SATCO S11600 Round Recessed Downlights Instruction Manual
- June 16, 2024
- SATCO
Table of Contents
SATCO S11600 Round Recessed Downlights
Product Information
Specifications:
| Model | Dimensions | Watts | Volts | CCT | CRI | Finish |
|---|---|---|---|---|---|---|
| S11600 | 4 inches | 10W | – | 3000K | – | – |
| S11601 | 4 inches | 10W | – | 4000K | – | – |
| S11602 | 4 inches | 10W | – | 5000K | – | – |
| S11603 | 4 inches | 10W | – | 3000K | – | – |
| S11604 | 6 inches | 12W | 120V | 4000K | 90 | White |
| S11605 | 6 inches | 12W | 120V | 5000K | 90 | – |
| S11606 | 6 inches | 12W | 120V | 3000K | 90 | – |
| S11607 | 8 inches | 24W | – | 4000K | – | – |
| S11608 | 8 inches | 24W | – | 5000K | – | – |
Installation and Safety Instructions:
WARNING: Risk of Fire or Electric Shock
IMPORTANT: This product must be installed in accordance with the
applicable installation code by a person familiar with the construction and
operation of the product and the hazards involved.
Installation:
TOOLS REQUIRED: Hole saw, measuring tape, connector cables (as needed),
and extensions (if necessary). Available connector cables are 6′ (1.8m).
Connector cables are linkable.
- Turn power OFF from the electrical panel before starting installation.
- Cut a hole in the ceiling for the downlight in a suitable position. Refer to the Hole Cut Dimension chart below.
- Run the electrical wire from the switch (power supply wire) through the mounting hole. Use NMD90 Romex or BX cable. See Figure A.
- Open the Junction Box swing cover and remove the appropriate knockouts.
- Insert the power supply wire through the knockout and fasten with a cable connector (not included).
- Connect wires inside the Junction Box using the quick connect terminals. Connect green ground with the green box wire. Connect the black and white power leads with the matching black and white box wires. See Wiring Diagram.
- Put all wires and connections back into the box and close the cover securely.
- New Construction Applications: Junction Box shall be firmly secured to the studs, joists, or similar fixed structural units. Remodel Applications: Remove the Junction Box tabs, then insert into the ceiling.
FAQ:
-
Q: What are the available models of LED EDGE LIT round recessed downlights?
A: The available models are S11600, S11601, S11602, S11603, S11604, S11605, S11606, S11607, and S11608. -
Q: What are the dimensions and specifications of the different models?
A: Refer to the Specifications section above for the dimensions and specifications of each model. -
Q: What tools are required for installation?
A: The tools required for installation are a hole saw, measuring tape, connector cables (as needed), and extensions (if necessary). -
Q: How should I wire the downlight?
A: Follow the Wiring Diagram provided in the manual. Connect the power supply wire through the knockout in the Junction Box and use quick connect terminals to connect the wires inside the box. -
Q: Can I use these downlights for new construction and remodel applications?
A: Yes, these downlights can be used for both new construction and remodel applications. For new construction, the Junction Box should be firmly secured to the studs, joists, or similar fixed structural units. For remodel applications, remove the Junction Box tabs and insert it into the ceiling.
Product Using Instructions
WARNING: Risk of Fire or Electric Shock
IMPORTANT: This product must be installed by the applicable installation
code by a person familiar with the construction and operation of the product
and the hazards involved.
Fixture Includes: 1 LED Lamp, 1 Junction Box
Facility
TOOLS REQUIRED: Hole saw, measuring tape, and connector cables (as
needed).
NOTE: Use extensions if necessary. Available connector cables are 6′
(1.8m). Connector cables are linkable.
- Turn power OFF from the electrical panel before starting installation.
- Cut a hole in the ceiling for the downlight in a suitable position. Refer to Hole Cut Dimension chart below.
- Run the electrical wire from the switch (power supply wire) through the mounting hole. Use NMD90 Romex or BX cable. See Figure A.
- Open the Junction Box swing cover and remove the appropriate knockouts.
- Insert the power supply wire through the knockout and fasten with a cable connector (not included).
- Connect wires inside the Junction Box using the quick connect terminals. Connect green ground with the green box wire. Connect the black and white power leads with the matching black and white box wires. See Wiring Diagram.
- Put all wires and connections back into the box and close the cover securely.
- New Construction Applications: Junction Box shall be firmly secured to the studs, joists, or similar fixed structural units. Remodel Applications: structural units. Remove the Junction Box tabs, then insert into ceiling.
Models: S11600, S11601, S11602, S11603, S11604, S11605, S11606, S11607, S11608
Fixture Includes
- 1 LED Lamp
- 1 Junction Box
SAFETY INSTRUCTIONS
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
- Disconnect power before installation or any maintenance of the fixture.
- To avoid damage, falling, electric shock or fire, do not modify the fixture or replace accessories without confirming with the supplier first.
- Only authorized, qualified personnel should install this fixture and should follow the owner’s manual.
- Do not dismantle the fixture without the supplier’s authorization.
- Do not touch the power supply when the fixture is operating.
- For use in environments where an accumulation of non-conductive dust on the fixture may be expected.
- Suitable for indoor/outdoor installations.
IMPORTANT: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
SPECIFICATIONS
Model| Dimensions| Watts| Volts| CCT| CRI|
Finish
---|---|---|---|---|---|---
S11600|
4 inches
|
10W
|
120V
| 3000K|
90
|
White
S11601| 4000K
S11602| 5000K
S11603|
6 inches
|
12W
| 3000K
S11604| 4000K
S11605| 5000K
S11606|
8 inches
|
24W
| 3000K
S11607| 4000K
S11608| 5000K
WIRING DIAGRAM
INSTALLATION
TOOLS REQUIRED: Hole saw, measuring tape and connector cables (as needed).
NOTE: Use extensions if necessary. Available connector cables are 6′ (1.8m). Connector cables are linkable.
- Turn power OFF from the electrical panel before starting installation.
- Cut a hole in the ceiling for the downlight in a suitable position. Refer to Hole Cut Dimension chart (below).
- Run the electrical wire from the switch (power supply wire) through the mounting hole. Use NMD90 Romex or BX cable. See Figure A.
- Open the Junction Box swing cover and remove the appropriate knockouts.
- the power supply wire through the knockout and fasten with a cable connector (not included).
- Connect wires inside the Junction Box using the quick-connect terminals. Connect green ground with the green box wire. Connect the black and white power leads with the matching black and white box wires. See Wiring Diagram.
- Put all wires and connections back into the box and close the cover securely.
- New Construction Applications: Junction Box shall be firmly secured to the studs, joists or similar fixed structural units. Remodel Applications: Do not require the Junction Box to be firmly secured to fixed structural units. Remove the Junction Box tabs, then insert into the ceiling.
- Bend back the two torsion springs and slowly fit the fixture through the ceiling hole. The torsion springs will pull the fixture into place. See Figures B & C.
- Once installation is complete, turn the power ON to confirm the fixture is working properly.
Hole Cut Dimensions
- 4″ fixture = 0 4 1/4″ (108mm)
- 6″ fixture = o 6 3/16″ (157mm)
- 8″ fixture = 0 8 1/8″ (206mm)
Satco Products, Inc.
Brentwood, NY 11717
© Copyright 2019 Satco Products, Inc. 1/19
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>