70mai Dash Cam 3 User Manual

70mai Dash Cam 3 User Manual

Product overview

Please read this manual carefully before using the product and keep it in a safe place.

1. Microphone

2. Ring indicator light

3. Mounting bracket

4. Memory card slot

5. Power port

6. Adhesive sticker

7. Screw

8. Speaker

9. Camera

10. Power button
    

Specifications

Product: Dash Cam
Model: M200
Input: 5V 1.5A
Battery capacity: 300mAh
Battery type: Li-ion battery
Wireless connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz
Wi-Fi operation frequency: 2400–2483.5MHz
Wi-Fi maximum output: < 20dBm

Packing list

1. Dash Cam × 1
2. Power cord × 1
3. Car charger × 1
4. Electrostatic sticker × 2
5. Adhesive sticker × 1
6. Wiring trim tool × 1
7. User manual × 1

Installation

1. Installing the electrostatic sticker
   Paste the electrostatic sticker on the recommended area on the front windshield.
   Press the sticker to remove air bubbles out.
   Avoid the edge of the windshield and select the flat and smooth area for the installation.
   Note: Keep windshield clean and dry without liquid residue to prevent the sticker from losing adhesion and dash cam from dropping.

2. Installing the memory card
   Insert the memory card into the card slot with its contacts facing up.

3. Mounting the dash cam
   Paste the dash cam onto the electrostatic sticker.

4. Routing cable
   Route the power cord to the vehicle’s power outlet and connect to power .
   Start the car engine, and the dash cam will automatically turn on.
   Note: Depending on the vehicle, the power outlet may be located in a different position. The provided figure is for reference only

5. Adjusting the camera angle
   Bind the dash cam to the 70mai app following the instructions in the user guide.
   Adjust the camera angle based on the image presented in the dash cam’s homepage.

Button functions

Press the power button a different number of times to perform different functions.

authorization

Note: The dash cam can be turned on by pressing the power button only when it is connected to an external power supply.

Voice control

Dash cam supports voice control. During the operation of the dash cam, the voice commands from the user will trigger the relevant functions of the dash cam.
If the system language of the dash cam is set to Traditional Chinese, the Mandarin voice commands are supported. If any other language is set, only the English voice commands are supported.
The voice commands are as follows:

emergency video directory.
Lock the video| Dash cam will record audio as well as videos.
Turn off audio| Dash cam will not record audio but only video

Note: When the dash cam is connected to the 70mai app, voice control is not supported.

Downloading 70mai app

This product needs to be used in conjunction with the 70mai app. You can download and install the app by scanning the QR code or finding “70mai” in the app store.
Note: Android 5.0 & iOS 11.0 or above is required to connect to the dash cam’s Wi-Fi hotspot with a mobile phone.
Dash cam Wi-Fi hotspot information
Hotspot name: 70mai_M200_XXXX (Please check the label on the device for the hotspot name.)
Default password: 12345678
Please refer to the user guide for how to establish a connection.

Memory card instructions

• A memory card (sold separately) must be installed in the dash cam before use.
• The dash cam supports standard microSD cards. Please use memory cards with the capacity between 16GB to 128GB and rating speed of Class10 or above.
• The default file partition format of the memory card may be inconsistent with the format supported by the dash cam. When inserting the memory card for the first time, please format it in the dash cam before use. Formatting the memory card will delete all files on the card. Please back up important data to another device beforehand.
• The memory card may become damaged or deteriorated after repeated cycles of overwriting, and this may affect its ability to save video and image files. If this occurs, immediately replace it with a new memory card.
• Please use a high-quality memory card purchased from a reputable vendor. Inferior memory cards may have issues such as the actual reading/writing speeds do not match the stated speeds, and the actual storage capacity does not match the stated storage capacity. We shall not be held liable for lost or damaged videos caused by the use of a lowquality memory card.
• Do not insert or remove the memory card while the dash cam is turned on.

Precautions

Before using this dash cam, please read all the precautions and user guide to ensure correct and safe use.

• This dash cam is a driving aid designed to record external images of the vehicle. And it does not have the function of ensuring the user’s driving safety. Users must abide by local traffic rules and regulations and take driving safety as a priority consideration. Do not operate this product while driving.
• Due to differences in vehicle conditions, driving style, driving environment, and other factors, some functions may not work properly. A power failure, usage in environments outside the normal operating temperature or humidity range, a collision, or a damaged memory card may cause the dash cam to function abnormally. There is no guarantee that this dash cam will function normally under all circumstances. Videos recorded by this dash cam are for reference purposes only.
• Please install this dash cam correctly, and do not block the driver’s line of sight, or block the vehicle’s airbag, in order to avoid product failure or personal injury.
• If the front windshield where the dash cam is installed is covered with colored automotive film, it may affect the video recording quality or cause video distortion.
• Avoid collisions or forceful jolt to the dash cam, otherwise the product may malfunction.
• Never use chemical solvent or detergent to wash the dash cam.
• Keep this dash cam away from any strong magnetic fields, as they may cause damage to the dash cam.
• Do not use this dash cam in environments with temperatures over 60°C or below -10°C.
• When the dash cam has been operating for a period of time, the temperature of the outer casing will rise, please be careful when touching.
• Please only use this dash cam within the scope permitted by law.
• Please use the included car charger, power cord, and other accessories in order to avoid product failure due to nonconformance. We shall not be held liable for any loss or damage caused by the use of a non genuine car charger or power cord.
• If you use power adapter to charge the dash cam, only use the power adapters that comply with the local safety standards or certified and supplied by qualified manufacturers.
• The dash cam and its accessories may contain small parts. To avoid choking or other hazards or damages caused by the children, keep the dash cam out of the reach of children.

Regulatory compliance information

WEEE information

All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/ EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU declaration of conformity

The manufacturer hereby, declares that this equipment is in compliance with the applicable Directives and European Norms, and amendments. The full text of the EU declaration of conformity is available at the following internet address: https://help.70mai.asia/1193.html.

Hereby, 70mai Co.,Ltd. declares that the radio equipment type M200 is in compliance with Radio Equipment Regulations 2017. The full text of the UKCA declaration of conformity is available at the following internet address: https://help.70mai.asia/2145.html.

Cautions

• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• This device is equipped with a built-in battery that cannot be removed or replaced. Do not disassemble or modify the battery by yourself.
• Replacement of a battery with an incorrect type can defeat a safeguard (for example, in the case of some lithium battery types).

FCC Caution.

15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC ID: 2AOK9-M200.

ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED Radiation Exposure statement
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
IC: 28033-M200

Scan the QR code and email us at [email protected]

View the User guide for product functions and FAQs.

Service: [email protected]
For further information, please go to www.70mai.com
Manufacturer: 70mai Co., Ltd.
Address: Room 2220, Building 2, No. 588 Zixing Road, Minhang District, Shanghai, China

References

• 70mai: Innovator in Smart Dash Cams
• 70mai: Innovator in Smart Dash Cams
• UK declaration of conformity

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>