SATCO S11605 LED Edge Lit 8 Round Recessed Down Light Instruction Manual
- June 16, 2024
- SATCO
Table of Contents
LED EDGE LIT 4″, 6″ & 8″
ROUND RECESSED DOWNLIGHTS
Models: S11600, S11601, S11602, S11603, S11604, S11605, S11606, S11607,
S11608
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
- Disconnect power before installation or any maintenance of the fixture.
- To avoid damage, falling, electric shock or fire, do not modify the fixture or replace accessories without confirming with the supplier first.
- Only authorized, qualified personnel should install this fixture and should follow the owner’s manual.
- Do not dismantle the fixture without the supplier’s authorization.
- Do not touch the power supply when the fixture is operating.
- For use in environments where an accumulation of non-conductive dust on the fixture may be expected.
- Suitable for indoor/outdoor installations.
IMPORTANT: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Fixture Includes:
1 LED Lamp
1 Junction Box
Model
| Dimensions| Watts| Volts| CCT| CRI| Finish
---|---|---|---|---|---|---
S11600| 4 inches| 10W| 120V|
3000K
|
90
|
White
S11601
| 4000K
S11602|
5000K
S11603
|
6 inches
|
12W
| 3000K
S11604
|
4000K
S11605
|
5000K
S11606
|
8 inches
|
24W
|
3000K
S11607
|
4000K
S11608
|
5000K
WIRING DIAGRAM
- Power supply
- White wires
- Black wires
- Quick connect terminals
- Green wires
- Cable to fixture
INSTALLATION
TOOLS REQUIRED: Hole saw, measuring tape and connector cables (as needed).
NOTE: Use extensions if necessary. Available connector cables are 6′ (1.8m). Connector cables are linkable.
1. Turn power OFF from the electrical panel before starting installation.
2. Cut a hole in the ceiling for the downlight in a suitable position. Refer
to Hole Cut Dimension chart (below).
3. Run the electrical wire from the switch (power supply wire) through the
mounting hole. Use NMD90 Romex or BX cable. See Figure A.
Figure A
4. Open the Junction Box swing cover and remove the appropriate knockouts.
5. Insert the power supply wire through the knockout and fasten with a cable
connector (not included).
6. Connect wires inside the Junction Box using the quick connect terminals.
Connect green ground with the green box wire. Connect the black and white
power leads with the matching black and white box wires. See Wiring Diagram.
7. Put all wires and connections back into the box and close the cover
securely.
8. New Construction Applications: Junction Box shall be firmly secured to
the studs, joists or similar fixed structural units.
Remodel Applications: Do not require the Junction Box to be firmly
secured to fixed structural units. Remove the Junction Box tabs, then insert
into ceiling.
9. Bend back the two torsion springs and slowly fit the fixture through the
ceiling hole. The torsion springs will pull the fixture into place. See
Figures B & C.
Figures B
Figures C
10. Once installation is complete, turn power ON to confirm the fixture is working properly.
Hole Cut Dimensions:
4″ fixture = ø 4 1/4″ (108mm)
6″ fixture = ø 6 3/16″ (157mm)
8″ fixture = ø 8 1/8″ (206mm)
© Copyright 2019 Satco Products, Inc.
Satco Products, Inc.
Brentwood, NY 11717
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>