SATCO S11600 LED Edge Lit 46 Round Recessed Down Light Instruction Manual
- June 16, 2024
- SATCO
Table of Contents
SATCO S11600 LED Edge Lit 46 Round Recessed Down Light
Specifications
| Model | Dimensions | watts | Volts | CCT | SHOUT | Finish |
|---|---|---|---|---|---|---|
| S11600 | 4 inches | 10W | – | 3000K | – | – |
| S11601 | 4 inches | 10W | – | 4000K | – | – |
| S11602 | 4 inches | 10W | – | 5000K | – | – |
| S11603 | 4 inches | 10W | – | 3000K | – | – |
| S11604 | 6 inches | 12W | 120V | 4000K | 90 | White |
| S11605 | 6 inches | 12W | 120V | 5000K | – | – |
| S11606 | 6 inches | 12W | 120V | 3000K | – | – |
| S11607 | 8 inches | 24W | – | 4000K | – | – |
| S11608 | 8 inches | 24W | – | 5000K | – | – |
Installation and Safety Instructions
WARNING: Risk of Fire or Electric Shock
IMPORTANT: This product must be installed by the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Fixture Includes
- 1 LED Lamp
- 1 Junction Box
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT : Read before installing the fixture. Retain for future
reference.
WARNING : Risk of Fire or Electric Shock
- Disconnect power before installation or any maintenance of the fixture.
- To avoid damage, falling, electric shock or fire, do not modify the fixture or replace accessories without confirming with the supplier first.
- Only authorized, qualified personnel should install this fixture and should follow the owner’s manual.
- Do not dismantle the fixture without the supplier’s authorization.
- Do not touch the power supply when the fixture is operating.
- For use in environments where an accumulation of non-conductive dust on the fixture may be expected.
- Suitable for indoor/outdoor installations.
IMPORTANT : This product must be installed under the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Model| Dimensions| Watts| Volts| CCT| CRI|
Finish
---|---|---|---|---|---|---
S11600|
4 inches
|
10W
|
120V
| 3000K|
90
|
White
S11601| 4000K
S11602| 5000K
S11603|
6 inches
|
12W
| 3000K
S11604| 4000K
S11605| 5000K
S11606|
8 inches
|
24W
| 3000K
S11607| 4000K
S11608| 5000K
WIRING DIAGRAM
INSTALLATION
TOOLS REQUIRED: Hole saw, measuring tape and connector cables (as
needed). NOTE: Use extensions if necessary. Available connector cables are 6′
(1.8m). Connector cables are linkable.
-
Turn the power OFF from the electrical panel before starting installation.
-
Cut a hole in the ceiling for the downlight in a suitable position. Refer to the Hole Cut Dimension chart (below).
-
Run the electrical wire from the switch (power supply wire) through the mounting hole. Use NMD90 Romex or BX cable. See Figure A.
-
Open the Junction Box swing cover and remove the appropriate knockouts.
-
I nsert the power supply wire through the knockout and fastened it with a cable connector (not included).
-
Connect wires inside the Junction Box using the quick-connect terminals. Connect green ground with the green box wire. Connect the black and white power leads with the matching black and white box wires. See Wiring Diagram.
-
Put all wires and connections back into the box and close the cover securely.
-
New Construction Applications: Junction Box shall be firmly secured to the studs, joists or similar fixed structural units.
Remodel Applications: structural units. Remove the Junction Box tabs, then insert them into the ceiling. -
Bend back the two torsion springs and slowly fit the fixture through the ceiling hole.
The torsion springs will pull the fixture into place. See Figures B & C. -
Once installation is complete, turn the power ON to confirm the fixture is working properly.
Hole Cut Dimensions
- 4″ fixture = 0 4 1/4″ (108mm)
- 6″ fixture = 0 6 3/16″ (157mm)
- 8″ fixture = 0 8 1/8″ (206mm)
FAQ
Frequently Asked Questions
- Q: Can this downlight be used in damp locations?
- A: No, this downlight is not rated for damp locations.
- Q: Can I use a dimmer switch with this downlight?
- A: Yes, this downlight is compatible with most standard dimmer switches.
- Q: What is the lifespan of the LED lamp?
- A: The LED lamp has an estimated lifespan of 50,000 hours.
- Q: Can I install this downlight in an insulated ceiling?
- A: Yes, this downlight is IC-rated and can be installed in direct contact with insulation.
Copyright 2019 Satco Products, Inc. 1/19
Satco Products, Inc. Brentwood, NY 11717 https://manual-hub.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>