile phone and headset to the maximum and confirm whether it is caused by volume adjustment.
Solution: When the headset is connected, adjust the volume of the mobile phone;
Reason: 2. The Bluetooth headset is not properly connected with the mobile phone.
Solution: Reconnect bluetooth and mobile phone through pairing.
Reason: 3. The Bluetooth headset is not within the valid working range.
Solution: Keep the headset within 10 meters of the mobile phone, and there are no large objects, walls and other obstacles between the headset and the device. -
The headset doesn’t send messages or the voice is low.
Reason: 1. The Bluetooth headset is too far from the mouth;
Solution: The bluetooth headset should be worn on the ear for normal use;
Reason: 2. The microphone hole of Bluetooth is blocked or water has entered;
Solution: Remove the blockage of the microphone hole or prevent water from entering the microphone hole. -
The headphone get stuck or disconnected when talking or listening to music.
Reason: 1. The Bluetooth headset is too far away from the mobile phone or there are obstacles.
Solution: 1. Keep the headset within 10 meters of the mobile phone, and there are no large objects and walls between the headset and the device. Be careful not to cover the bluetooth headset with your hand. In order to maintain the continuous stability of the signal, please try to keep the bluetooth and the mobile phone in the same direction.
Reason: 2. There is a problem with the bluetooth signal of the mobile phone or there is strong signal interference nearby.
Solution: It is best not to make the mobile phone close to metal objects. You can also change another mobile phone or try another place.
Reason: 3. The power of bluetooth headset is insufficient. Please charge the headset as soon as possible.
Solution: Please charge the headset as soon as possible. -
There is no sound in the headset during voice call, and the sound comes out of the mobile phone.
Reason: The headset is operated during a voice call or call. Double click the headset.
Solution: Turn off the bluetooth of the mobile phone and then turn it on, or put the headset into the box, close the cover, turn off the headset and then open the cover; The headset does not support the connection or hanging up of voice calls. If there is a voice call, please connect or hang up on the mobile phone.
(Note: at present,the headset only supports incoming calls from GSM cards, not app network calls.) -
After the headset is put into the box and the cover is closed, the headset is not disconnected.
Reason: 1. The charging box is completely dead;
Solution: Charge the charging box;
Reason: 2. The headset is not put into the box properly, and the communication between the headset and the base is abnormal.
Solution: Reopen the charging box, take out the headset from the box, and then put it into the box.
When the headset is put into the box, the green light on the charging box will light once and close the cover.
Reason: 3. The charging box is damaged.
Solution: Replace the charging box.
Attention
- Please use standard charging cable and adapter to avoid damage and accidents.
- Please avoid using corrosive cleaning detergent to clean this product.
- Please avoid product usage in the rain and keep away from heating or fire.
Maintenance
Please follow the following suggestions to prolong product working life.
- Keep product dry and don’t put in damp places in case of affecting internal circuit.
- Aviod product usage during intense sporting or on sweating occasions in case sweat infiltrate into product and cause damages.
- Keep off sunlight or high temperature in case of shortening working life of electric parts battery damage, plastic parts deformation.
- Keep off intense vibration and impact from hard material in case of internal circuit damages.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>