SATCO NUVO S11603 LED EDGE LIT 4 Inch Round Recessed Downlights Instruction Manual
- June 16, 2024
- SATCO
Table of Contents
SATCO NUVO S11603 LED EDGE LIT 4 Inch Round Recessed Downlights
Specifications
| Model | Dimensions | Watts | Volts | CCT | CRI | Finish |
|---|---|---|---|---|---|---|
| S11600 | 4 inches | 10W | – | 3000K | – | – |
| S11601 | 4 inches | 10W | – | 4000K | – | – |
| S11602 | 4 inches | 10W | – | 5000K | – | – |
| S11603 | 4 inches | 10W | – | 3000K | – | – |
| S11604 | 6 inches | 12W | 120V | 4000K | 90 | White |
| S11605 | 6 inches | 12W | 120V | 5000K | – | – |
| S11606 | 6 inches | 12W | 120V | 3000K | – | – |
| S11607 | 8 inches | 24W | – | 4000K | – | – |
| S11608 | 8 inches | 24W | – | 5000K | – | – |
Installation and Safety Instructions
WARNING: Risk of Fire or Electric Shock
- Disconnect power before installation or any maintenance of the fixture.
- To avoid damage, falling, electric shock, or fire, do not modify the fixture or replace accessories without confirming with the supplier first.
- Only authorized, qualified personnel should install this fixture and should follow the owner’s manual.
- Do not dismantle the fixture without the supplier’s authorization.
- Do not touch the power supply when the fixture is operating.
- For use in environments where an accumulation of non-conductive dust on the fixture may be expected.
- Suitable for indoor/outdoor installations.
IMPORTANT
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Fixture Includes: 1 LED Lamp, 1 Junction Box
Wiring Diagram
Installation
TOOLS REQUIRED: Hole saw, measuring tape, and connector cables (as needed).
NOTE: Use extensions if necessary. Available connector cables are 6′ (1.8m). Connector cables are linkable.
-
Turn the power OFF from the electrical panel before starting installation.
-
Cut a hole in the ceiling for the downlight in a suitable position. Refer to the Hole Cut Dimension chart.
-
Run the electrical wire from the switch (power supply wire) through the mounting hole. Use NMD90 Romex or BX cable. See Figure A.
-
Open the Junction Box swing cover and remove the appropriate knockouts.
-
Insert the power supply wire through the knockout and fasten it with a cable connector (not included).
-
Connect wires inside the Junction Box using the quick-connect terminals. Connect green ground with the green box wire. Connect the black and white power leads with the matching black and white box wires. See Wiring Diagram.
-
Put all wires and connections back into the box and close the cover securely.
-
New Construction Applications: Junction Box shall be firmly secured to the studs, joists, or similar fixed structural units.
Remodel Applications: Remove the Junction Box tabs, then insert them into the ceiling. -
Bend back the two torsion springs and slowly fit the fixture through the ceiling hole.
The torsion springs will pull the fixture into place. See Figures B & C. -
Once installation is complete, turn the power ON to confirm the fixture is working properly.
Hole Cut Dimensions -
4″ fixture = 0 4 1/4″ (108mm)
-
6″ fixture = 0 6 3/16″ (157mm)
-
8″ fixture = 0 8 1/8″ (206mm)
Contact Information
Satco Products, Inc. Brentwood, NY 11717
Website: https://manual-hub.com/
FAQ
Q: Can I use this downlight for outdoor applications?
A: No, this downlight is designed for indoor use only.
Q: What is the maximum wattage for these downlights?
A: The maximum wattage varies depending on the model. Please refer to the Specifications section for the wattage of each model.
Q: Are the connector cables included with the downlights?
A: No, the connector cables are not included. They need to be purchased separately.
Q: Can I use a dimmer switch with these downlights?
A: Yes, these downlights are compatible with most standard dimmer switches. Please ensure that the dimmer switch is compatible with LED lighting.
Q: What is the CRI (Color Rendering Index) of the downlights?
A: The CRI is not specified for all models. Please refer to the Specifications section for the CRI of each model.