DANCO 12097 Universal Adjustable Toilet Fill Valve Instruction Manual

June 16, 2024
DANCO

INSTALLATION INSTRUCTIONS
FOR 3″ ADJUSTABLE FLUSH VALVE
Visit
DANCO.COM
for Easy D.1.Y. Solutions

12097 Universal Adjustable Toilet Fill Valve

Tools Required:

WARNING
DANCO 12097 Universal Adjustable Toilet Fill Valve - Tools
2 DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS.
Use of such products will RESULT IN DAMAGE to tank components and MAY CAUSE FLOODING and PROPERTY DAMAGE and VOID WARRANTY. DO NOT overtighten nut or tank/bowl may crack Inspect unit every 6 months and replace f there are any signs of cracking, deterioraion, or wear and tear

DANCO 12097 Universal Adjustable Toilet Fill Valve - Figure
1 Prepare Tank: Shut water supply valve off by turning valve clockwise, flush toilet to empty tank. Remove any excess water left in tank with sponge or towel. Disconnect water supply line coupling nut from bottom tank of Fill Valve by turning coupling nut clockwise. Place bucket under tank to catch residual water. DANCO 12097 Universal
Adjustable Toilet Fill Valve - Figure 2Remove 0ld Flush Valve: Unhook flapper chain from tank lever.
(Use Adjustable Pliers) Unbolt tank from toilet bow, lift tank and lay on its side on a safe and secure surface. Remove all bolts, hex nuts, metal flat washers, and rubber washers (not shown).
Remove Tank-to-Bowl-Gasket from under tank. (Use Adjustable Pliers) on Lock Nut turning clockwise for removal and remove old Flush Valve from tank.
Attention: If Tank-to-Bowl-Gasket shows signs of wear or deterioration, obtain and install a new gasket before installing new Adjustable Flush Valve. DANCO 12097 Universal Adjustable Toilet Fill Valve - Figure
3Install Adjustable Flush Valve: Insert new Adjustable Flush Valve into tank hole. Position overflow tube toward back of tank (Do not cover bolt holes of tank). Holding Adjustable Flush Valve in place, hand tighten Lock Nut counter-clockwise and check for leaks. If leaking is detected, hand tighten additional 1/4 turn.
Do not overtighten or tank may crack resulting in leakage and/or flooding.
Place Tank-to-Bowl-Gasket on bottom of Lock Nut. Bowl Gasket should cover Lock Nut. DANCO 12097 Universal Adjustable Toilet Fill Valve - Figure
4 Installing Toilet Bolts: Place one rubber washer on each tank bolt. Place bolts inside tank through bottom holes of tank. Set tank onto bowl. Place metal washers and hex nuts on each bolt underneath toilet bowl. Hand-tighten hex nuts counter-clockwise evenly until tank is snug and does not rock. Do not overtighten or tank may crack resulting in flooding. DANCO 12097 Universal Adjustable Toilet Fill Valve -
Figure 5Preparing Adjustable Flush Valve: (Step 5a) Pull internal overflow adjustment tube upward or push downward using numerical height adjustment guide at 3/8” increment markings for height adjustment provided it’s no higher than the 1″ distance between Port Line and top of Overflow Tube. (See STEP 6).
(Step 5b) Turn internal tube full 3/4” clockwise to lock in place as shown. DANCO 12097 Universal Adjustable Toilet Fill Valve - Figure
6Adjust Adjustable Flush Valve: The height adjustment should be no higher than the 1″ distance between Port Line and top of Overflow Tube.
Overflow Tube Once the Internal Overflow Adjustment Tube is set. Turn internal tube 3/4-turn clockwise to lock in place. DANCO 12097 Universal Adjustable
Toilet Fill Valve - Figure 7Reattach Refill Tube: To reattach Refill Tube attach one end of refill tube to Tube Port. Attach other end with Clip to top of Overflow Tube.
Warning: Do not insert refill tubing down Overflow Pipe may cause significant water waste. ![DANCO 12097 Universal Adjustable Toilet Fill Valve

  • Figure 8](https://manuals.plus/wp-content/uploads/2024/01/DANCO-12097 -Universal-Adjustable-Toilet-Fill-Valve-Figure-8.jpg) Attaching Flapper Chain: Attach chain link to lever handle bar directly above the flapper. Leave 1/2 inch of slack in the chain. DANCO 12097 Universal Adjustable
Toilet Fill Valve - Figure 9Attach Water Supply Connector: Attach water supply coupling nut to fill valve.Turn counter-clockwise by hand until tight.
    Warning: Overtightening the nut could damage fill valve or coupling nut that may result in the nut cracking resulting in leakage and/or flooding.
    To check for leaks, turn on water supply valve. Should leaking occur-turn coupling nut enough to stop leaking. Flush toilet to check.
    DO NOT USE PLUMBER’S PUTTY TO SEAL FITTINGS.

©2023 Manufactured for
Danco, Inc.,Irving, TX 75062
Made in China
120971

Documents / Resources

| DANCO 12097 Universal Adjustable Toilet Fill Valve [pdf] Instruction Manual
12097 Universal Adjustable Toilet Fill Valve, 12097, Universal Adjustable Toilet Fill Valve, Adjustable Toilet Fill Valve, Toilet Fill Valve, Fill Valve
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals