ENKIN PDM250 250W LED Intelligent Multi Way Dimmer User Manual
- June 16, 2024
- ENKIN
Table of Contents
ENKIN PDM250 250W LED Intelligent Multi Way Dimmer
Product Information
Specifications:
- Product Name: PDM250
- Product Type: LED Intelligent Multi-Way Dimmer
- Operating Voltage: 240V ac
- Nominal Operating Frequency: 50 Hz
- Dimming Technique: Trailing edge phase control only
- Compliance: BS EN 60669-2-1
- Load Symbol:
- Compatible Loads:
- Dimmable LED lighting – Max Load: 250W, Min Load: 2W
- 240V Incandescent & Halogen lamps – Max Load: 250W, Min Load: 2W
- Low voltage lighting with electronic transformers – Max Load: 250W, Min Load: 2W
Product Usage Instructions
ON/OFF & DIMMING FUNCTION
The dimmer switch is activated by pressing the dimmer shaft only. The dimming
function is controlled by rotating the dimmer shaft.
Setting the Minimum Level (Anywhere below 50% of range)
- While the dimmer is on, slowly adjust the dimmer to your desired minimum brightness.
- Push the rear setup button 3 times within 2 seconds.
- The LEDs will step up and down in brightness once to confirm that the setting has been saved.
Setting the Maximum Level (Anywhere above 50% of range)
- While the dimmer is on, slowly adjust the dimmer to your desired maximum brightness.
- Push the rear setup button 5 times within 3 seconds.
- The LEDs will step up and down in brightness once to confirm that the setting has been saved.
Factory Reset for Min/Max Brightness
Please note that this factory reset will reset all the min and max brightness
settings.
- While the dimmer is on, push the rear setup button 7 times within 5 seconds.
- The LEDs will step up and down in brightness three times to confirm that the min/max setting has been cleared.
Wiring Diagram – Single PDM250 Dimmer Switch
Wiring Diagram – Multiple PDM250 Dimmer Switches
FAQ
Q: Can this product be used for outdoor lighting?
A: No, this product is suitable for indoor use only.
Q: How should I dispose of this product?
A: Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your local authority
or retailer for recycling advice.
PDM250
250W LED Intelligent Multi-Way Dimmer
- Easy push button setup
- Trailing Edge
- Soft start feature
- Multi-way dimming of up to 20 PDM250 dimmers
- Silent & flicker free
- Self Recovering Thermal Fuse
- Short Circuit Protection
- Overload Protection
| Operating Voltage | 240V ac |
|---|---|
| Nominal Operating Frequency | 50 Hz |
| Dimming Technique | Trailing edge phase control only |
| Compliance | BS EN 60669-2-1 |
| Load Symbol | Compatible Loads |
Dimmable LED lighting
|
250W
|
2W
| 240V Incandescent & Halogen lamps|
250W
|
2W
| Low voltage lighting with electronic transformers|
250W
|
2W
Multi-Gang Switch De-Rating Chart
1 Gang| 2 Gang| 3 Gang| 4 Gang| 5 Gang
250W| 212.5W| 175W| 137.5W| 100W
OPERATING INSTRUCTIONS
MULTI-WAY DIMMING – FUNCTIONALITY
Multiple PDM250 dimmers in a connected set (connected in parallel), will all
share the same settings and dimming position, including high and low settings.
Because of this, it is important to only use the same luminaire type, per set
of dimmers to avoid any mismatch between high and low settings.
It is only necessary to perform any hi/low or reset button sequences on one of
the PDM250 dimmers connected in a set, this must be performed only after all
dimmers on the circuit have been connected together.
IMPORTANT NOTE: The PDM250 only works with other PDM250s and will not
work in conjunction with any other type of dimmer switch.
A reset sequence must be performed if dimmers are added or subtracted from the
circuit, or luminaire type is changed, and then hi/low setup repeated.
ON OFF & DIMMING FUNCTION
Dimmer switch is activated by pressing the dimmer shaft only, dimming function
by rotating the dimmer shaft only.
REAR PANEL PRESS BUTTON – DIMMER SETUP SEQUENCES
Setting the Minimum Level (Anywhere below 50% of range)
- Whilst on, slowly adjust dimmer to your desired minimum brightness.
- Push the rear setup button 3 times within 2 seconds.
- The LEDs will step up and down in brightness once to confirm the setting has been saved.
Setting the Maximum Level (Anywhere above 50% of range)
- Whilst on, slowly adjust dimmer to your desired maximum brightness.
- Push the rear setup button 5 times within 3 seconds.
- The LEDs will step up and down in brightness once to confirm the setting has been saved.
Factory reset for Min/Max brightness
Please note this factory reset will reset all the min and max brightness
settings.
- Whilst on, push the rear setup button 7 times within 5 seconds.
- The LEDs will step up and down in brightness three times to confirm that the min/max setting has been cleared.
WIRING DIAGRAM – SINGLE PDM250 DIMMER SWITCH
WIRING DIAGRAM – MULTIPLE PDM250 DIMMER SWITCHES
WARNING – PLEASE READ RISK OF ELECTRIC SHOCK
- Hazardous voltage and electrical current may be present at the wire leads of this product even when the device is switched off.
- Lock out and tag the input circuit before accessing the wiring connections.
- This device must be installed by a qualified and experienced electrician in accordance with applicable current electrical regulation.
- To comply with all safety standards, the product must be used only for the purpose described in this instruction and must be installed in accordance with the wiring rules and regulation in the location where it is installed.
- There are no user serviceable parts inside the product.
Failure to follow these instructions can result in death or serious injury.
EQUIPMENT DAMAGE HAZARD
- Install the device according to instructions in this document.
- Pay attention to the specifications and wiring diagrams related to the installation.
- Do not use this product for any other purpose than specified in this instruction.
- The product is suitable for indoor use only.
- Apply IEC60898-1 compliant 250V~ 6A MCB as an overload protective device.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
LEGAL DISCLAIMER
The installation of electrical products is inherently dangerous and can lead
to serious injury or death. The products we sell MUST be installed by a
qualified and experienced electrician in accordance with applicable current
electrical regulation. Any advice, guidance or other information provided by
Enkin on their website or within any of our publications cannot completely
anticipate your situation and common sense must prevail. Products need to be
checked prior to installation and regularly for damage and wear and tear.
Products should be returned and not used if in any doubt of their integrity.
Electrical rated loads and limits of a given product should NEVER be exceeded
at any time. The electricity supply should always be isolated at its source
(Distribution Board) before attempting any installation or maintenance.
No advice or information, whether oral or written, obtained by you from us or
through the service, our employees, consultants and/or retailers shall create
any warranty not expressly made herein.
You agree to assume all and any risk resulting from the utilisation of
information provided by Enkin. You also expressly agree not to hold us
responsible for any damage, personal injury, death or loss resulting from your
use of our information, service or regulatory compliant products.
Enkin is a trading name of Trade Ivy. Registered in England Number: 10809945.
Copyright © 2021
All Rights Reserved. Trade Ivy Limited, Unit 3C Latham Park, St Blazey Road,
Par, PL24 2HY.
Scan QR Code for more detailed technical information on this product
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>