superbrightleds com STREB-Y1 48 Inch Bar LED Light Instructions

superbrightleds com STREB-Y1 48 Inch Bar LED Light

Product Information

Specifications

• Version: 20221005-506
• Operating Voltage: DC 12-24V
• 22 Flash Patterns (Form A)
• 48 Flash Patterns (Form B)
• 48 Bar
• Wiring:
  • 2 types without junction box
  • 2 types with junction box

Product Usage Instructions

Power On/Off

To turn the product on or off, follow these steps:

1. Press the power button for less than 1 second to toggle the power.

Flash Pattern Selection and Intensity Control

To select flash patterns and control the intensity of the light, follow these steps:

1. To cycle through flash patterns:
   • Press the flash pattern selector button for less than 1 second to move to the next pattern.
   • Press the flash pattern selector button for 1-3 seconds to move to the previous pattern.
2. To adjust the intensity:
   • Press the flash pattern selector button for over 5 seconds to activate low-intensity mode.
   • Press the flash pattern selector button for over 5 seconds again to return to normal intensity.

Dual Color Mode (if applicable)

If your product supports dual-colour mode, follow these steps to switch between colours:

1. Press the flash pattern selector button for 3-5 seconds to switch from color 1 to color 2.
2. Press the flash pattern selector button for 3-5 seconds again to alternate between colour 1 and colour 2.
3. Press the flash pattern selector button for 3-5 seconds again to return to colour 1.

Wiring Instructions

The wiring instructions depend on the number of wires and the presence of a junction box. Follow the instructions based on your setup:

• When using 4 wires:
  • Yellow wire: Flash pattern selection
  • Connect the yellow wire to the red wire momentarily (less than 1 second) to move to the next pattern.
  • Connect the yellow wire to the red wire for 1-3 seconds to move to the previous pattern.
  • Connect the yellow wire to the red wire for 3-5 seconds to return to pattern #1.
• When using 5 wires:
  • Yellow wire: Flash pattern selection (same instructions as for 4 wires)
  • Grey wire (Low power): Connect the grey wire and red wire to positive to enable low power mode for flash patterns. Disconnecting the grey wire from positive will return to normal power.
  • Blue wire: Synchronization

Installation

After wiring the product, ensure that it is securely mounted before use.

Optional Features

If your product includes a junction box, it may support additional features such as low-power mode. Refer to the specific instructions provided with the junction box for details.

FAQ (Frequently Asked Questions)

• Q: How do I select a specific flash pattern?
• A: To select a flash pattern, use the flash pattern selector button and follow the instructions provided in the “Flash Pattern Selection and Intensity Control” section above.
• Q: How do I adjust the intensity of the light?
• A: To adjust the intensity, use the flash pattern selector button and follow the instructions provided in the “Flash Pattern Selection and Intensity Control” section above.
• Q: How do I switch between colours in dual-colour mode?
• A: If your product supports dual colour mode, use the flash pattern selector button and follow the instructions in the “Dual Color Mode” section above.
• Q: How do I wire the product?
• A: The wiring instructions depend on the number of wires and the presence of a junction box. Refer to the “Wiring Instructions” section above for detailed instructions based on your setup.
• Q: What should I do after wiring the product?
• A: After wiring, make sure that the product is securely mounted before use. Refer to the “Installation” section above for more information.
• Q: What additional features are available with the junction box?
• A: If your product includes a junction box, it may support additional features such as low power mode. Refer to the specific instructions provided with the junction box for details.

INTRODUCTION

• Operating Voltage: DC 12-24V
• Operation temperature: -30°C to +60°C
• Easy mounting with brackets

Feature

• Mounting permanently to the vehicle or using an optional roof mounting kit
• With memory function
• Reverse polarity protection
• Polycarbonate lens with UV-resistant
• The tough polycarbonate lens and solid aluminium base make it durable to use and resist compression

22″: 26 Flash Patterns (Form A)

1| Single flash (ECE R65)| 10| Quad flash (ECE R65)| 19| Left and right constant flash
---|---|---|---|---|---
2| Double flash (ECE R65)| 11| Eight flash| 20| Single flash (ECE R65)
3| Eight – half to half| 12| Twelve flash| 21| Double flash + Rotation
4| Cross flash| 13| CW constant flash| 22| One-one single flash
5| CW Rotation – triple| 14| CCW constant flash| 23| One-one eight flash
6| CCW Rotation – triple| 15| CW constant on| 24| Left Steady Right Single
7| All – half to half| 16| CCW constant on| 25| Left Single Right Steady
8| All – Single – Quick| 17| CW Rotation| 26| Steady on
9| Triple flash (ECE R65)| 18| CCW Rotation| |

Mounting: magnet bracket or bolt

Wiring Options

Cigar plug

• Press less than 1s for the next pattern.
• Press 1-3s for the previous pattern.
• Press more than 5s for low intensity, and press more than 5s again back to normal intensity.
• For dual color: press 3-5s to change color 1 to color 2, press 3-5s again for color 1 alternate to color 2, and press 3-5s again back to color 1.

Wires: (With memory function)

• RED: +VDC
• BLACK: -GROUND
• GREY: (different type apply to different wires, type reference to Page 1)
• …..type *: constantly connect to red wire to achieve low intensity.
• ….type * 5: constantly connect to the black wire to achieve low intensity.
• YELLOW: (type
• (1) apply to red wire, type
• 5 apply to black wire)
• ….less than 1s for the next pattern.
• ……1-3s for the previous pattern.
• …3-5s for changing colour 1 to colour 2, 3-5s again for colour 1 alternate to colour 2, 3-5s again back to colour 1.
• more than 5s for low intensity, more than 5s again back to normal intensity.
• WHITE: connect White wires of all heads for synchronization

48”: 29 Flash Patterns (Form B)

Remark: If in dual colour mode, each pattern will flash colour 1 and then colour 2. (Except #29)

Mounting System

48″ Bar
Steps

1. Mount the rubber pads on the brackets, see fig.1.
2. Fit the hook bracket and angle bracket into one piece with bolts, washers and nuts, see fig.2.
3. Put the light bar in the desired location on the roof of the vehicle. (Usually, the light bar should be in the centre.)
4. Fix the hook bracket to the light bar, see fig.3.

After installation, check the light bar to ensure it is securely mounted.

Wiring

Totally 4 types

• 2 types without junction box
• 2 types with junction box

Without junction box
Option 1: With 4 or 5 wires directly
*When with 4 wires:

• Red: Positive +
• Black: Negative –
• Yellow: Flash pattern selection
• Apply Yellow to Red
• Less than 1 second for the next pattern
• 1 to 3 seconds for the previous pattern
• 3 to 5 seconds back to pattern #1 *
• Blue: Synchronization

When with 5 wires

• Red: Positive +
• Black: Negative –
• Yellow: Flash pattern selection
• Apply Yellow to Red
• Less than 1 second for the next pattern
• 1 to 3 seconds for the previous pattern
• 3 to 5 seconds back to pattern #1
• Grey (Low power): constantly connect grey wire and red wire to positive, then the light bar will be Low power of flash pattern. When disconnect grey wire to positive, it will be back to normal power.
• Blue: Synchronization

Option 2: With controller box directly (Standard)

• Red: Positive +
• Black: Negative –

Achieve functions by the buttons on the controller box

Function of controller

With junction box

Option 3: With junction box (without controller box)

• Red: Positive +
• Black: Negative –

• Achieve functions by the wires from Port 1 and Port 2.
• Depending on the customer’s requirements, some wires may be unused.

wires function (Port 2)

1. Yellow (ON/OFF): constantly connect the yellow wire to the red wire (positive), and then the lightbar will start working.
2. Purple (Flash pattern selector): apply to the red wire (positive), less than 1s for the next pattern.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>