Shenzhen Lanlian Digital Technology WD-500 Wireless Charging Clock Speaker User Guide

: June 4, 2024
: Shenzhen Lanlian Digital Technology

Table of Contents

Shenzhen Lanlian Digital Technology WD-500 Wireless Charging Clock
Safety Instructions
Notice to User
What’s Included
Overview
Button Functions
Operation
Wireless Charge
Bluetooth Pairing (BT Mode)
Snooze & Alarm Dismiss
FCC STATEMENT :
Specification:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shenzhen Lanlian Digital Technology WD-500 Wireless Charging Clock

Speaker

We would like to congratulate you on the purchase of your WD-500 Wireless Charge Clock Speaker. Please read this manual carefully before use.

Safety Instructions

Please read the following instructions. Failure to follow all the instructions listed below may damage the device and/or may result in electric shock, fire and/or personal injury.

Do not expose the device to direct sunlight
Do not remove screws from or open the device casing by yourself
To reduce the risk of fire or electric shockˇ˘do not expose this equipment to rain or moistures.
The unit shall not be exposed to dripping or splashing and objects filled with liquidsˇ˘such as vases shall not be placed on the unit.
Never charge the device with a damaged power cable.
Never put the device or power cable near heat registers, radiators, stoves or heaters.
Always put the device where it is not easily knocked over by persons in household or business.
Never touch the device with wet hands.
This device is only for the intended household or in-door use.
Never use any detergents to clean any part of the unit.

Notice to User

Please make sure use the provide adapter to connect the device
This device can only wireless charge mobile phones that have standard wireless charging function.
Wearing a metal phone case or a plastic phone case that is too thick will block the wireless charging transmission. Please remove the phone case when wireless charging your mobile phone.
There may be signal interference and an increase in noise in FM radio mode when wireless charge function is being used at the same time.
For safely reasonsˇ˘he device wireless charging function may temporarily stop when overheating is detected during the wireless charging process.
Wireless charge function requires power connection to a fast charge power plug.

What’s Included

WD-500 device*1,
adapter*1,
user manual*1

Overview

Button Functions

Power Button：
- Long press: Power On/Off
- Short press: Enter/Quit Clock Mode when the device is powered on
Volume Up Button：
- Short / Long press: Increase volume
- Adjust the time
Mode Button(Time setting Button): Short press: Switch Mode
- Short press: Time Set (Clock Mode) Long press: Adjust Bass
Previous Button:Short press: Previous
Play/Pause Button：Short press: Play/Pause (BT mode,
next Button:
- Short press: Next
- Long press: Switch between C / F Format
Alarm 1 & Alarm 2 Button: Short press the tbutton to set the corresponding alarm. Press the Long press button to enable or disable the corresponding alarm.
Volume Down Button:
- Short / Long press: Reduce volume / Adjust the time
Snooze Button: Short press: 5 mins snooze (Alarm buzzing) Short press: Screen dimmer Long press: Night light On/Off

Operation

To power the device, use the provide adapter connect to the DC jack of WD-500, the other end is connected to the power, the device will start and enter the clock mode .Use the USB (not included) cable, connect the USB-A end into the WD-500 “USB Output” port, connect the other end to connect to the phone port to charge.
Note:
When using external charging, the device needs to be connected to the power supply.

Wireless Charge

A connection to adapter is required to power the wireless charging function. To wireless charge your phone, place the phone on the wireless charging area of the device with the display facing up. If charging is unstable, adjust the position of the phone to make sure that the phone centers with the charging area and touches the non-slip rubber pad. The wireless charge indicator lights up when charging. Some mobile phone cases may a˜ect or block wireless charging output. Remove them if necessary. The wireless charge led indicator blinks if metals are detected indicating there is an abnormal situation. Remove any metals on the device immediately to prevent overheating.

Bluetooth Pairing (BT Mode)

Use the button to switch to Pairing mode. A blue dot on the display ready to pair a mobile device. On your Bluetooth device, ÿnd and select “WD-500” under your bluetooth device listing to pair. A successful connection via bluetooth will be followed by an audible notiÿcation. For help with Bluetooth Settings, please consult your device’s user manual.

Handsfree Speakerphone
The handsfree speakerphone function is enabled when the device is paired with your mobile device. Press the button to answer an incoming For the best conversation experiece, make sure the WD-500 unit is placed near (within 40cm) the user .

Auxiliary Connectin (Aux-In Mode)
Use the AUX cable（not included）connect one end to the AUX Out jack of the audio source device and the other end to the AUX In jack on Please note that the FM signal will weaken in indoor or closed environments. Noise or signal interference may occur in the FM radio mode

Set Time
This device can automatically synchronizes the time for some mobile phone models after it is connected with the phone through Bluetooth. It requires your phone to support this function in order to synchronize the time. If the time on the device is not updated after it is connected to the phone through bluetooth, then you may need to set the time manually through the following procedures

Snooze & Alarm Dismiss

When the alarm is buzzing, short press the for 5 minutes. The alarm will buzz again after 5 minutes. To dismiss the alarm, press any buttons except tbutton when the alarm is buzzing. This will dismiss the alarm for the current day and the alarm will still buzz again the next day. To fully disable the alarm. long press the alarm button until the corresponding alarm icon on the display disappeared.

FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that maycause undesired operation.
Warning:
Changes or modiÿcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been te sted and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter ference in a residen tial installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the in structions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o˜ and on, the user is encouraged to try to correct the interference by one or more of the following. measures:

Reorient or relocate the receiving an tenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit di˜erent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.