Shenzhen F15 Bluetooth Headset Open Wearable Stereo User Guide
- May 15, 2024
- Shenzhen
Table of Contents
OPEN WEARABLE STEREO
OWS HEADSET
User Guide
• Power on/off
Power on: After leaving the compartment, the machine will automatically turn on and enter the pairing state. (Manual power on) Press and hold the button for about3 seconds, the white and blue lights will flash quickly for 200ms, and then turn off after connecting.
Power off: Put the headphones into the charging compartment and enter the charging state. The headphones will automatically shut down and disconnect. (Manual shutdown) Press and hold the button for about 5 seconds, and the white and blue lights will flash three times before going out.
• Earphone pairing
- In pairing mode, the white and blue lights of the earphones L and R flash quickly for 200ms at the same time
- After successful pairing, you can connect the device on the phone page, with the left ear light off and the right ear white blue light flashing quickly. After connecting the phone, the light goes off and the voice prompt “Pairing successful” appears.
- After connecting to the phone, the voice prompts “Bluetooth connected”.
- Pairing timeout, if the phone is not connected after powering on, it will automatically shut down after 3 minutes.
• Function operation
- Answer Click the left and right buttons at will, and the voice prompt “answer ” will appear.
- Hang up: Double click the left and right buttons, and the voice prompt “Hang up” will appear.
- Volume increase or decrease during a call: Press and hold the left ear button for about 1 second before the volume begins to decrease; Release and stop/Press and hold the right ear button for about 1 second, and the volume starts to increase. Release and stop; Voice prompt ‘DI’.
- Listening/Pause: Click the left and right buttons at will, and the voice prompt will be ‘DI’.
- Previous/Next Song: Three clicks on the L ear button (previous song)/Three clicks on the R ear button (next song)
- Volume increase/decrease: Double click on the L ear button for volume -/Double click on the R ear button for volume+, and the voice prompt will be ‘DI’.
- Voice Assistant: Press and hold the left and right buttons for about 3 seconds to release and enter the voice assistant. Click to exit, and the voice prompt will be ‘DI’.
- Caller ID: Ring after calling the number.
- Call rejection: Press and hold the left and right buttons for about 2 seconds.
- Voice switching: When the phone is not connected when turned on, the white and blue lights flash. Double click the left and right buttons, and the voice prompt “Chinese mode” will appear.
- Subwoofer mode/HIFI music mode: Press any of the left and right buttons four times to enter the subwoofer music mode. Press again four times to exit and enter HIFI music mode. (When the headphones are turned off and turned on again, the mode remains the same as before).
- Reset the headphones: Press and hold the left and right buttons for about 8 seconds to reset. After successful reset, the white and blue lights will flash quickly
- Game mode: Enter the game mode with any five clicks of the left and right buttons, and exit with another five clicks.
• LED indicating status
- Place the earphones in the charging box, and the blue light of the earphones will remain on, while the blue light of the charging box will remain on.
- Take out the charging case of the earphones, and the white and blue lights flash alternately.
- Pair headphones, with the auxiliary ear light off and the main ear white and blue light flashing.
- Successfully paired the earphones with the phone, but the earphone light is off.
- Charge the charging box with a single blue light flashing and a constant blue light when fully charged.
- Place the earphones into the charging box for charging. The charging compartment light remains on, the earphone fully charged light goes out, and the box light goes out.
• Matters needing attention
- Do not use abrasive cleaners to clean this product.
- Do not allow this product to be heated or close to a fire source, such as a cooking stove.
- Do not expose the product to direct sunlight for a long time.
- Do not discard this product in fire to avoid explosion.
- Do not attempt to disassemble this product to make any modifications, as it does not contain any maintenance components.
- Do not use this product in rain.
- If you do not plan to use this product for a long time, please store it in a dry environment and charge the headset less once to prolong its life and avoid extreme temperature and dust.
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.