Shenzhen Epplos Electronics EP3056T-E5.2V PCBA Bluetooth Audio Transmitter User Manual

Shenzhen Epplos Electronics EP3056T-E5.2V PCBA Bluetooth Audio

Transmitter

Product Features

1. Turn your regular stereo audio devices into a Bluetooth-enabled, wireless streaming machine through 3.5mm audio-out jack.
2. Work with any type and brand of device such as TV, PC, CD player, iPod, MP3/MP4 etc. up to 10 meters working range.
3. Easy pairing with Bluetooth stereo headset, headphones, speakers and other Bluetooth stereo audio enabled systems.
4. Use high sensitivity level,high performance QCC3056 chip,High performance Bluetooth 5.0 with A2DP protocol based on 2.4GHZ working frequency for improved audio quality.Support SBC,aptX,aptX-HD make you to enjoy the stereo music without,Wire restriction.Also the receiver can use AVRCP protocol to control the,players playing/stop ,up/down functions

How to Use

1. Audio sources:Connect the audio Bluetooth transmitter module to any devices with 3.5mm audio cable.
2. Power:Power on the module by DC 5V
3. Pairing: After power on, the module is searching and pairing automatically when signal searched.
4. Connection: When the module’s LEDs flashing alternatives means the module is connected successfully

Specifications

1. Bluetooth Version : 5.2
2. Transmission distance: 10 meters
3. Support format: SBC,APTX,APTX-HD
4. Unit size: 40 27 1.2 mm

FCC regulatory conformance：

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.

IC regulatory conformance
This device complies with CAN ICES-003 (B)/NMB-003(B).
This device contains licence exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.

ORIGINAL EQUIPMENT MANUFACTURER (OEM) NOTES

• The OEM must certify the final end product to comply with unintentional radiators (FCC Sections 15.107 and 15.109) before declaring compliance of the final product to Part 15 of the FCC rules and regulations. Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change.
• The OEM must comply with the FCC labeling requirements. If the module’s label is not visible when installed, then an additional permanent label must be applied on the outside of the finished product which states: “Contains transmitter module FCC ID: 2ARV2-EP3056T”. Additionally, the following statement should be included on the label and in the final product’s user manual: “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interferences, and
  2. this device must accept any interference received, including interference that may cause undesired operation.”
• The module is limited to installation in mobile or fixed applications. Separate approval is required for all other operating configurations, including portable configuration with respect to Part 2.1093 and different antenna configurations.
• A module or modules can only be used without additional authorizations if they have been tested and granted under the same intended end‐use operational conditions, including simultaneous transmission operations. When they have not been tested and granted in this manner, additional testing and/or FCC application filing may be required. The most straightforward approach to address additional testing conditions is to have the grantee responsible for the certification of at least one of the modules submit a permissive change application. When having a module grantee file a permissive change is not practical or feasible, the following guidance provides some additional options for host manufacturers. Integrations using modules where additional testing and/or FCC application filing(s) may be required are: (A) a module used in devices requiring additional RF exposure compliance information (e.g., MPE evaluation or SAR testing); (B) limited and/or split modules not meeting all of the module requirements; and (C) simultaneous transmissions for independent collocated transmitters not previously granted together.
• This Module is full modular approval, it is limited to OEM installation ONLY.
• Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change. (OEM) Integrator has to assure compliance of the entire end product include the integrated Module. Additional measurements (15B) and/or equipment authorizations (e.g. Verification) may need to be addressed depending on co-location or simultaneous transmission issues if applicable. (OEM) Integrator is reminded to assure that these installation instructions will not be made available to the end user
• IC labeling requirement for the final end product:
  • The final end product must be labeled in a visible area with the following “Contains IC: 24810-EP3056T”
  • The Host Marketing Name (HMN) must be indicated at any location on the exterior of the host product or product packaging or product literature, which shall be available with the host product or online.
  • Unauthorized modifications could void the user’s authority to operate the equipment.
  • This radio transmitter [lC: 24810-EP3056T] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
    Frequency range| Manufacturer| Peak

gain

| Impedance| Antenna type
---|---|---|---|---
2400-2483.5MHz| EPPLOS ELECTRONICS

CO.,LIMITED

| 0dBi| 50Ω| PCB Antenna

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>